Solidworks: Section, Detail, crop views and material selection

  Рет қаралды 6,502

Eli Chmouni

Eli Chmouni

Күн бұрын

A lecture explaining the rules of section views (full section, offset section), plus detail views, material selection, crop, breakout, etc...
Created by Eli Chmouni

Пікірлер
@Varun-uv4li
@Varun-uv4li 6 жыл бұрын
Please make more vedios on solidworks !!
@manuellando2060
@manuellando2060 8 жыл бұрын
Thanks!
@alnooree2000
@alnooree2000 11 жыл бұрын
thanks
SolidWorks: Revolves, Sweeps, Trim, Convert, Offset, CSWA
43:59
SolidWorks: Revolves, Sweeps, Trim, Convert, Offset, CSWA
Eli Chmouni
Рет қаралды 18 М.
Solidworks: Dimension a Drawing Sheet
30:18
Solidworks: Dimension a Drawing Sheet
Eli Chmouni
Рет қаралды 208 М.
REAL or FAKE? #beatbox #tiktok
01:03
REAL or FAKE? #beatbox #tiktok
BeatboxJCOP
Рет қаралды 18 МЛН
VIP ACCESS
00:47
VIP ACCESS
Natan por Aí
Рет қаралды 30 МЛН
СКАНДАЛЬНЫЙ бой Али, когда в ринге ему противостояли сразу ДВОЕ #shorts
01:12
СКАНДАЛЬНЫЙ бой Али, когда в ринге ему противостояли сразу ДВОЕ #shorts
BalcevMMA_BOXING
Рет қаралды 1,2 МЛН
Enceinte et en Bazard: Les Chroniques du Nettoyage ! 🚽✨
00:21
Enceinte et en Bazard: Les Chroniques du Nettoyage ! 🚽✨
Two More French
Рет қаралды 42 МЛН
Lofts and Airplanes in Solidworks
19:19
Lofts and Airplanes in Solidworks
Eli Chmouni
Рет қаралды 150 М.
Solidworks: Equations, Configurations, Mass Properties, Coordinate Systems
14:10
Solidworks: Equations, Configurations, Mass Properties, Coordinate Systems
Eli Chmouni
Рет қаралды 27 М.
How to Select the Right Material During Design | Design- Material Selection in Mechanical Design |
14:47
How to Select the Right Material During Design | Design- Material Selection in Mechanical Design |
Balasaheb Khalekar
Рет қаралды 18 М.
Solidworks: Creating an Assembly and an Assembly Drawing Packet
50:40
Solidworks: Creating an Assembly and an Assembly Drawing Packet
Eli Chmouni
Рет қаралды 11 М.
Steep and Shallow Deep Dive!
38:39
Steep and Shallow Deep Dive!
Toolpath
Рет қаралды 1 М.
Build a POWERFUL Winch with a 12 Volt Motor and Old Sprocket in 24 Hours!
19:42
Build a POWERFUL Winch with a 12 Volt Motor and Old Sprocket in 24 Hours!
King DIY
Рет қаралды 14 М.
SOLIDWORKS Tutorial - Drawings Tips and Tricks
51:53
SOLIDWORKS Tutorial - Drawings Tips and Tricks
GoEngineer
Рет қаралды 322 М.
Matlab: Lecture 1
52:55
Matlab: Lecture 1
Eli Chmouni
Рет қаралды 147 М.
SOLIDWORKS 2024 is here and it's awesome!
51:15
SOLIDWORKS 2024 is here and it's awesome!
SolidWorks With Aryan Fallahi
Рет қаралды 74 М.
System Dynamics: Systems Thinking and Modeling for a Complex World
55:58
System Dynamics: Systems Thinking and Modeling for a Complex World
MIT OpenCourseWare
Рет қаралды 270 М.
REAL or FAKE? #beatbox #tiktok
01:03
REAL or FAKE? #beatbox #tiktok
BeatboxJCOP
Рет қаралды 18 МЛН