Learn the art form of measuring an ID using a ball or telescoping gage.

Here we show the art form of measuring an inside dia. within a few tenths. The use of a ball and telescoping gage can be extremely challenging, but all you really need is the proper technique and a delicate touch.
Visit our website www.subtool.com

[@Liberty4Ever]

I think Don is single handedly picking up the slack for the decline in formal machinist training in the US. For those who want to learn how to be a machinist, Don is filling in a lot of the blanks. Thanks Don!

[@houseofbrokendobbsthings5537]

Thanks Don. Measuring a worn engine block, and this was very timely. We do appreciate what you share with us.

[@SuburbanToolInc]

I'm glad you were able to learn something! Thanks again for watching.

[@billbrennan8405]

As always a great video. I was taught 50 years back when using telescoping gages to pul the gage slowly through the bore but to stop recenter the telescoping gage and slowly tip pacst the center point of the bore. Like the ides of using ring gages to practice on first to better develop a proper feel. Using gages like this require the operator to have high defined skill to use them properly. Best BB

[@havebenthere]

Always glued to the screen! Great Video!!! Keep up the good work Don!!!!

[@paulgreenlee190]

This is the second time I have watched this video. I could never get a consistent measurement with the snap gauge but the same was happening with my micrometers. My method was holding it perpendicular and then tightening which caused it to come out of the bore loose. I was using the fine ratchet on the micrometer and it was too tight when I tried to get that gentle slide across the anvils. You have increased my skills to a new level. I wish you could advise me on my 1960 South Bend 13", rear bearing overheating big time but it's a long story and would take 3 or 4 pages to explain. But thank you so much for teaching me how to measure, it will only get better

[@SuburbanToolInc]

Good stuff, thanks for watching.

[@beetlejuice4693]

Love your tools I use them every day

[@SuburbanToolInc]

Thank you so much!

[@paulgreenlee190]

Great explanation on learning skills for measuring. Every hobbyist or beginner needs to learn accuracy. Thanks

[@SuburbanToolInc]

Thank you for watching.

[@meocats]

this cameraman is better than the other one, the filming was more clear this time and the different angles helped

[@SuburbanToolInc]

meocats It is not the camera man as much as it is the improved resolution. We have been adjusting the settings for the camera and the sound. You should see more improvements going forward.

[@Latheman666]

Great video. I have learned a lot. Thanks!

[@886014]

Nice video Don, thanks for putting that up. As somebody almost completely self-taught it's confidence building to confirm that I'm doing things correctly from a master. I'm not so sure about the whole ball on ball measuring thing, and don't think that was a good idea at all. It was however a good demonstration of why flat parts are measured with a ball measuring face, and convex shapes are measured with a flat measurement face

[@SuburbanToolInc]

Pete F Pete , that was just to demonstrate that we are getting a good reading with a second check. I agree that it should be checked with a mic.

[@MrShobar]

Telescoping gages were developed to be used with micrometers. Not height gages (although I appreciate what you are trying to demonstrate). I also like the older gages, like the Lufkin. Best regards, and nice discussion as usual.

[@safeaegis]

Very interesting video. Yes, such measurements can be called art. I recently boring case details, as also used micrometric callipers. The problems are the same - to catch the lowest point. It all worked out, thank you for sharing your own experience.

[@SuburbanToolInc]

Thanks for sharing!

[@MrShobar]

Don, an excellent and informative video (as I've come to expect from you). Please keep it up, my friend.

[@holry7778]

Amazing stuff. Keep'em coming Don. I just bought an great old Logan 11x36 lathe and am reorganizing my shop to make room. This is my first venture from miniature machining. So any video's about how to best do that I know I would enjoy

[@michaelbabatunde3915]

Very good lecture. Many thanks Sir

[@joblessalex]

Trying to redo an engine here and just checking my work, I'm pretty confident in my skills now. Threw a telescoping gauge into my engine and micd it. Threw my bore gauge into the mic and lined it up at 0. Then I threw it into the engine. Came out reading 0. I think I may have the hang of this.

[@dickbernardino5293]

using a telescope gage or ball gage truly depends on old school "feel". However measuring flat surfaces with a micrometer, using the friction thimble or friction ratchet makes the "feel" the same for anyone using those features on modern micrometers.

[@duobob]

Great stuff, Don! More like that, please. This is the stuff that needs to be handed down to the next generation of machinists and tool makers. I want to come work for Suburban Tool, it seems to always be lunchtime there... 8^)

[@SuburbanToolInc]

***** Thanks for the comment Bob , we eat pretty good here.

[@bcbloc02]

Any tips on measuring big bores? I find the bigger the bore the more difficult it can be to find the center since the sides get flatter and flatter. I guess that ID mics fit the bill the best then. I like that squeak feel when I measure, if I get that just right ringing squeak I know I am there.

[@SuburbanToolInc]

bcbloc02 Inside mic or an electronic height gage.

[@dickbernardino5293]

+bcbloc02 measuring ids with inside micrometers takes a scientific approach. the inside micrometer have the spindle end held stationary as the pivot. the micrometer should be moved in a arc perpendicular to the bore axis moving the micrometer thimble out to find the high point of the arc with a light drag. this same method should be should be used moving the micrometer in a arc parallel to the id axis. note a "squeaky" feel could mean a tight "feel"

[@darrenmcsorley3726]

Im curious on what I need to get started as a hobbyist machinist. I am a electrician by trade, and spent many years working in industrial plants working as a electrician/slash mechanic building and working on equipment, so I learned a lot of basics with welding and using milling machines, but no means a skilled machinist by trade. I picked up some tips and tricks from the guys in the shops. Anyway my question is this. I have just bought a affordable mini mill for home use, and the mill comes with nothing but a precision vise and a chuck. no collets nothing. What would you recommend as a starter kit to get me going on a budget, or what are the basic tools or cutters I will need to get started. Thank you

[@SuburbanToolInc]

It depends on what you want to be done. check out our website www.subtool.com

[@darrenmcsorley3726]

SuburbanTool Inc Well for example one day, I wood like to make a fly fishing reel, but for now, I want to make a simple right angle aluminum bracket 3 inches by three inches, 1/4 thick and mill four adjustable slots in it so I can mount a depth sounder transducer on the back of my boat.

[@MouwDown]

I believe telescoping gauges are more accurate with smaller bores. I can a good feel with them compared to id mics.

[@crossthreadaeroindustries8554]

Thanks for the great share, smarter now.

[@SuburbanToolInc]

Your welcome

[@braddles345]

Very helpful! Thank you! Brad

[@ryanb1874]

Is it more easy for proper feel using giant mics, on very large parts with the typical anvil and ply get diameters?

[@SuburbanToolInc]

You must be very careful large or small.

[@paulmeynell8866]

When you say “a couple of tenths” is that a, one thousandths of an inch divided by ten? As in half a though wound be five tenths? 0.001 = one thousandth. 0.0001. = one tenth ?

[@SuburbanToolInc]

Yes, in this case we are talking about 0.0001", thanks for watching.

[@canamrick]

I've found that a bigger radius on the ends of a telescopic gauge gives a more accurate reading. cheap imports have small radius. they are junk. I've seen Starrett with a smaller radius also. any opinion on this? I rarely use my small hole gauges and felt uncomfortable using them... your technique will help me become better at using them .. thank you

[@SuburbanToolInc]

I'm glad to have been able to help! Thanks for watching.

[@markrichardson239]

I just got my first set of Starrett small hole gauges... 1/2 ball... Wow. I am close, but I will fixture the part like you say. Oh, I gotta be within .0003"... but the job has demands... Don, I love your videos. Could you do one explaining why nobody else could ever set my micrometers for me? They refuse to believe me. Thanks! Mark

[@PreciStrike_96]

can you please make a demo of how to use the cadillac gauge to the left of the surface plate. we don't have one in our inspection room at work, and its been a while since i've last used one. Thanks, Randy B.

[@SuburbanToolInc]

+Sandman Actual Will do. Thanks for watching.

[@PreciStrike_96]

Thanks, much apreciated

[@mmheavyconstruction3148]

What type of camera / lense (s) combination are you using

[@AnuragSharma-xw3ty]

Why not use a bore gauge with dial?

[@stuarth43]

well these telescopic gauges are a hell of a lot better than digi vernier

[@kurtfromMichigan]

I miss working with the guys from the old school like Mr Bailey. Is Suburbon Tool hireing? Haha. I can match his telescope skill and show him a few things about Jig Grinding (haha)

[@SuburbanToolInc]

wonderful

[@theslimeylimey]

I miss tenths. I live in a thousandths world now and its just not the same.

[@ashokp1358]

There is any other way than measuring telescope gauge with micrometre

[@barrobby1]

Hello, what pointers could you provide to someone in the market for a garage sized surface grinder (used). My concerns would be the ways, spindle and other areas of concern I may not be aware of. Could handle a machine of a ton or lighter but something that might be a

[@SuburbanToolInc]

barrobby1 I would recommend a Harig 6 x 12 surface grinder.

[@txkflier]

I don't see any point in measuring the length of the bore gage with a height gage. It'll take too long to find the longest distance, it you ever do find it. I used to measure bores using two precision balls and a set of gage blocks. Sometimes the bores were tapered and I used trig functions to calculate the end diameters and taper.

[@meocats]

How do you measure something like a 6" bore?

[@SuburbanToolInc]

meocats You could use the telescoping gages. Inside micrometers , electronic height gage, Bore gage. It all depends on what tools you have to work with.

[@dougankrum3328]

+meocats ...Inside micrometer...

[@AnuragSharma-xw3ty]

Use a bore gauge with dial, there come in lot of sizes and measure it with micrometer

[@wildcatmahone-md6me]

My advice on measuring small holes within tenths, don't screw around with these type of gauges. Instead get a set of tenths gauge pins and be done with it. Don't forget cylindricicity has a major effect on measured size.

[@barrobby1]

Woops, a machine that be a brand to look for which might be a good utube video to put together. Thanks.

[@garymajor2463]

basics of OD grinding

[@toolguybak]

Excellent video--thanks for posting! (Don--was that you in the ice cream shop on Woodward Ave last weekend?) =Brian=

[@SuburbanToolInc]

toolguybak Yes Brian , that was me but I did not eat any ice cream.

[@toolguybak]

SuburbanTool Inc I wasn't sure. I was in the booth next to you, by the door. Thanks again for these great videos!

[@SuburbanToolInc]

Thanks for watching Brian

[@TankBuilders]

Excellent video but a "mike" - it's a micrometre or to those familiar with that other form of English, a micrometer.

[@SuburbanToolInc]

yup !!

[@thetoecutter13]

It's a mic. If you worked with one everyday you would call it a mic too. Nobody says "I have to Micrometer that part". They say mic it.

[@dougankrum3328]

...6:30....'roll-pins'...? Aren't those actually 'dowel' pins...?

[@sahkram]

i really object to the word "art", tool making is the "craft" of applied mechanics. this is learned through an apprenticeship that includes both practical hands on labor, and scholastic efforts. learning to use telescope and ball gages are part of the craft not an art. I will add that not everyone has the "aptitude" to learn the skills especially the manual part.

[@SuburbanToolInc]

sahkram We view this as the left brain right brain scenario. You are correct that this is a craft. To take it to the next level sometimes requires that creative side of your brain though. That is why we believe there is some art form involved.Thanks for watching.

[@shellyalibangbang3314]

pls make ur video shorter i don't have time to watch the whole thing... maybe u need to crop some part.. u are expert and good teacher but much better if u make it shorter