Lexus GX470 - Eibach Pro Truck Lift Kit Install.

[@lexus_offroad_adventures]

If you want more info on how to do the fronts, I made a new video that involved removing and reinstalling the front coilover assembly which may help you out: kzbin.info/www/bejne/f6qvhGN8mpqaeLM

[@lexus_offroad_adventures]

Dang, watching this video again I feel kinda bad about not doing more filming on the fronts. My wife had to stop filming and play with nieces and nephews, and I didn’t want to stop working. Feel free to comment any questions you may have on the front install and I will try my best to answer.

[@CliffCakes]

Looks nice and level! Which front spring perch setting did you go with? I'm about to install this kit this weekend on my GX.

[@lexus_offroad_adventures]

Cliff Huff I have it on the first clip. I wish I went with the second clip but I was sketched out by my cheap spring compressors. It has a bit of front rake so it’s just a bit too low in the front. Don’t make my same mistake, go with the second clip!! And make sure u take before and after measurements from a good point like the edge of the rim. Not doing that was my other mistake.

[@CliffCakes]

@@lexus_offroad_adventures Thank you for the quick response!! I was thinking the second clip as well. I appreciate you solidifying that.

[@robertswiers7851]

Any issues or suggestions for those UCA bolts?

[@lexus_offroad_adventures]

@@robertswiers7851 Pretty straight-forward. You just need to remove anything that gets in the way of you reaching the bolt head. On the passenger side, you can just use an extension I think. On the driver side, you’ll need to remove the battery/battery tray. You’ll also need to slightly bend some body out of the way to extract (not as scary as it sounds you’ll know when you see it).

[@bigtreesfall]

man, great job! this video gives me the confidence to tackle this job myself. thanks a ton!!

[@lexus_offroad_adventures]

Thanks! Good luck

[@hehexd1769]

Thank you so much for your detailed and clear installation video! You helped me install my eibach lift this past weekend! One question, i am still on stock wheels and tires, so the front independent suspension is a bit narrower since the suspension lift. I have noticed some floaty steering at highway speeds, do you think 1.25in spacers like yours would correct for the narrower stance and improve highway stability? Thanks!!

[@lexus_offroad_adventures]

That’s awesome!! Super stoked that I was able to help. I personally run 1.25” Spidertrax spacers and they work VERY well to correct that issue. Highly recommend. I forgot to film an install video of those but just follow the instructions and use the red thread lock they include, you’ll be good.

[@hehexd1769]

@@lexus_offroad_adventures So you experienced this issue too? i am thinking about only running them on the front wheels and leaving the rear without any spacing. I love your channel and thanks for all the info and advice!

[@lexus_offroad_adventures]

@@hehexd1769 really appreciate you watching! Yes I definitely had that issue as well and especially off road, things get a little tipsy. I would recommend running front and rear. You will thank me later. The rear looks way better with the wider stance. It’s not just for the front.

[@hehexd1769]

@@lexus_offroad_adventures well I'm glad to know I'm not the only one. The reason I was thinking just spacers on the front was because the independent suspension is actually narrower after the lift whereas the rear axle is still the same stock width. It might just be flawed logic idk

[@landminehopscotch3617]

@@hehexd1769 did you get the spacers? If so, how do you like them?

[@nicknamean]

Nothing beats putting your life in some excellent made harbor freight jack stands 😂

[@keithk888]

Really great video! So thankful for people like you taking the time to document this stuff esp for ppl like me with little wrenching experience. I was curious, I have an '11 Sequoia Platinum with failed air springs and have been watching GX 470 videos for ideas since 2nd gen sequoia videos air spring videos are rare. I already replaced the OEM electronic back shocks recently, do you know if you could just replace the rear coils on a swap like this? Also, would that affect the ability to switch between sport & comfort settings with the shocks or is that an independent system from air springs? Thanks in advance

[@lexus_offroad_adventures]

I’m not sure what would be required for the conversion, but I’d look for pics of any sequoia base models that come with coils from factory. I would also look for the rear suspension parts diagram for the base model to see all the part numbers you’ll need. The coil springs and air springs should be inert when it comes to driving modes, so the electronic shocks will handle it as long as the spring conversion doesn’t mess with the electronics (which I doubt it will). Just make sure you research which fuse to pull so you don’t get a constant air suspension error light. Here is an OEM coil spring I found: www.ebay.com/itm/TOYOTA-OEM-08-18-Sequoia-Rear-Suspension-Coil-Spring-482310C020-/274939789211?mkcid=16&mkevt=1&_trksid=p2349624.m46890.l6249&mkrid=711-127632-2357-0 It’s a solid axle, so it should be as easy as you saw in my video

[@keithk888]

@@lexus_offroad_adventures Thank you for the reply, I appreciate it. I have an OEM parts list for the conversion (without shocks) so I think I'm good to go but I'll do a little more checking around first to be safe about the electronics. Regards.

[@damienbell3155]

Awesome video, tip, invest in sum PB blaster lube, It’s a mechanics best friend lol. But hey another great video, your making me want to go purchase a GX470 now lol.

[@jesselawson8762]

Great vid! Sorry if I missed it but did you go with the 2" or 2.8" setting up front? How much lift did you actually get ?

[@lexus_offroad_adventures]

Great question. You didn’t miss anything. However I’m an idiot and didn’t measure before and after like I should have (too excited to get started I guess) This was the lowest setting. Too much rake in my opinion and it didn’t allow enough clearance for 33” tires. You’ll see in a later video that I did that I changed the setting to the 3rd position in preparation for installing a steel bumper/winch. That setting is a bit of reverse rake without weight up front but it leveled out perfectly when I fit the bumper setup. kzbin.info/www/bejne/f6qvhGN8mpqaeLM Let me know if you have any more questions!

[@jesselawson8762]

@@lexus_offroad_adventures Thanks for the the Info and reply! I think since I won't be adding any weight up front, I'm going to go with the 2nd setting. Hope that puts me just about level. Now it's a waiting game for the lift to arrive !

[@Wanyekerr]

Did any VSC or check engine light come on due to the air bag delete

[@lexus_offroad_adventures]

No you have to pull some fuses. I went on metaltech 4x4 site instructions to find out which ones metaltech4x4.com/content/GX470-GX460-4Runner%20Rear%20Coil%20Conversion%20Kit%20v2.pdf

[@Wanyekerr]

@@lexus_offroad_adventures what year gx do you have

[@canonfodder808]

Did you need to drop the sway bar with shims?

[@lexus_offroad_adventures]

I did on the fronts. I used the icon spacer kit so the sway bar didn’t hit the springs. But I no longer run sway bars at all

[@allstat1290]

Did you use the oem top hats back on the front struts? My kit did not come with new ones so I’m assuming you have to take them off the old suspension?

[@lexus_offroad_adventures]

Yes I believe so. This video goes more in-depth on the fronts: kzbin.info/www/bejne/f6qvhGN8mpqaeLM

[@hehexd1769]

Hey, quick question, if you're supposed to retorque the wheel spacer bolts after about 100 miles, hows does that work with the thread locking compound? Wouldn't the nut be sealed and locked in place from the thread lock? Thanks!

[@lexus_offroad_adventures]

I did not do that but I believe what they mean by “re-torquing” is to just check that they haven’t come loose. So the bolt shouldn’t get any tighter when you check that, and therefore you shouldn’t break the seal with the thread lock. If you do check it and the bolt rotates further, you’ll want to re-do that bolt anyway because something is wrong. The only reason for that to happen is if something got caught in there and somehow fell out during that 100 miles or something...

[@Flareside94]

Awesome video. Great work! Does anyone know around how much this would cost at a shop?

[@BergFamilyable]

Did i miss it, do you need to calibrate or do anything to the electronics after air bag delete?

[@lexus_offroad_adventures]

Yes there are a few fuses to pull. I just looked at the Metaltech airbag delete instructions to see which ones. Scroll down and select install guides: metaltech4x4.com/metal-tech-gx470-rear-coil-conversion-kit-stage-1/

[@ericschaumburg6382]

Can you adjust the height on the Eibach pretty easily? Also I noticed this Eibach Pro Kit doesn't have an option for the air to coil conversion...is that needed? And if so, are the upper isolators needed? Not really sure what they do.

[@lexus_offroad_adventures]

The upper idolaters just provide a small barrier between the spring and the upper spring perch. Just nice for a bit of comfort. Not sure if they do much but I haven’t had any issues with them. As for height adjustment, that’ll only be on the fronts and I made a full video on that process. It’s difficult. You have to take the front coil overs out and do it. Best to get it how you want it the first time. I’ll find the link to that video

[@lexus_offroad_adventures]

kzbin.info/www/bejne/f6qvhGN8mpqaeLM

[@ericschaumburg6382]

@@lexus_offroad_adventures Thanks, do you know where to find an air to coil conversion kit with upper isolators that aren't close to $300? Seems like a lot...Also, did you weld your own bumper or buy it pre-built?

[@yota_guy8955]

how does the Eibach suspension ride?

[@lexus_offroad_adventures]

It’s great! Stiffer than stock which is good for off road confidence. Ride Gets better as you add weight.

[@yota_guy8955]

@@lexus_offroad_adventures sounds good man, thanks for replying back. Now I dont know what to go with Eibachs or Dobinsons haha. let you know whichever i go with.

[@ampog1788]

great vid! are you running 33’s after the lift kit? any rubbing issues that needs minor trimming? thanks!

[@lexus_offroad_adventures]

Thanks! Yes I run 33”s. It takes some trimming and pushing the front of the mudguard forward into the front bumper. If you watch the follow up video, I show you how much of a pain it is to change the setting from the 1st to the 2nd or 3rd setting lol kzbin.info/www/bejne/f6qvhGN8mpqaeLM Moral of the story, just go with the 2nd setting if you’re not getting a steel bumper/winch and want to be level. It’ll also make it easier to fit bigger tires as well. The other way to fit bigger tires that nobody talks about: have your alignment guy put caster as far positive as possible to clear the body mount behind the tire.. This will necessitate more cutting near the front bumper but that’s less invasive than a body mount chop. Positive caster essentially pushes the front wheels forward in the wheel well.

[@ampog1788]

@@lexus_offroad_adventures awesome ill keep that in mind! where did u get your lift kit? do u have a code i can put in to credit u for promoting the product. and also what exact size rims and tires u run it with? thanks a lot and keep making more videos like this!

[@henryman4643]

Great How to! I am about to buy the same kit, but besides the UCAs did you buy anything else? Like a Diff Drop? What was the total lift after the install?

[@lexus_offroad_adventures]

No diff drop. The GX is blessed with pretty good CV angles. If you go for the second clip on the front shocks, you’ll be level. I made the mistake of leaving it on the first clip so there’s a bit of rake. Rear should be 2.5 inches or so and fronts around 2-3” depending on the clip. Use the second one to get to 2.5 as mentioned before. Best of luck! Let me know if you have any questions when u do the install

[@henryman4643]

@@lexus_offroad_adventures awesome advice! Thanks! I’ll def let you know!

[@Psilocy-ben]

Great video thanks for sharing. Any tips for removing the front struts?

[@lexus_offroad_adventures]

benoblest I removed them without unbolting the Lower Control Arm or the Tie Rod ends. It’s a squeeze, but if you are patient, once you remove the strut assembly hardware, you can work it down thru the bottom of everything while it’s still bolted up. Saves a bunch of time and leaves the factory hardware in place

[@Psilocy-ben]

Daniel G thanks for the reply. I may try that way. One more question, how hard was the VSC hard to remove? I heard the bolts are hard to access.

[@lexus_offroad_adventures]

benoblest That hard line is just held in by a bracket and a 12mm bolt. Just be gentle and massage it out of the way. It’s probably one of the easiest bits of the job. On my How to Replace Wheel Studs video you can see how it looks since I had to remove the brake caliper. I think the hardest part about the job was that I didn’t have a good spring compressor for removing the top hat and oem springs. I had some sketchy $18 Amazon compressors. It was a lot of effort and it was scary. I would gladly pay a shop $50 to do that bit for me. Keep the questions coming if you have any! I wish I knew what I did now before I attempted the job so I know how you feel and will gladly provide info

[@Psilocy-ben]

Daniel G okay cool, yeah I’m slightly afraid of doing compressing the coils using the spring compressor I have. I’ve seen videos of people change them without one using the weight of the truck and jack stands but that way also seems kinda of sketchy too. Maybe I’ll try find a local shop that can swap them out real quick. Last question, I’ve heard the top bracket that holds the factory adjustable electronics in the front is hardest part to remove. Any tips for getting that bracket off? Thanks again!

[@lexus_offroad_adventures]

benoblest no problem! yeah using the weight of the truck and jack stands seems all bad lol. Those electronics weren’t too bad. I remember that one side was easier than the other. If I remember correctly, I think I had to pry and break the top off one. Once I broke it off, then I could reach the bolts on the back side. Then you just unclip the harness plug and it’s free to take out and reach the nuts at the top of the shock tower

[@amitvachher]

I see you have installed these as well as the Luft Meisters, can you give us a breakdown in which you prefer and why? It appears you did the Luft Meister install after this one, so I’m curious as to what the short comings of this setup was and why you chose to back to a stick like setup?

[@lexus_offroad_adventures]

The Luftmeister was for my stock GX (I have two) and this setup is for my modified one. The difference is this Eibach one is a lift kit and the Luftmeister is a stock replacement

[@amitvachher]

@@lexus_offroad_adventures In terms of ride quality how do they compare? Are you happy with this kit? I have been putting serious contemplation to removing the air bags and installing a kit like this, but I also find that the stock height serves me just fine for the majority of overlanding and camping trips. Did you feel like this kit gave you a significant off road advantage over the Luft Meister setup?

[@lexus_offroad_adventures]

@@amitvachher kzbin.info/www/bejne/rJKkaWCFl6psapI Here are my recommendations for modifying your GX for off-road use. This Eibach kit (as well as any other off-road focused ones) will be stiffer, tougher and much more resistant to bottoming out off-road than the stock suspension. They will also be engineered to support the weight off heavy accessories most people add to their rigs. As I explain in the video I linked to, I think larger diameter off-road focused tires are the most essential off-roading modification, and a lifted suspension setup will both allow you to fit bigger tires and give you a more secure ride when off road. The squishy stock suspension and tires are not good for any serious trails but should be fine on the odd dirt road. If you want to retain the stock ride-quality, I think just keeping the stock suspension as long as it lasts is a good option, then decide whether to get a lift or just replace stock components with replacement stock parts. It’s important to note that, this Eibach kit was a full kit (springs & shocks,) and the Luftmeister ones I installed in the later video are not a kit. They are just rear stock replacement shocks that are cheaper than OEM Toyota.

[@lexus_offroad_adventures]

@@amitvachher I personally think the Eibach kit is fantastic for my purposes, but you need to listen to your own priorities. I have a lot of weight on my rig and go on some tough trails. If you plan on doing the same, it’s a great kit.

[@z115663]

How are you liking the lift kit so far? Near stock ride comfort?

[@lexus_offroad_adventures]

I would say that it’s a more firm and reassuring ride. Especially since my stock suspension was not the best and I would bottom out on the bump stops regularly in the rear. With this kit, the truck feels much more solid, which is more comfortable for me vs. an iffy, soft setup.

[@peteru9980]

Nice install, can you drop a link for the spring and shocks kit

[@lexus_offroad_adventures]

Sure, here are the UCA’s: apacheoffroad.com/product/freedom-offroad-upper-control-arms-2-4-lift-toyota-fj-cruiser-4-5th-gen-4runner-gx470-gx460/ Here is the Eibach pro truck lift : apacheoffroad.com/product/eibach-pro-truck-2-3-lift-kit-03-09-lexus-gx470-free-shipping/ Looks like both are out of stock right now but it also took a while for me to to receive mine so just place your order and sit tight they should be able to get you your parts pretty soon.

[@peteru9980]

@@lexus_offroad_adventures thank you 🙏

[@wyattwhitener5358]

Daniel, How are your liking your Freedom Offroad UCA's? Looking at getting some within the next few days.

[@lexus_offroad_adventures]

Wyatt Whitener I really don’t know why people spend $800+ on other non adjustable UCA’s. They seem very robust, the ball joint looks solid, and my alignment guy was able to get my lifted suspension in spec no problem. There’s a lot of Gucci gear out there but these just work. Plus, they look great as well. No downsides from my perspective.

[@wyattwhitener5358]

@@lexus_offroad_adventures I appreciate your reply. Ill probably order some soon. Where did you order yours from?

[@lexus_offroad_adventures]

Wyatt Whitener apacheoffroad.com great customer service. Some delays due to high demand but they were always responsive. I also ordered the lift thru them. Took a few months

[@lexus_offroad_adventures]

Wyatt Whitener I guess I should share the actual product page apacheoffroad.com/product/freedom-offroad-upper-control-arms-2-4-lift-toyota-fj-cruiser-4-5th-gen-4runner-gx470-gx460/

[@ericschaumburg6382]

hey did you do an airbag delete kit?

[@lexus_offroad_adventures]

Hi! Yes this kit deletes the airbag by replacing it with springs and isolators. You don’t really need to do anything else other than pull some fuses.

[@peteru9980]

Do we have to replace the UCA or we can use the old one

[@lexus_offroad_adventures]

As long as you don’t lift it too high, I think the stock UCA is fine. It just makes it more difficult to get the correct alignment. If you go beyond a certain lift (probably closer to 3+-” I believe) it will be impossible to get your alignment in spec. I just did aftermarket UCAs for more durability and to make it so I don’t have to worry about alignment issues in the future.

[@peteru9980]

@@lexus_offroad_adventures thank you, just ordered

[@rodneyburt8843]

How much was the lift kit? I am looking for GX currently hope to find one in good condition.

[@lexus_offroad_adventures]

Rodney Burt Eibach sells these for $810 last I checked. If you’re trying to get a good deal, find one with blown rear air springs (since you are installing a lift) and a leaking transfer case actuator. I made a video on how to fix that common issue.

[@rodneyburt8843]

@@lexus_offroad_adventures Thanks I will check those videos out. I am in rust belt so I am having hard time finding one in good condition.

[@lexus_offroad_adventures]

Rodney Burt oh yeah, I could see how that’s a problem. Well best of luck to you in your search! I am continually surprised by the practicality and capability of this vehicle. You’ll love it

[@jimmydoan007]

Can you give us an update of your conversion? Would you still recommend it? TIA!

[@lexus_offroad_adventures]

So worth doing. Most of these trucks’ stock suspension is blown anyway. You can tell this kit is setup for having some weight on it (steel bumpers, roof tent setups, etc.) but I plan on putting that stuff on anyway. There are literally no downsides that I can think of. I only regret not putting the spring perches on the second setting to raise the front a bit more. I’ve high-speed off road tested it, rock/rut tested: the setup with the Eibach pro truck kit/Freedom Offroad UCAs with the 255/80/17 Falken Wildpeak AT3Ws is really good. I just recently added the White Knuckle off road sliders (check out the video) and having that extra weight helps smooth out the ride even more. Totally recommend. Price is second to none for what you get.

[@jimmydoan007]

@@lexus_offroad_adventures Thank you... Where can I buy it?

[@lexus_offroad_adventures]

@@jimmydoan007 I bought from Apache Off-Road

[@jimmydoan007]

@@lexus_offroad_adventures thank you!

[@house22TC23]

Is this your first time working on suspension ?

[@lexus_offroad_adventures]

It was, yes.

[@house22TC23]

@@lexus_offroad_adventures you make it look easy. Any tips and advise for first time ?

[@lexus_offroad_adventures]

@@house22TC23 yeah, definitely, it make sure to watch this video just to see how the fronts get installed. It’s a GX460 (newer) but it’s the same principle. kzbin.info/www/bejne/opSkZq1qjrWIis0 For the rear airbag delete, I think my video explains it fairly well. If you have any questions, you can comment and I’ll try to answer

[@house22TC23]

@@lexus_offroad_adventures okay. Do you have an email just in case I need to send a pic?

[@lexus_offroad_adventures]

@@house22TC23 honestly, I check KZbin comments more regularly, but you can dm me on insta @d_geleris

[@mattstager184]

You forgot to bolt the top spring isolator in

[@lexus_offroad_adventures]

The kit didn’t come with hardware to bolt it in. But I’ve not had a single issue with it held in there by the weight of the vehicle. I even upgraded to HD springs in a later video and had a chance to check everything over. It’s all good up there.

[@SebastianMartinez-cj8nb]

2in rear coils?

[@lexus_offroad_adventures]

Sebastian Martinez I forgot to measure the difference. It wouldn’t be accurate anyway as my air springs were blown. 2” seems about right though, maybe even 2.5” with no cargo