Lian Li SUP01

[@isuguy82]

Kleo, this is the best case review I have ever seen. If only the big time KZbinrs were this thorough. Thank you!

[@KleoYan]

Hi Thomas Lage, welcome to my channel and thank you for your kind word. All the best with your build too 😉

[@jeudaz]

Hi Kleo, good to see you are still in action since DMD dayz.. subscribed your channel to show support!

[@KleoYan]

Yo Jedaz, how are you. it's been sometime now.. hope you are doing great too at your end. yup it's been a long while since De Merlion Dan. Glad to see you too. 😉

[@ayankga]

Most detailed case reviewer i've ever seen!!

[@KleoYan]

Hi muchos unos, welcome to my channel and thank you for the feedback. All the best with your build too 😉

[@t.7527]

Love this breakdown and love yhis case !!!

[@KleoYan]

HI T., welcome to my channel and thank you for your feedback. Alll the best with your build too. 😉

[@408civettethreat]

I truly feel that you are the next up and coming tech tuber they everyone is going to go and view first. Your attention to detail and explanation is above the rest! Keeep up the great content. Thank you for everything you share with us. ❤ 🍻

[@KleoYan]

Hi QuantumOutbreak ๏, welcome back. Thank you for all your kind words and your support. I will keep up as your motivation means a lot to me. Thank you so much 👍👍👍

[@408civettethreat]

My SUP01 just arrived yesterday and it was your video that got me interested in the case to begin with. I went with the white version since dark color shows every spec of dust 😂

[@auroraflash]

wow, another one bites the dust - and mounts the fans inside the chamber. Ever thought about mounting the radiator fans to through the bracket to the radiator, so they can actually pull in fresh air?

[@KleoYan]

Hi auroraflash, welcome to my channel. I do agree with you on this point whereby it should be even better for cooling the Radiator. Do pardon me as this content is just an illustration of some placement and alignment on PC Components in this case. Thank you again for your feedback and suggestion. Greatly appreciated it 👍👍👍😉

[@auroraflash]

@@KleoYan Lian Li apparently did it wrong in the presentation and so did everybody else following up. But the case has a very special airflow concept and I would think it makes a huge difference because of that.

[@KleoYan]

@@auroraflash hmmm, you mean the 4070ti GPU at the front. I have mentioned this to them and they did provide a solution. Flip the holding bracket but will need to remove off the rubber gourment. I will be doing up another content on this but will take sometime as my work schedule is pretty pack.. Thank you again for your feedback 👍

[@chriswoodrow9156]

Great video. I just preordered the white version. This is the first case ive ever been excited about.

[@KleoYan]

Hi Chris Woodrow, welcome to my channel. Nice and congrats. Thank you for your feed back and do let us know your experience when you have completed your build. All the best on your build too 😉

[@BravoSixGoingDark]

Hey Kleo Yan, its me again, another fellow Singaporean, want to ask if you're keen on reviewing the ''Jonsbo Jonsplus Z20 MicroATX Desktop Case''. The one with a handle bar on top of it for portable transportation. I found your Lian Li Dan A3 mATX Chassis video (watch half way around 20min+) to be very thorough. You went through the various types of PSU placement. Very Insightful.

[@KleoYan]

Hi Bravo Six Going Dark, welcome to my channel. Let me see if I can request from our local distro. If they allow me to, I will be glad to do the Jonsbo z20 chassis. No promises though.

[@kitisme]

Lian Li never stop making me surprised with their innovative concepts xD Can't wait to see how well is this case's performance

[@KleoYan]

Hi Kit, welcome to my channel and thank you for your feedback. 😉

[@408civettethreat]

I know I am posting on a 3 month old video. But I have a question about my fan configuration. Do you recommend the radiator to be a pull configuration ?As well the 3 fans between the video card and radiator to be a push configuration Kleo?

[@KleoYan]

Hi QuantumOutbreak ๏, welcome back. I did a test with this case on airflow but havent got time to do a content. My finding is this, if you have strong static pressure fans. you can do pull configuration on the radiator, as it gives the same result be it pull or push, but if you use a less static pressure fan, then it will be best to do push configuration on the radiator. In general, if you are using Phantek T30 fans, you can do pull configuration. But if you are using Lian Li own uni fans be it AL SL or SL-Inf, it will be best to do push.. As for the lian li P28 or TL, you can do pull configuration. Hope this help.

[@miiasutherland852]

Your reviews are always very thoughtful. Thank you. This is a very cool case.

[@KleoYan]

Hi Miia Sutherland, welcome back and thank you for your kind words 👍👍👍 greatly appreciated it 😉

[@Seddoo]

Hi Kleo, Why are new content not coming anymore, is there a problem?

[@KleoYan]

Hi Seddoo, welcome back. nope there are no problem, just that am busy with my main work schedule. I will be back soon. , so sorry about this and thank you for asking.

[@haies09]

That cutout for the HDMI/DP cable really ain’t that big. I run two monitors and I bet the cables won’t fit, especially for those that run 3 or 4 monitors.

[@KleoYan]

Hi Haies 09, welcome to my channel. If you pass through two connector at the same time. That cut out is small. But if you pull through one connector at a time. That should not be a problem.

[@haies09]

Btw you just saved me from wasting money, as I have a Liquid Freezer II 😊

[@KleoYan]

Hi Haies 09, welcome back. That’s good. No point to get a case where your component cannot fit. 😉

[@xOgichi]

@KleoYan Assuming I want to run dual GPU for LLM, is the riser cable long enough to allow a 2nd gpu to sit in the 2nd PCIE slot and still route to the back? Looking at something like a ASUS TUF 3060TI (301mm length)

[@KleoYan]

Hi Ogichi, welcome to my channel, I do not adivse you to have dual GPU. the only slot is at the front and even if you are to fit the 2nd GPU. the height of the 3060TI tuf is at 143mm where the case as mentioned has only clearance for 88mm (Max). Another point is. the PCI-E slots are of low profile. the Tuf GPU is a full PCI-E slot profile.

[@hlchwa3190]

Hi Kleo, do you know if we can use Corsair rmx shift PSU in this case?

[@KleoYan]

Hi HL Chwa, welcome to my channel. In general, this case have a solid frame across the two section between the upper part and the PSU with HDD compartment. I strongly do not encourage to use the Corsiar shift PSU as there are no space to move your cable from the side to the top section.

[@edwinwelch1946]

can you tell me when the freezer 2 is places how many MM are left between the fans and the back of the motherboard tray for airflow. Im interested in this case and have the freezer 3 but trying to see how much fan space there is for airflow

[@KleoYan]

Hi Edwin welch, welcome to my channel. it will leave you approximately 12 to 13mm of space.

[@edwinwelch1946]

@@KleoYan awesome thanks. Lian Li messaged me just recently also that there is 76mm of space so the freezer 3 is 63 which leaves 13mm of fan space. Does not seem like enough space between the tray and fans to breathe properly IMO

[@KleoYan]

@@edwinwelch1946 a 13mm space is more than enough to pull air from the fans unless you are taking about 5mm space or to place the fans first at the side panel and follow by the rad which is near the motherboard. Then that will be some obstruction.

[@ahuman8711]

damn it is already here in this country

[@KleoYan]

hello A Human, welcome to my channel, hmm not sure whcih country are you refering to?

[@ahuman8711]

Where are you from?

[@KleoYan]

@@ahuman8711 I am from Singapore and you?

[@ahuman8711]

@@KleoYan same, that's why I was surprised this case is already here, thought this case was pretty cool when i saw youtubers at computex

[@AquilaeYT]

Lian Li never stop to disappoint me in terms of design/aesthetic. Imho their case look awful, i wonder why they persist by making cheap looking/mesh case which i really didn't like at all, it take so much fingerprint etc Case like NZXT/Fractal with their terra for example or some Corsair are so much better in terms of looking, no mesh panel but strong large metal front panel with original design, i just cannot buy anything from Lian Li.

[@KleoYan]

Hello Aquilαe, welcome to my channel. Thank you for your feedback. I believe each have it's own taste on case design. It will still be good if you can pass this feedback at Lian Li's reddit forum as they do read and take in feedback. Don't get me wrong, your feedback here is greatly appreciated too but the impact of what you've mentioned, there might be other PC builders who feels the same way. Reddit has a bigger crowd and that alone can influence others to feedback too. 👍👍👍

[@AquilaeYT]

@@KleoYan Hi (i'm not new here haha). Sorry but i don't use reddit, it's not relevant at all and have a illogical/bad system which is called (karma system). Also, i don't think a brand would care about a negative opinion about design while this is their identity to provide cheap looking design case compared to others competitor. This is just not in my taste and I found their case absolutely not aesthetic at all, i prefer a case that suit me/my personality and my space than taking a case that search just "performance" over all other criteria.

[@KleoYan]

@@AquilaeYT Oh! sorry about that.. welcome back 😁 nevertheless, thank you for the feedback 👍👍👍

[@maxsunz3703]

Lian Li not Liam Li bro please edit bro 😂

[@KleoYan]

Hi maxsun z370, welcome back and thank you for correcting my typo. 👍👍👍😁

[@lucasjuniorproducer]

To tall. I love Liani Li but this case its just NO! Remind me a frigobar on a hotel...Just ugly. And half size expansions slots???? The designer i guess he was drinking a lot of beer when drawing this Frankestein case. Where are you gonna put all cables behind with those 3 fans and a radiator covering all the back? This is just so stupid. And what about Air Coolers lenght? Im just dissapointed... Lian Li? Please... Im saying this and i have a Lancool 2 mesh and a 216, But this case never!

[@KleoYan]

Hi Lucas Junior Studios, welcome to my channel. Thank you for your feedback. I guess it does have its own audience. It greatly depends what you are looking for. 😉

[@lucasjuniorproducer]

@@KleoYan I understand, but as i am a Lian Li fan and love they products this was just a disapointment to build. But i guess this case will have own audience as you say, but it wil be a Flop. Can you imagine people that need ful size brackets, or thats just have a 2060 or a 1070 or a 5700xt and cant mount the graphics card? The cable management also will be terrible, not to mention that Air Cooler space is not present and also on Liquid coolers the cables will be allways in front of the pump. You must agree that this is the big Lian Li Flop since ever. 10% of people have 4080 and 4090, what about the 4060? Im very sad with this product launch from a company that i love so much.

[@KleoYan]

@@lucasjuniorproducer this I do agree with you if just wanting to build a decent system into this case. Yes it’s a disappointment but my opinion about this case is meant for people who wanted all highend products and to flex their components in a unique way, so I wouldn’t say is a disappointment in general. We have to look at the situation in an overall stand point. Example, I hesitated to publish this content, supposed to be on time as I worried about losing sponsorship, but my conscious is right. By explaining the limitation which aid others from purchasing impulsively, this is what my channel is all about. As for the sponsorship, I strongly believe Lian Li will take this as a good feedback and to improve their products which are proven so many times. So ya. In addition with my explanation, I believe this will prevent pc builders from questioning Lian Li as why these are not mentioned in their product page? By the way thank you for voicing your opinion. 😉

[@lucasjuniorproducer]

@@KleoYan If i wouldnt like Lian Li i would not comment... So thanks to you and your channel. You do a great work. And yes i still love Lian Li. But im not a customer of this case. :(

[@KleoYan]

@@lucasjuniorproducer hahaha.. you are so cute.. no worries. not everything can please everyone, so ya not worries 😉

[@sgttosun]

What is your insta?

[@KleoYan]

Hello sgttosun, welcome to my channel. I do not use insta, do pardon me. If you need certain help, you can reach out to me at [e-mail]. I will try to help you out as I can. Thank you!