Lexus GX460 SHARK FIN ANTENNA REMOVE AND REPLACE

Roof top antenna banged up on your Lexus and you're too afraid to conquer it yourself? Have no fear, grab a 10mm gear wrench and knock it out in 30 minutes. Good luck !

[@AFOdada]

Thank you Bob! I backed my 2020 GX into my garage for the first time, not realizing the shark fin didn't have clearance of my overhead storage rack. The whole cover got knocked off! The first thing I thought of was you, and if you had a video covering a shark fin installation. It took me about an hour and a half because I had to bend the inner liner of the shark fin back into place and piece the whole antenna back together. The roof was slightly bent but I was able to level it out. I used a little clear silicone to make sure the antenna stays watertight. You are DA MAN!

[@GXBOB]

On a 2020? That must’ve hurt. I know a good lawyer if you want to sue your wife for buying a house with a garage without considering you own a 2020 Lexus. Very inconsiderate of her.

[@Donorcyclist]

Great info. Details like the three tabs' directions make this tutorial gold!

[@GXBOB]

Thanks. I explain the way i want people to explain things to me!

[@84runner]

Thank you thank you! My wife's 460 has been popped loose for months! Thanks for listening to our requests! I can't BELIEVE Lexus only relies on 3 little prongs to secure antenna! Of course you don't want it strong enough to damage roof! Can't wait to tear into it!

[@GXBOB]

I know i said the loosening of the 10mm and disengaging the plug is done blindly, but there is enough room for you to stick your arm in there and visually see what you're doing. It was just challenging for me because of the camera angles. You will definitely have an easier removal than i did.

[@84runner]

@@GXBOB I was thinking the same thing! Thx!

[@drevo400]

2013 GX460 shark fin antenna was easier to replace and disconnect. Your video was helpful.

[@GXBOB]

how much easier than screwing one 10mm bolt, right?

[@GX46070]

Thanks for another great video Bob! For anyone else who attempts this: I found that using a short stubby ratchet with a small 10mm, to be easier to use on the bolt than a ratchet wrench. I used this video to install the Go Fast Campers fin delete for the 4Runner, it fits the GX as well.

[@GXBOB]

Nice, thanks for the input!

[@PeterKinsey]

@gx46079 I have a 2011 GX… Will the GFC 4Runner shark fin delete fit my rig? I want to add the front runner table to my rack and it mounts under the rack. I’m looking for a way to get it to work? I basically need to either shave the fin down or install the gfc or can I just remove it and install the MVT delete which is just a couple of washers and a nut that would keep it water tight? What exactly is in the antenna? Could I just 3m tape it up inside the headliner?

[@GX46070]

@@PeterKinsey GFC 4 runner delete should fit your ‘11 GX, I can’t see why Toyota would have changed the fin with the facelift in 2013… That said, it takes less than 10min to pop the fin out using Bob’s method, to confirm if it’s the same as what’s in the GFC install video, and you can always put it back in. Better than destroying it to take it off. My use case was the same as yours, to mount my FrontRunner table under my rack. It’s worked out great. I still don’t know what the antenna is for, but haven’t noticed any difference after having it off for many months. (I don’t use satellite radio)

[@weiz4944]

Thank you so much! I just broke my antenna today, ordered the new one from dealer. I am going to do it myself.

[@GXBOB]

Glad it helped

[@grantcarroll5696]

Thank you for the video! One of the best DIY videos.

[@GXBOB]

With the beer or without?

[@michaelnadle310]

Thanks for making such a great video. Step by step easy to follow instructions. 👍

[@GXBOB]

You can pay me with beer.

[@davidc977]

Thats impressive...my fin got knocked off ..everything still works.. I just bought aftermarket fin that was large enough to cover the chip. 3m tape didn't work. I had to use silicone unfortunately. It worked though.

[@jg-365]

You did it!!! Thanks a lot - instant hit. A lot easier than I expected since you don’t have to mess with the sides.

[@GXBOB]

I was expecting to drop the entire headliner to be honest.

[@jg-365]

@@GXBOB needless to say, I love you more. Haha

[@jg-365]

Mine was different on a 2010 GX, I believe it uses an 18mm nut to hold the ring that presses against the roof. Not user how tight to go with it, though.

[@geodes4762]

This really helps me! I have a 2021 RX350. Basically the same procedure. I had one insurance estimate and it was $2500.00! They tried to tell me the whole headliner had to come down. They have to check the beam underneath for damage and then remove the roof racks so they could redo the whole area around the fin! Told my wife I’m going to do it myself. Total parts $175.00 and about 45 minutes work. The small dimple near the fin I’ll massage out with a spoon. Any possibilities of leaks will be siliconed. Crazy!

[@GXBOB]

I really love hearing stories like this. Not sure how many more GX vids you can use for the RX but at least you’ve helped others answer at least one potential question. Enjoy!😃

[@halfman7869]

Hi Geo Des, Did you have to remove the dome light like GX model?

[@petethehandyman9185]

Awesome video! Thanks so much it was a Huge help!!

[@GXBOB]

With a name like Pete the handy man, I seriously doubt you needed my video.

[@JEMMATED]

Thank you

[@marcbergman312]

Thank you!

[@GXBOB]

You’re welcome Marc!

[@mikescool]

Thanks for the video! I bumped the fin against my garage door. It's slightly loose but not broken, the radio still works. Just wondering if i need to seal the gap with silicon? I can move the fin around if i press on it, although it's not super loose i can see a small gap in the front.

[@GXBOB]

Yes you should remove it entirely and reseal with a new rubber gasket. The minute you hit that garage, you created a nonconformity on the outer mold line of your roof.

[@edfairley8347]

Happy Father’s Day GBOB!

[@GXBOB]

Happy Father’s Day to you too Ed. 🍷

[@robertdutka3409]

Hey Bob! Great video, but I'm disappointed there wasn't any typical GX Bob humor in this video which I look forward to seeing. Maybe next time. 🙂

[@GXBOB]

I only act like an idiot after every 2-3 vids. You have to remember my parole office and my exwife's legal team is following me on YT.

[@Ken-lp5zv]

Have you done a 2021 highlander or newer using this method. I see a seat belt in the ceiling that I cannot seem to take out. I can take out the lights etc no problem.

[@GXBOB]

I can't say that i have. Sorry.

[@MultiCapriccio]

The shark fin on my 2017 GX was ripped off by garage door when my rookie driver daughter backed out too early and then decided to go back in. The only thing remaining is part of the chip (about 1 inch square) I would like to replace it myself. What kind of silicon should I purchase and when/where should I lay the bead? Love your vids! I really think I can do this!

[@GXBOB]

www.amazon.com/3M-03601-Plastic-Emblem-Adhesive/dp/B000CCM3J2/ref=asc_df_B000CCM3J2/?tag=hyprod-20&linkCode=df0&hvadid=343955370377&hvpos=&hvnetw=g&hvrand=5045313427656445553&hvpone=&hvptwo=&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9031253&hvtargid=pla-524635590405&psc=1&tag=&ref=&adgrpid=74841503648&hvpone=&hvptwo=&hvadid=343955370377&hvpos=&hvnetw=g&hvrand=5045313427656445553&hvqmt=&hvdev=c&hvdvcmdl=&hvlocint=&hvlocphy=9031253&hvtargid=pla-524635590405

[@joesoika2628]

I want to change out my short mast antenna on my 2009 Toyota Venza to a shark nose one I wonder if this factory shark nose will work on my 09 Venza.

[@GXBOB]

There’s only one way to find out. Do it. Great thing about Amazon is everything is refundable

[@lexcastillo2768]

I tried doing this on my 2010, and there was a whole thing between the headliner and the metal roof. It was so much harder to pull the headliner down, I really couldn’t even put my hand in there it was a lot stiffer and tighter in there. I couldn’t do it.

[@GXBOB]

You might have to drop the side plastic quarter panels on the older years.

[@joycelao7153]

Hi, Bob, thank you so much for your video, it helps to understand how this process work! I do have a question, after you replace the antenna, can we go do car wash as normal as before? I was wondering if the water will get thru the gap of the antenna since there isn't any glue or rubber seal to secure the shark fin cover? Please be kind enough to advice. I recently had the dealership to replace for me and the advisor was saying it show be ok but won't know till it if gets thru a good rain? Your expertise is greatly appreciated. I really need to get the car washed... kinda dirty.😀

[@GXBOB]

Depends…why did you have it replaced? Accident backing your truck in the garage? If your antenna was struck then the contour of your roof was probably affected even though you can’t see it by the naked eye. I feel like anything that’s taken off after the manufacturer had their robots installed never really goes back the same anymore especially exterior components. I suggest you lay a bead of silicone where the antenna makes contact with the roof of your Lexus just to sleep better at night. Nothings worse than water damage. Rectorseal 57500 10.1-Ounce Hi-Temp 100-Percent Rtv Silicone Sealant is a good exterior sealant for water proofing on paint that’s recommended by others.

[@joycelao7153]

@@GXBOB Thanks Bob for your quick reply! Yes, i did have my garage door yanked the antenna cover off. But the actual antenna was still sitting good but a bit crooked on the top. However the shark fin cover could no long letch on properly and dealer suggested to replace the whole thing, which I did. They put it back and it looks find and I did ask if they seal it up, they said it doesn't need to be sealed it is just a screw to secure it ( just like the way you show on your video). So I was wondering if i should be worrying about the water leaking in ? Maybe I m paranoid ...I should wait till it rains once to tell? Thanks a million again.

[@TOGC]

Damn, my 2013 looked totally different when I did mine. Guess they changed it on 14+

[@GXBOB]

i can not confirm or deny but i would hope that they continue to progress in design and technology as each design changes.

[@andrewfox9000]

Hi Bob I appreciate your videos they’ve cost me my time and money;) If you catch this comment could you address the globe box latch? Mine seems to function properly however it’s not very secure. A minor annoyance. I’m sorting a few issues with my new to me 10’ GX and have done a number of your mods. Seat covers and rear window regulator are waiting in boxes. Many thanks for what you do. Andrew

[@GXBOB]

Yo Andrew, glove box is easy. Just involves a bit of tinkering. But rear window regulators??? Now we're talking. As far as seat covers, how did it go? I may do another one but one with more steps and better camera angles. My equipment and editing skills have improved significantly since.

[@andrewfox9000]

@@GXBOB it’s burning hot here in Fla Bob I’m building fortitude before I sweat my ass off changing those covers

[@GXBOB]

@@andrewfox9000 We are not too far behind in temperatures in So Cal. The days are longer and we are starting summer tomorrow as i type. I'm looking to find shade so i can continue in my quest for additional videos to accommodate a long list of requests.

[@ericbromley3532]

Bob, old car (2012 GX460) and new-to-me house/garage. Factory antenna is 2" too tall for garage. Know of any lower profile alternatives or straight up flush caps?

[@GXBOB]

you're not the first to request this Eric. There is a cap cover online that 4runners are using but it does fit the GX460. If u still want the antenna function i'm sure you'll find a way to tuck it within the headliner but this cap will remedy your issue. Good luck and may the force be with you. forum.ih8mud.com/threads/gx460-roof-antenna-shark-fin-cover-delete.1246373/

[@kylemetzger1046]

Hi, Bob - it seems as though mine got knocked loose in a car wash (won’t do that again). Do you think I could simply pull down the headliner and tighten that 10mm bolt to help reseat it without completely removing it and reinstalling it?

[@GXBOB]

Since it’s been detached off its original mounting location it might be a good idea to buy a new rubber seal or use aftermarket seal around perimeter.

[@kylemetzger1046]

Thanks!

[@Kiss__Kiss]

Great Surgery, BOB...

[@GXBOB]

They're not breast implants if you're wondering. I haven't hit the gym in months.

[@Kiss__Kiss]

@@GXBOB Hahahaha!!

[@joes5134]

What kind of silicone would you use to create a tight seal around the new antenna? Any chance of a link to what you recommend? Thanks!

[@GXBOB]

Joe, when you remove your shark fin, i recommend you replace your oem rubber gasket and that should properly seal without the need for sealant. If you feel your antenna or roof was displaced due to weather, accidents, or multiple removals then i highly recommend a product off of Amazon that other experts use for external seals such as. Its a little expensive but i rather pay now than later with water damage: www.amazon.com/Rectorseal-57500-10-1-Ounce-100-Percent-Silicone/dp/B008A3UG8A?ie=UTF8&linkCode=ll1&tag=improvecaraud-20&linkId=3c176fa45af78ef2cd11b431a23bb269&language=en_US&ref_=as_li_ss_tl

[@joes5134]

@@GXBOB Thank you so much! Yea the fin was damaged and pulled up backing out of the garage, so the antenna assembly sits raised due to the bend in the metal. Fortunately the seals are holding for now and there's been no water intrusion but I was wondering if I could replace the plastic cover and then bond it down to the metal.

[@gvkauffman]

Hey Bob, do you ever use regular gas as opposed to premium?

[@GXBOB]

Not in my GX. I’m good with premium to the end. You may save money and mpg's in the short run but the detriment it will cause in your emissions system will cost you thousands later and will eventually worse MPG's.

[@art2lyd12]

Excellent. I like when you talk dirty, "slip hand into the hole" lol

[@GXBOB]

I had no idea i even said that. C'mon man, this is a family channel.

[@art2lyd12]

@@GXBOB, oh listen to you and your 400 in ex. 😆

[@Widemouth1832]

My shark fin was broken. Does anyone know the correct website and part number to buy the shark fin to replace it? I have a 2015 GX.

[@GXBOB]

www.lexuspartsnow.com/oem-lexus-gx460-antenna.html

[@Widemouth1832]

@@GXBOB You are a prince amongst men.

[@Cochi0020]

@GX*BBO do you feel the difference between sport and comfort mode? My father owns a GX 17 and sincerely feel the same in both.

[@GXBOB]

Sorry German, i own a base model and do not have the options of sport/comfort modes. I only have one mode and its spring coils with shocks. If you have the option of adjustable shocks that provide sport/comfort mode then there should be a significant difference since one is a tighter feel and one is a softer feel. If you get to the point where you can't tell the difference, you might want to check your shocks for visible leaks and change them out. I had a 2011 GX premium that had those options but rarely ever used it. I found it to be useless to me.

[@carlosviscarra1]

Do you have an instagram account? I recently purchased a GX460 Premium trim and regret not getting the luxury because of the leather seats. Any thoughts on synthetic leather ?

[@GXBOB]

Yes i do have IG, its the same username as my YT. The IG is mostly random life stuff and not car specific. So leather vs synthetic.....depends Carlos, where do u live, what is your budget, and are u hauling children and pets? Reason why i ask is leather is more durable, smells better, and lasts longer, but synthetic retains its color without fading, a lot easier to clean, and takes the beating of hot climate better. Living in states like Arizona and Texas, synthetic would be a better choice.

[@carlosviscarra1]

@@GXBOB thanks! I am just regretting getting the premium trim instead of the luxury which is about $10k more. I live in LA, with three little monsters.

[@GXBOB]

@@carlosviscarra1 i have had no issues with nuluxe. I condition my seats regularly.

[@jvillasin]

thanks GXBob, another great worthless how to video. I wish you can find a way to get our GX460's run on regular gas instead of premium lol. $$$ gas prices arghhh

[@GXBOB]

Technically you can run on regular. Just make sure you’re going to sell it in a year or so because the engine will be so clogged of carbon, the next owner will be assed out.

[@jvillasin]

@@GXBOB hahaha! i'll keep that in mind ..

[@thegreatone358]

I’m certain ‘worthless’ is not the word you meant to use.

[@jvillasin]

@@thegreatone358 , you are probably new to GXBob’s page. 😉😁🤣

[@deflamrek]

Heil Bob

[@GXBOB]

Whoaaaaa. WWII is over. We might all be speaking Russian or Chinese by the end of the year.