Lesson 5- How to make tags for Siemens PLC in Ignition SCADA

[@ОлегКаюк-е2м]

you have the best video lessons on ignition. please keep making videos on ignition!)

[@thegeterrdone]

Thanks for the compliment ;)

[@marcoreyes2763]

Excellent explanation. Thank you very much for tutorial. Will you upload the second part to add DB?

[@travisbutler2014]

Very nice video, I had my tags linked and working within a few minutes of following along.

[@thegeterrdone]

That's great :)

[@ansonkiek6471]

hi I have compact logix studio 5000 plc , customer is using ignition. I check your video ignition can directly read the plc as long the setup opc built in for ignition. So my side not need do any software or programming ? Just connect and browse the plc tag through my plc Boolean or any tag right ?

[@thegeterrdone]

If your PLC supports OPC UA then you just need to activate that and then you can browse the tag from Ignition SCAD.

[@sohaibamjad9060]

i have one question why the input value tag cannot change state from ingition scada hmi while if you write memory bit in program that tag chnage value state in scada hmi. e.g i0.0 not working in scada while m0.0 button work and state is chnaged when u presssed. please advised

[@ryanalcantara5336]

Hey Rajvir! Thanks for the informative video! is there any way that I can add siemens tags without using ignition designer?

[@thegeterrdone]

I think you have to use designer. But what’s your objective behind this?

[@gbengaoyede2877]

Thank you rajvir singh for this great opportunity to learn from you ❤️

[@thegeterrdone]

You are more than welcome :) Where are you implementing the Gaines knowledge ?

[@jcc1219]

Goods lessons! I have a question: How to write an string variable from ignition to PLC siemens 1200??? Thank you some much!

[@thegeterrdone]

I have not tried yet but you can write directly to a tag (datatype String) in Siemens PLC. Is it not working for you?

[@quoit99training83]

What is the “Free Trial Version” as mentioned in one of your slides? Thanks for the video :)

[@electromecanica_automatismos]

Well done bro.... by the way: if I have several variables in my PLC (S7-1200 or S7-1500)... aproximately 500 var ...Do we must be to do every action like your video?

[@thegeterrdone]

Thanks, I would say you should put those variables in an array and then read the whole array in SCADA. This will save your network traffic :)

[@oyetoroahmed5584]

Is it possible for tagging, building of working Scada to work without connecting PLC?

[@thegeterrdone]

Yes it is possible. In my channel you will find a video which explains the steps :)

[@shavazmunir4604]

Sir, can you tell me which JAVA file should be downloaded and installed? Please share the link.

[@thegeterrdone]

Java 8 runtime

[@alonsohdzf]

Awesome content!

[@thepowerbits2845]

i DID IN MY DESIGNER LIKE YOUR LESSON, BUT WHEN I PUT [SIMATIC]MX0.0 THERE IS A MISTAKE, WHAT CAN BE WRONG?

[@thegeterrdone]

Did you enable PUT/GET permission ? Check if you have subnet enable as well in your plc

[@rajsoparia3118]

@@thegeterrdone same issue for me too. ihave enabled put/get

[@darppatel9550]

Is it possible to do this without having actual PLC?

[@rajsoparia3118]

the tag that i made says "uncertain initial value"

[@atrbulldog5955]

What was the point of making those variables in lesson 3, we never used them?

[@rangaswamy8604]

Please do a lesson on connecting the scada to MySql database.

[@thegeterrdone]

I already have this lessons in my learn scada from scratch course.

[@rangaswamy8604]

@@thegeterrdone Will the course include creation of tables from within / outside ignition and MySql commands?

[@rajeevgarg3559]

Hello sir please reply my tag address is showing bad 😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢😢 please reply

[@ОлегКаюк-е2м]

Thank you

[@bapihazari6556]

Plzz make a Hindi lesson.

[@sohaibamjad9060]

please reply