I had nothing on the ac panel. No lights, fan wasn't kicking on. I watched your video. Went out and pulled and tested a the fuses and the relay, plugged it back in. Tapped on if a few time for good luck and BAMO! Cold air again in the heart of TX! Tanks man!
@pantherplatform3 жыл бұрын
The dude abides!
@sagemodemason9722 жыл бұрын
Hopefully this works for me
@jeffduphily80572 жыл бұрын
Very knowledgeable he just doesn't point the fuse out but he runs through the the circuit making life much easier for me thank you
@cindyterry44792 жыл бұрын
Fixed it! Thank you so much for the video! Saved my parents a lot of money since it didn't have to go to the shop!
@kennetheady1347 Жыл бұрын
😊 now that's how you break it down. Thank you for sharing.
@Joeelectronicschematicsforauto4 жыл бұрын
You were right on your electronics was well prepared an informal great video great electronics explanation I love it
@chesterrathbun2817 Жыл бұрын
Thanks guy that puts me in the right direction. Thank you.
@traxxasrcfun4 жыл бұрын
Great video, very informative
@martinpazderАй бұрын
Thank you very much Lehew , you saved me a lot.
@ogjackson12222 жыл бұрын
This man is a genius thank u fixed
@timknapp63882 жыл бұрын
fantastic info. could not figure out why mine is not working for a police interceptor. Thanks to you, I see i am missing the diode. I will find one and replace. great video
@samueldezalez6144 Жыл бұрын
Did it fix it?
@timknapp6388 Жыл бұрын
No, it did not. I believe there is a computer issue with it. After many tries I took it to a shop and they couldn't figure it out either. My son left from Colorado to South Carolina and he said it would work if they had high humidity. I could jump 12v to the fuse and it would engage the clutch on the compressor and blow cold air. He has since been deployed to Japan and the car is sitting in S. Carolina. Good luck!
@samueldezalez6144 Жыл бұрын
@@timknapp6388 thanks!!
@merrillschaps23252 жыл бұрын
I have a 2007 Lincoln Town Car that the A/C system stopped working immediately after I changed the valve cover gaskets. I have ran tests on all the A/C fuses, relays, and high low pressure switches only to have found they're all good. The A/C system is fully charged without any leaks. However, I am not getting the PCM to ground at the A/C clutch relay. I think the PCM thinks the engine is either overheating or the outside temperature is too cold to turn on the A/C because the cooling fan will not turn on high at all and the cooling fan is only a few months old bought from a Ford dealer with the cooling fan module attached. Any ideas what can cause this or what I may have forgotten to plug back in? Everything else works except the A/C.
@karditzas3 жыл бұрын
I have a 2008 crow vic p71. Replaced ac compressor pulled vacuum, but no joy. Clutch will not engage... checked fuses and relay good. You mentioned if no refrigerant clutch will not engage ... how do you by pass this to get refrigerant in?
@Jessie-if7dx3 жыл бұрын
Any idea what is causing the AC Clutch Fuse #11 to blow once the AC is turned on?
@julianelson50669 ай бұрын
First I lost power to my control panel as well as the direction indicator on the mirror, next the ac compressor went out so we put in a bypass pulley. Still no power to either item. I’m going to recheck the interior fuses and the ones under the hood plus the relay… anything else I should check. I went to oriellys to have the codes read last week and they couldn’t get the code reader to communicate with the computer in the car. I’m at my wits end with this car and it’s only getting colder here in northern Minnesota. Any help is appreciated!
@mk4519933 жыл бұрын
hi doing man I have a 2011 crown victoria I need your help my ac is blowing some sorta cold but I feel not fully cold when I bought last year it i was way cold but now I checked the refrigerant and it is full so not sure where to look any recommendation thanks
@jimchance50063 жыл бұрын
I've got a super weird problem with my AC. It was running just fine the other day, but yesterday my car overheated and the ac wasn't working. I tested the thermostat and found it was bad so I replaced it. The overheating problem is fixed, but the ac isn't working right. At an ambient temperature of 97 degrees, the AC blows at 95 degrees. For reference, the vent setting blows at 105 degrees. Also the AC lines are not getting cold at all.
@tomashernandez1598 Жыл бұрын
Also I believe the a/c and or Max A/c setting wire harness goes to the low pressure switch and from that switch to the PCM that is how the PCM knows that you asked for A/C then the PCM will ground the control side of the clutch relay.
@sayed-troll64453 жыл бұрын
My friend I need help I have Ford Marquis 2006 some how after I cleaned my car my A/C went so crazy that turns on automatically and off then it went more crazier it start to turn on /off with non stopping and slow my engines
@2LitProduction3 жыл бұрын
What do we do if the a/c isn’t coming on at all? Is that a fuse issue?
@owenhill4309 Жыл бұрын
Can the a/c work without a AC diode???
@DeestarMusic553 жыл бұрын
I need to know this about a 96?
@FrancisJFox11 ай бұрын
What about my compressor short cycling every 3-4 seconds. Turns off - turns on - turns off - turns off. What do you think that is?
@Palmyj073 жыл бұрын
I went and had a new battery put in and all of sudden my ac quit working , would you know why ? 2006 mercury grand marquis
@Mike-jf4kf10 ай бұрын
I was parked engine running and AC on, then it all stopped, no power to controls , so it all just stopped, I can turn my AC controls on and off and I get nothing, what else to look for, check all fuses and relays, replace with new ones, still AC won't turn on, I have no power to my controls, what can I do, I need help
@FrancisJFox11 ай бұрын
I tried adding refrigerant & the gauge increases when the compressor turns on & drops down when off , etc etc…
@ivannaortiz3651 Жыл бұрын
Hi yesterday I replaced the instrument cluster on my crown Victoria and now the a/c compressor doesn’t turn on please help
@dumbmonk80472 жыл бұрын
If it has way too much charge will it also shut it off to protect it?
@tommykennedy88863 жыл бұрын
Very helpful thank you:))
@greensnmachines Жыл бұрын
3:51 is it common for that pressure sensor to go bad? If it needs replacing, does the AC system need to be evacuated?
@skipwilliams728811 ай бұрын
No. Just back it out and put a new switch in. When you take the old sensor out, it will self seal.
@mariot37084 жыл бұрын
Great video, well explained. Keep ford videos coming, 03-20 vehicles preferably! I do have a current issue with my marauder. A/clutch engages but blower motor wont turn on. All fuses under dash good. Any suggestions??
@LehewTech4 жыл бұрын
I would check the connector to the blower motor (somewhere underneath the glove box) for burnt pins or corrosion. You can also tap on the blower motor and check to see if its getting power and ground
@saad29882 жыл бұрын
You just saved me 200$ you are boooooosssssssss Thanks a lot
@marquesebrown6783 жыл бұрын
My clutch sounds like it works at does a thing where it comes on and then it stops and then it comes on again repeatedly in that order and will not blow cold even after recharge ? What could that be, and or mean ?
@eljp41753 жыл бұрын
I have the same issue, already replaced AC clutch relay and does same thing 🤔
@Nicksanders3863 жыл бұрын
I got a 2000 crown vic and the air blows hot as hell. The compressor turns on and the lines get cold but the air never gets cold. Any idea what is wrong?
@CobraR19933 жыл бұрын
Your blend door is stuck
@TexCynRVLife4 жыл бұрын
Thank you! I have a 2003, I will try your tips. 👍
@tonysully12 жыл бұрын
Do 2009 Crown Vic have an ac diode too? Does any one know what years had the ac diode?
@ronalddaub5008 Жыл бұрын
My o4 has one diode I'm testing it and it won't take power either way.
@slingblade313 Жыл бұрын
Will it work without the diode? I got my car back from the shop for a brake job and my AC which used to be cold enough to freeze a steak is now blowing hot air, and I checked everything and noticed the diode is missing 🤔 maybe some scumbag mechanic has sticky fingers?
@owenhill4309 Жыл бұрын
Wondering the same thing as mine is not there also
@johnvradenburg1924 жыл бұрын
could it be possible a check engine light caused by a misfire cause the a/c to not come on?
@LehewTech4 жыл бұрын
Yes, absolutely.
@johnvradenburg1924 жыл бұрын
@@LehewTech guess I'll be looking into that tomorrow then
@johnvradenburg1924 жыл бұрын
@@LehewTech fixed the misfire but still don't work but now I can get it working if I bypass the relay but it doesn't if I swap with a good known relay🤔
@anthonyryan77013 жыл бұрын
I have a 2010 crown vic. The ac worked when I first got the car. It suddenly quit working shortly thereafter. My compressor is working and clutching. I replaced the smaller black relay. I replaced the diode and checked the other 2 15 amp fuses which are fine. I've also recharged the system to be certain there was enough refrigerant and the accumulator appears to be in good condition. Still blowing hot. Any suggestions? If the large gray relay is bad would everything still work?
@LehewTech3 жыл бұрын
If the compressor is engaging that begs the question: are the ac lines by the firewall getting cold? If so, and you have heat coming out and not AC, the blend door may be stuck in the hot position
@anthonyryan77013 жыл бұрын
@@LehewTech Thanks! I will check this as a possibility.
@officialsouthsoul5223 Жыл бұрын
@@anthonyryan7701did you ever figure it out?
@CoastieLenn2 жыл бұрын
How common is it that the PCM goes bad? I’ve got good charge, switches, fuses, relay, compressor, and clutch, yet I still am not receiving a ground signal to the compressor relay. The AC works for ~5-7 seconds and then stops blowing cold. (2003 Marauder)
@keenankircher74922 жыл бұрын
I may have the same problem , a shop just diagnosed a bad pcm , my ac doesn’t work at all but it fixed itself for like a trip to McDonald’s and quit again
@CoastieLenn2 жыл бұрын
@@keenankircher7492 a friend of mine basically bypassed the PCM signal to the compressor clutch. IDFK how he did it now since I sold it about a year ago, but he basically wired the pressure switches to the signal wire to the CCM and then independent ground for the switches as well. Worked great for a long time but I have no idea what the long term ramifications are of that.
@keenankircher74922 жыл бұрын
@@CoastieLenn well I already ordered the pcm , if it doesn’t fix it I’ll return it and figure something out
@MarzMindset3 жыл бұрын
Watched your video was able to get a missing horn and all three levels of my ac back from only being able to use ac on highest blower level and I can switch temperature but I cannot use the medium and lower setting why is that
@LehewTech3 жыл бұрын
You may have a bad blower motor resister
@MarzMindset3 жыл бұрын
@@LehewTech thank you. Do you know where one can purchase these resistors
@LehewTech3 жыл бұрын
Online or a local parts store.
@B711HD3 жыл бұрын
I have the same problem
@74keefg634 жыл бұрын
Thanks ....I'm not sure if this is my problem but I have something to look for...my clutch is spinning my refrigerate is full...but it's not blowing cold ...my fan wasn't on 🤦🏾♂️🤦🏾♂️🤦🏾♂️its driving me crazy
@obadiahisrael71924 жыл бұрын
Did u figure it out having same problem on a 04 crown vic
@dougstewart90934 жыл бұрын
Great info. I've got a 2003 and the A/C cools great but after I've been driving and shut it down it does not want to come back on or there is a long delay (5-10min) before the A/C clutch will engage.I was working on checking all of the switches to see if any of those needed replacing including a WOT Cutout switch which I'm told i have yet nobody knows where or how it works. I've got refrigerant so i don't think the powertrain module would be preventing it from engaging and it's not overcharged. Any suggestions what else i can check?
@dougstewart90934 жыл бұрын
BTW, I also checked the relay by both tapping and swapping but that wasn't the issue. It's also a CNG car which i don't think matters.
@LehewTech4 жыл бұрын
Yessir! First few things I would check is if the check engine light is on, if there are any stored trouble codes, if the coolant level is good and if the engine overheats at all. If all those things check out there are a few likely problems that come to mind. Relays are more likely to fail as they heat up. You could try swapping the relay when this problem is occurring. There could also be a problem with the clutch on the ac compressor where it fails to lock up when it gets hot. If the clutch is receiving power but not engaging then it needs to be replaced. Good luck!
@dougstewart90934 жыл бұрын
@@LehewTech Thanks. A/C clutch seems to work great, and when i say hot i don't mean hot to the touch, I'm talking 80° plus outside. Refrigerant levels are good as well. I grounded the lead that comes from PCM and the A/C kick on which tells me the PCM is having an issue. The car has only been running for a few minutes so it's not overheating, could it be a bad temp sensor that falsely telling the PCM the car is overheating?? There is also the High Pressure switch on the A/C High Side but that has 3 wires and I cannot find a schematic showing which wire is which. Thanks for your response and if you have anymore input regarding this new information I'm all ears.
@malonebonestir3 жыл бұрын
it overpressured due to the fan not spinning I think and started releasing freon through the mechanical relief valve on the compressor.
@jimchance50063 жыл бұрын
I think that may have happened to me! My fan assembly went bad and my car overheated. It cooled down, and I plan on replacing the fan, but the AC does not work anymore. How do I test if this is the case?
@projectp71652 жыл бұрын
I’ve tried everything in your video and still have nothing… new accumulator, and two bottles of refrigerant later, still nothing.. no leaks, but I checked my Freon level and it was at 0 psi.. I’m out of ideas.. ford dealer wants almost 300 to check it
@MalikBaggz4 жыл бұрын
My 2008, only blowing hot air any tips?
@traxxasrcfun4 жыл бұрын
Probably the gate that switches from hot to cold air
@ronalddaub5008 Жыл бұрын
My o4 s fuse box is not laid out like that. My speedo oil pressure gauge. And compressor stopped at the same time My oil pressure gauge has been messing up a while. Did not lay All the way down and stay there until today. Ac did work . A few days before. This one will take some troubleshooting my diode is there but no other diodes next to it I know how to check a diode and it should take current one way this one is not
@malonebonestir3 жыл бұрын
2005 VIC compressor clutch engaged with ac switch off, whats going on?
@LehewTech3 жыл бұрын
The relay could be stuck or the clutch could be stuck.. does it remain engaged when you remove the AC Relay?
@malonebonestir3 жыл бұрын
@@LehewTech with the ignition switch on, engine off and the ac switch off I can unplug the compressor at the compressor and It will disengauge.
@malonebonestir3 жыл бұрын
it overpressured due to the fan not spinning I think and started releasing freon through the mechanical relief valve on the compressor.
@malonebonestir3 жыл бұрын
sounds like a relay stuck
@malonebonestir3 жыл бұрын
thanks!
@zac.bolin013 жыл бұрын
There’s a connector in that pressure sensor area that isn’t hooked up on my car… I’m gonna look more into it at sunrise
@malonebonestir3 жыл бұрын
with the ignition switch on, engine off and the ac switch off I can unplug the compressor at the compressor and It will disengauge.
@kyleburke80252 жыл бұрын
They dont have the same fuse layout throughout the years. None of this is the same on my 03 vic
@ronalddaub5008 Жыл бұрын
Yes my 04 has only one diode
@pongothecrownvic4742 жыл бұрын
When you said check to see if horn works I said uh oh. Friday I replaced alternator then my horn stop working and back right window stop working