Lathe duplicator

[@joepie221]

Nice attachment, but I would suggest turning the smallest end diameters last. Maintain the support for as long as you can for rigidity and safety. Same principle for turning steel.

[@clarknjapan]

Great info! I would take off your ring prior to putting hands near the turning lathe.

[@bikersoncall]

😄

[@robertcornelius3514]

Nice machine. It looks like you need another lathe. One for the duplicator and one for final finishing.

[@ins614317]

Do you have plans of how you made this? This is awesome. I’m subscribing to this.

[@gordlanger7064]

Hi the duplicator is from Vega . I purchases it from them. It was expensive but well worth it. Thank you for your comments. Gord

[@sethshoemaker4408]

What lathe are you using? I’d love to get one

[@patrickbrennan2864]

I’ve found that burnishing the wood produces a gorgeous and hard finish (after sanding) - I often use a cutoff from an oily species like olive, and rub it firmly against the rotating piece (at low speeds)

[@thecatreusco529]

Great video! Please let me know template's typical extra room from the end of profile to be left for holding down in the duplicator.à

[@bikersoncall]

I learned some things, thanks.

[@joliekarno]

Thanks for this! Do you have the cutter head in the center or just below center? Mine is leaving a lousy finish. It looks like it was a stabbed a bunch.

[@gordlanger7064]

Hi. Yes the cutter head should be just below center. I would suggest you speed up the lathe speed and be sure to keep the "ship wheel" moving at all times.

[@joliekarno]

@@gordlanger7064 Thanks Gord! I’m doing both of these things that I’m wondering if I am sharpening my cutter incorrectly. Do you have any advice about that?

[@kapitanleutnant1]

Will that lathe duplicator work well with mahogany?

[@danblanchard6739]

I made a shield out of a polycarbonate panel that I folded and stretched to the top of the duplicater. It does a great job of keeping shavings from hitting me and also make cleanup easier

[@mavenfeliciano1710]

What technique do you use to form/manipulate the polycarbonate?

[@danblanchard6739]

@@mavenfeliciano1710 I just used a heat gun and folded it over the edge of a board.

[@gordlanger7064]

Hi Wayne, I get between $40 and $60.00 / pin depending on the type of wood being used. Cheers, Gord.

[@clipperbet]

Do you have a video om the set up of a Vega dup. I just got a used one and need help Terry

[@gordlanger7064]

Sorry do not have a set up video. Perhaps contact vega woodworking directly.

[@OdairLucasLucas]

Ola amigo tudo bem com você Me chamo Odair lucas. Pais Brasil Parabéns. Você teria um vídeo do passo a passo desse seu copiador? Ficou excelente estou precisando fazer um evo seu foi o melhor que eu vi. Mais uma vez parabéns.

[@gordlanger7064]

Olá Odair. Obrigado por seus comentários! Envie-me seu endereço de e-mail e eu lhe enviarei algo. [e-mail]

[@OdairLucasLucas]

Valeu vou enviar. Obrigado

[@OdairLucasLucas]

Olá amigo tudo bem. Com suas informações eu consegui fazer um copiador. Muito obrigado mesmo.

[@guybartlett9587]

Subbed

[@digitaltamer]

Where can I buy that duplicator?

[@The_DC_Kid]

How much do you get for your French Pastry Rolling Pin?

[@johnhunter7386]

Which food grade finish do you recommend? Do you not recommend applying the finish while turning at a slow speed then parting the ends?

[@gordlanger7064]

I use food safe salad bowl finish while on the lathe slow speed to start the high speed to finish off. Then part the ends. Gord

[@gordlanger7064]

Hi Bees Wax or Salad Bowl finish is the best/ safest to use. Gord

[@johnhunter7386]

Thanks, Gord! I look forward to watching more of your videos!

[@keithrenaud3380]

Can you duplicate chess pieces with this?

[@joshdimmick575]

Is there a link to your website?

[@shanerampersad4997]

hello sir it was a great vid were can I get a duplicator like that to buy and how much will it cost thanks

[@shanerampersad4997]

thanks mr langer

[@johnhunter7386]

BTW, thanks for the video!

[@МиронАбрамович-ц9щ]

Цікавий копірувальний пристрій, мені сподобалось.

[@gordlanger7064]

Good idea!

[@bongomakers]

Finish it off with 220 on a random orbit sander while it's turning and you'll have zero scratches.

[@ЖекаСоболь-г3к]

Каска прикольная

[@VVIPUL100]

Can we make a drum stick on this machine?

[@gordlanger7064]

Not sure, sorry. They are thin and may whip without additional support. A Spindle steady rest would help.

[@guybartlett9587]

Thanks

[@abdulazeezseerae1996]

Which (brand) lathe is this ?

[@gordlanger7064]

Hi, its a Vega. All the information needed is in my article (issue #57) on this site: archive.constantcontact.com/fs030/1103251462235/archive/1103792031624.html Cheers, Gord

[@muhammadshabbir8465]

what price Pakistani

[@spettro9]

where's the template...

[@مؤيدمكي-ق2ث]

عمل رائع وجميل .. ممكن ترينا مكونات الصندوق و محتوياته ولكم منا فائق الشكر

[@myronduskin4247]

Any one make one temp plate turn

[@gordlanger7064]

I am sorry I dont understand your question. Gord.

[@victorolveraelvira1548]

verga mucho bla bla y yo sin saber ingles