Lian Li UNI FAN TL LCD - Installation Guide

[@MrBobbi93]

Thank you for making this. I plan on buying the non-lcd fans and I needed a step by step video because the last fans I bought were overly complicated to sync.

[@thesagaofblitz]

Make sure all your fans are lian li TL. They have SL and AL too and I believe the boxes are exactly the same. If all your fans are TL they will all work on the same controller just make sure that the LCD fans are not plugged into Port 1 because apparently there's an issue with that. Provoked prawn also has several phenomenal breakdown videos on these fans and their installation guides

[@napoficial7123]

One of the best KZbin PC channels❤

[@darrendavies1102]

Omg just amazing, it's like Iben transported to the future . Great blog. Love them and your channel

[@ChristopherFlannigan]

Thanks

[@acroonstix6380]

@@ChristopherFlannigandoes the PCIe cables for the controller come with the power supply because I can’t find it with mine

[@Tommy-h2x]

So does the controller use a PCIE port from our motherboard or is it a SATA cable? My power supply doesnt have any available PCIE slots since I have two of them for my Z890 MOBO and 3 PCIE slots going to my monster RTX 3090ti that takes all three.. so all 5 of my PCIE ports on my motherboard are being used already

[@mtlgtr-q6k]

Thanks for doing this. Have you considered doing a full build with this all together in one video? All Uni LCD for push pull Aoi, bottom intake and rear exhaust? The struggle is real😂

[@SunDance00]

if you only have 1 140mm lcd fan you need to connect. do you still need a uni hub for it or could connect it directly to the MB somewhere?

[@adampratts4649]

New build, hydro shift TL AIO , 3 TL LCD, and 3 TL bottom with a rear 140mm tl. L-connect doesn’t pick up controller. They all spin and light up. Just can’t control rpm and rgb my self

[@StyleNasty]

Is there a way how to connect a single TL LCD fan to the motherboard without the controller? Thank you for the answers 😊

[@GanymedeXD]

No, there is not. You must use the controller. How is this supposed to work. Those are fans with LCD displays. You must have software to control the LCD display … this is done via l-connect and the controller. Without controller you would have a useless LCD fan.

[@EclipsisCorvus]

What's your thoughts on these and the other Lian Li fans vs the Phanteks D30s? I love the look of both, but to my knowledge Phanteks doesn't have software controls for lighting etc? I currently plan on either a NV5 or O11 Dynamic case if that is a factor really

[@luxubu666]

Thank you sir 🙏🤩. Very useful even though I can't afford to buy it 😂

[@basedpinkcanary3624]

Do I need a new hub for this I have a AL120 v2 hub currently.. i just want 1 for the rear vent

[@GanymedeXD]

You must have a tl hub for tl fans!

[@elchancho8432]

Okay so on PCpartpicker it says I need an additional USB 3.2 Gen 2 header because these fans take it and my case also needs it Do I just buy a USB 3.2 G1 to USB 2 header adapter and I’ll be good?

[@TPA_JW]

To confirm, if I am only interested in controlling the fans and light via LConnect, do I need to plug in the PWM and the RGB connector to the motherboard? Also regarding the 6 pin PCI-e power, does that just use a standard pci-e cord from the power supply? My cords are 6 plug that go into the P/S and the opposite end is a 6-pin with an additional 2-pin. Assume I just do not use the 2-pin on the end?

[@noth606]

Regarding the power cable, pci-e is often 6+2 like you have, you'd only plug the 6pin block. The stuff on the power supply end is proprietary dung often enough that you should never, ever consider plugging anything other than the exact cable that came in the exact box with that one specific PSU. Even if you have another PC with the same brand and even model of PSU, swapping cables from one to the other may result in broken components and in the extreme: fire. You can probably guess how I know this. Wonderful world where everyone and their uncle uses the same physical connector, but the pins used are picked at random, not even by brand/make or even model number, but by 'revision'. Do _not_ mix power supply cables.

[@GanymedeXD]

@@noth606What are you going in about … you did not answer the question, instead wrote a lot about something that was not asked. His PSU included PCI-e cables are split he can plug either 6 or 8 on the PSU side. He simply wanted to know whether to plug in all 8 or only the 6. He did not intend to exchange anything. Just a connection question.

[@GanymedeXD]

You use a PCI-e cable so on the PSU side it goes into the 8-pin PCI-e ports … using all 8, not parts of the cable. On the PSU side none if mine are split … it goes 6-pin to 8-pin. If it would not matter it would be easy to avoid the blocked 8-pin ports issue many have.

[@jeanbiroute]

Can you ask it to cycle trough the sensors?

[@RyanArtis]

Hi Chris I’ve followed theses instructions and there’s no power or lights on my pc

[@GanymedeXD]

It might be useful to give a minimum of information … you even fail to describe the problem … no power and lights on your PC … then you seem to have a power problem with the PC, not fans. If its just the fans that do not work then the fans have no RGB and are not spinning … your PC should have power and lights on. Just the fans being dead. Do basic troubleshooting. Check connections. Take everything out and re-fit. Stick to limitations 16 max, 9 max LCD. Max 10 per port, mac 3 LCD, no LCD port 1. Sata power if 6+ on one port. To give advice you must share detailed setup, which fans, other fans, aio?, controller setup, info on l-connect … no power & light PC is not enough …

[@Paul-if1jq]

Ihave everything the same as you excepot i have the hydra AIo, the only issue I have is in Pump/Fan profile - it says no fan products detected. It all works, but nothing shows on the screen

[@nathandraycott]

Did the fan controller you used come included with either the AIO or the fan triple pack? I have seen that there are different Lian li controllers

[@paultodd2838]

There are SL and TL controllers - I ended up with both. The controller comes in the triple pack not sure about the AIO

[@Divyam4070]

How do u chnage the direction of air flow but keeping in lcd your side

[@YoTrauma]

More elaborate explanation by JayzTwoCents: kzbin.info/www/bejne/fJi6Y6lqprKcfJo

[@Divyam4070]

@@YoTraumai get it. Its reverse blade fans

[@GanymedeXD]

‘Your side’ … makes no sense … some people have transparent mesh … and they would be visible. All intake fans you want to see from inside the case need reverse blades. You could use on exhaust as well …

[@Psychohand]

I will have any problem if I only buy one of these fans? I see that it looks great in the back of the case (taking out the hot air) my doubt is because I have 6 infinty fans of the same brand... and according to the software, I see that I need the 2.0 ver for this new version, according to the web, is NOT compatible with the rest of my fans (Lian Li Uni Fan Infiinty), then, I will have to use 2 Lian Li software (L-connect 3) with different version (1.4 and 2.0) at the same time if I want to integrate this new fan to my setup????? Thanks in advance and nice video!

[@GanymedeXD]

I do not know what you are referring to … of course you need the latest l-connect 3 to work with the latest fans … but where do you get the info you need an old version for SL fans … think you muddle up the controller situation with the software. You cannot even have 2 versions of l-connect 3 … if you download the newest version … the old one is exchanged. Going back to a previous one the new one is gone. TL fans are not compatible with other fans and you must buy a controller to use one of the TL fans.

[@Nixdawg1]

If I wanted to set them up as an intake would I have to purchase the reverse version of the fans?

[@trackmedixuk]

Yes

[@thepopeofkeke]

Yes, but your fan set up will suck.. That’s just a joke, your cpu temps will always be better with the fan intaking ambient air.

[@GanymedeXD]

⁠@@thepopeofkekeWhat are you going on about? He simply wants to see the front so needs reverse fans as intake … they suck air in from the outside … so not clear what you referring to?

[@GanymedeXD]

Depends on what you want. You NOT require reverse as intake. If you want to see the front of your intake fans from inside the PC, then yes, reverse fans are required.

[@thepopeofkeke]

@@GanymedeXD not gonna re watch the video but my assumption is these were LCD fans that would need reverse blade to still use the screens. If not then I just misspoke as reverse blades would not be needed you just turn them around.

[@МаксимСеров-ю4н]

Hello! Are they compatible with LIAN LI UNI FAN SL Infinity? Thank you in advance for your answer.

[@jasperchou4952]

they're not

[@GanymedeXD]

Of course not … TL are only compatible with TL fans …. Means you must have second controller.

[@MikeBCNU]

and yet failed to show a SINGLE wire header on the motherboard or power supply

[@GanymedeXD]

He did show everything that you need to do … what else do you need?

[@WarAnWaar]

Hi! What now when i bought UNI FAN TL LCD 140 Reverse Black 3X single pack ? What i need to work? i get cable onnly one ,,,,can i connect without controlller?

[@GanymedeXD]

Why did you buy 3x Single Fan. You need the TL controller for them to run.Even if you only want 1 fan, you must use TL controller. Thats included in the triple pack. Buying single you paid more than for a triple pack and now must buy the controller on top. Return them a buy a triple pack. Single here they are 45-50£ … the triple I paid 130£ for and controller was included.

[@O-Friendly]

Do they make the tl lcd fan as an exhaust without having to flip the fan on the backside where the screen will be covered?

[@GanymedeXD]

Weird question … a normal fan out of the box with visible front from inside the PC is always an exhaust! Its the intake fans whose front is not visible as the rear is visible from the inside. If you want to see the front of an intake fan from the inside you need reverse fans. Those are available for the TL series. A fan sucks in air … hence out of the box only exhaust fans are visible on insude.

[@VickyLatorreArt]

What temperature should the CPU and GPU be. My fans are showing 30 to 45 C for the CPU and 33 C for the GPU. I convert the Celsius to Fahrenheit and it says around 80. Is my CPU cooking, is it going to burn up?

[@GanymedeXD]

You make absolutely zero sense … you got CPU temps on the low normal side and write stuff about cooking it whilst you are freezing it? If it goes above 176 F you can acquire damage to the CPU. 104-149 F is perfect. You got 80 F … you need to make sure its not frozen … no idea why you think it might be cooking.

[@jorgemejia7179]

I installed 3 lcd fans to one port and 1 lcd fan to another port and 3 led to fans to another and they not displaying rbg ?

[@GanymedeXD]

What about providing a minimum of information? What kind of ‘LED’ fans? For TL you must have the TL hub … for SL/AL the corresponding hub!

[@ab8701]

I have a situation. Do you connect the GAII trinity cable into the fan hub? if so the head are smaller and divided into two pins. can you help?

[@GanymedeXD]

You only connect the fans to the controller. What ‘Trinity’ cable? Where does it usually go? Thats most important. The TL controller are only compatible with TL fans.

[@JamesTodd]

I have 9 sl inf fans and i bought 1 reverse lcd fan for the rear. Can the LCD fan work off the same hub?

[@phabran]

Nope. It's a different controller.

[@GanymedeXD]

Common sense … the LCD fan has a LCD fan to control! TL fans require their controller thats only TL fans!

[@theplaidgamer1653]

I just ordered a single 120 LCD fan and the hub. My PSU has 4x (6+2) pin connectors and 3 of them are used by my by GPU. Can i use a Sata to 6 Pin adapter instead of connecting to the 4th (6+2) pin connector?

[@paultodd2838]

I looked at this but believe the controller needs to go on the PCI-E?

[@asutora.5363]

a double sata to 6 pin would be preferred

[@trevormcgrath9817]

Thanks mate. I bought a whole stash of TL’s and TL with an LCD and fuck if I could work out the plugs now. I understand the different plugs. I’ve got a feeling of supply incorrect plug with the LCD fan.

[@GanymedeXD]

There is nothing to work out. Basically it is straight forward … there is just one power cable in the box … the fan connector you attach to any side. Thats it … the fan goes to controller. Controller to usb, PCI-e, RGB, fan controller. It could not be any easier … if you got the correct cable … more than easy … it says KCD for LCD fans. Why do you think you got a wrong one?

[@Mike-hs8fq]

@@GanymedeXD where do you see KCD my wires doesn't say? I'm having the same problem with lcd not working and the L connect 3 doesn't recognize the tl hub. It sucks.

[@xantech42]

Quick question...I have installed 3x Lian Li Uni Fan TL LCD 120mm reverse blade fans and 3x Lian Li Uni Fan TL 120mm Reverse Blade Fans....when I power down the computer everything switches off as normal...all the RGB turns off too...but all 6 fans remain spinning...I have triple checked all the connections between the fans and controller and motherboard...I have also checked the BIOS and I'm stumped...no matter what I try they just never stop spinning....they'll only momentarily stop during a system reboot....any suggestions would be greatly appreciated

[@GanymedeXD]

Check l-connect 3 … does it interfere with motherboard software? Did you plug in the pwm plugs?

[@xantech42]

@@GanymedeXD there’s no interference…everything is plugged in correctly….triple checked

[@huskesh]

Flamingo bro what's up , waiting for them to launch 140mm version

[@ChristopherFlannigan]

They are up for preorder same as the 120, so hopefully not long to wait

[@deesteez4329]

The non lcd 140mm?? I need those for bottom fans

[@royramos5509]

If I don't have ARGB on my motherboard, I can't connect these lian li LCDs? GREETINGS plz help

[@GanymedeXD]

You do not need ARGB on the mb … its only for those wanting mb RGB control. If you are happy to stick to l-connect 3 this is done via the controller. What mb does not have ARGB? Before adding LCD fans consider upgrading the mainboard.

[@jonathanmiller3613]

That rear fan, was it set to intake or exhaust and can you change it? Do these fans come as exhaust only?

[@SweetLou0523]

You can order reverse flow variants, though they may not be available for a few weeks as they are new to market.

[@jonathanmiller3613]

thanks for the heads up. I'm terrible at visualizing something like this but the regular fans that he installed in the back of the case (The single fan) which way is that going to blow? Into the case or out? Thanks@@SweetLou0523

[@awesomeruben]

​@@jonathanmiller3613you solve this? I'm trying to put a fan in the back and wonder if I should get reverse for it or are those just for the top of the case

[@jonathanmiller3613]

yea to exhauset out the back you need the reverse blades based on what my buddy told me... new egg is all sold out so ill have to wait til the 11th and see if my microcenter gets them in stock. @@awesomeruben

[@awesomeruben]

@@jonathanmiller3613 man that sucks, I picked up the regular fans at the moment, then I'll pick up a reverse fan, The problem is this is the first fan where you need to be 100% on which way it blows because there's an LCD screen now lol so everywhere I went for an answer people just said reverse the fan 😂

[@JaeRowe]

There's no reason these shouldn't work on a Galahad 2 AIO right? Planning on swapping out the included fans with 3 of these..

[@acroonstix6380]

Did it work that’s what I’m thinking it should hypothetically work also if u did it did your power supply come with a pcei to pcie for the controller?

[@GanymedeXD]

@@acroonstix6380Power cables usually come with PCI-e cables … mune had 4 each included.

[@GanymedeXD]

Be careful … the TL fans have flat 7 pin connectors that must go to the controller. The AL/SL had normal fan plugs and were exchangeable with many aio. With the new plugs they do not fit with most aio any more. But that should not be a problem. Simply take a look at the fan’s manual, check with your aio. And then figure out the best connection.

[@ZoField]

maybe someone will have some suggestions... I have 3 of the TL LCD 120's, they are all plugged in, the USB is plugged directly into the motherboard... the fans are spinning, the screens are displaying the default graphics but my LED's are not lighting and L-Connect 3 v2.07 is not detecting the fans/controller, the fans are plugged into port 2 of the controller... I have tried both heads on my MB... I have tried un-installing and re-installing L-connect, I have tried L-connect 3 V2.06... I have checked all my connections... when I launch L-connect nothing is listed under Settings--> Devices... Im at a lost..

[@jorgemejia7179]

Maybe try switching the wiring around on the controller seen somebody with this problem .

[@anthonyp1114]

Did you ever get a fix to this? I’m currently having the exact same issue 😭

[@ZoField]

@@anthonyp1114 It was the controller, however I am having another issue with these fans... if my PC wakes up from sleep mode, they may or may not start spinning again, then I have to restart my whole system in order for them to spin... My PC boots a little hot because the fans come on and go off many times during the boot cycle... These fans are ahead of their time, they need to get working on getting these issues fixed... I had to do a push/pull on my rad because i dont trust the reliability of these fans... luckily i still had the corsair fans that came with my AIO... Im a little dissapointed, and I have 7 of these in my system...

[@GanymedeXD]

I got a weird problem … new build … daisy chain of 9 TL port 1 … 1 TL LCD port 2 … 3 TL LCD port 3 … 3 TL port 4 … linked up to PCI-e, ARGB (tried without), PWM (tried without), usb (tried different). When started system all 16 LL fans not spinning, no RGB. LCD displays working. 4x Noctua for HDD cooling linked via PWM working perfectly fine. I split to 2 TL controllers, tried 6 controllers in total, not spinning. Plugging around suddenly the chain of 10 spinning. But … unplugged from controller … only powered by stabilising sata. I then only used 1 triple … same … no spinning, no RGB. Plugging whilst powering I realised they spin when power cable inserted, but switch off as soon as locked. Same with TL LCD single. Whilst doing the inserting and locking … RGB flickers on in one corner closest to power cable. As new build I cannot install windows and cannot install L-Connect 3, cannot upgrade firmware. But that non LL fans work, fans spin via sata (not linked to controller) it looks like controller linked. Cannot get into bios as error message CPU … of course … cooling does not work. Any thoughts? Lian Li support is non-existent as most complicated contact forms. The AL/SL I had before were plug and play … working straight away out of the box!

[@Niclord7]

The cable that connects to the LCD fan is really lose. The hooks don't snap tight in place. So with some movement of the cable the connector just glides out from the fan again. I get the feeling I have to glue the connector in place to have it secure. The hooks are not bend or anything. Dissapointed in the quality. For the price it is not ok. I see your also popped out when moving the cable at 1:00.

[@andreamitchell4758]

Wait so this uses a SATA AND a pcie power connector! And I need another different hub than for my 120inf infinity fans? I just wanted to buy one for the exhaust fan on the back of my case so I still need to use both SATA and pcie? I already have 2 sets of inf120's and a hub for each set of 3 since I am using signal RGB and it says to have only 3 lian li fans on one controller. Plus I have 2 non lian li strimmers from airgoo. I am afraid I am going to run out of 5v ARGB headers and SATA power as I have some non nvme drives. The strimmers come with 5v argb hubs but I am not sure if I can use them for this controller. And my GPU uses 3 pcie 8 pin(6x2) I know there are 2 more for the MB/CPU and I have them both connected but I think I only need one as I only have one CPU, 12700k Is this correct can I use just one 8 pin for the CPU/MB? It is an a Z690

[@GanymedeXD]

A lot of false info here! Inform yourself from reliable sources like manufacturer webpage instead of comment sections! There you find all info! You do NOT need sata & PCI-e. Only if you use 6+ TL fans per port. The max for LCD is 3 any way. TL needs the TL controller … common sense as it also controls the LCD. Infinity needs SL controller. And no … strimer do not go on to the TL controller … especially no non LL strimer. If you do not want RGB to be handled by mobo you do not need to use the 5V controller RGB cable, simply doing it via L-connect 3. The hub is powered by one PCI-e cable. If your Intel processor needs 2 ATX cables your Intel manual will tell. My AMD only needs one as I am not overclocking. You need to check if you have free 8-pin ports. Despite having an ATX 3.0 PSU I got my GPU connected via 3x8-pin. But despite this, ATX power cable and powering 2x TL Controller I still got 3 free 8-pin ports. What does signal RGB mean? 3 Infinity per controller? Maybe per port … I was using RGB and 16 fans via one SL controller. So 3 sounds odd … especially for LL where 10 TL fans for example can go to one port.

[@andreamitchell4758]

@@GanymedeXD thans for the info signal RGB is software that works with difterent ARGB devices from different manufacturers and syncs it all together, the thing with signal RGB is that all other RGB software needs to disabled or it causes conflicts. yes I know you can't plug 3rd party strimmers into lian li hubs, didn't know that L hub doesn't support strimmers though. lian Li strimmers need you to connect an Arduno leonardo to work with signal RGB and you needed to upload cod to it and wire it, it's a complicated project so I went with 3rd party ones. signal RGB software also recommends no more than 3 or 4 fans per lian li hub to get full independent control you can have more but thy will just mirror the behavior of the first 3 fans. I thought I heard that lian li was also coming out with new LCD fans maybe those will be for Sl hubs then. you should check out signal RGB it can do lots of cool effects

[@VickyLatorreArt]

Why do I need to download "Microsoft Visual C++" to use this Lian Li fans software?

[@GanymedeXD]

So it runs stable! Clearly documented on LL webpage!

[@yeeree3398]

does anyone know when its coming to canada

[@jeanbiroute]

I don’t understand why you need to plug the pwm and rgb to the motherboard if they are already connected to the box and it’s connected with usb.

[@GanymedeXD]

You must do it to control fans snd RGB via your motherboard if you want to.

[@Mapantz1]

Why is the runway affect not working right on the bottom 3 fans? I've seen this in several videos now.. I'd take a guess it's down to the abomination software that is L-Connect 3? That's the reason I won't buy another Lian Li product that uses it.

[@ChristopherFlannigan]

It's beta software, hopefully any issues sorted by release

[@Mapantz1]

@@ChristopherFlannigan Beta? It has been available for general download for over two years. It doesn't say anything about being beta on the download page. The beta testing was done by a 'select' few because I can remember a conversation about it on Reddit. It's still awful even after all of this time! Some users are not able to control their new LCD AIO due to bugs in the software. It's unacceptable to keep releasing hardware that relies on it, and not bothering to fix the current problems with it. The mere fact that they have two different versions on their site - for users experiencing "problems" says it all. It needs to be scrapped, and a proper dedicated team of developers need to work on something new.

[@GanymedeXD]

@@ChristopherFlanniganIts not beta software … its the software used for all products.

[@123-g1u]

Can i use them as a cpu fan i mean 2_

[@mmedo155]

Do I need controller for only one lian li TL LCD fan?

[@GanymedeXD]

Of course … otherwise you cannot connect it and cannot control it. It requires TL controller! Only for TL fans!

[@UnKnOwN-hj5uc]

I actually dont know what to do anymore i tried everything i even bought a new controller and new fans (uni fan tl lcd) but the software still cannot detect them. (it can detect the AIO and the SL Infinity)

[@iifrowny-5407]

I know a fix for you

[@UnKnOwN-hj5uc]

What is the fix?​@@iifrowny-5407

[@UnKnOwN-hj5uc]

@@iifrowny-5407 what is the fix?

[@GanymedeXD]

A minimum of information would be great … you provide none and expect feedback? Do they spin? RGB? LCD? How does your setup look like? Buying new controller is pointless … I stumbled into problems and had an excess of 5 controller available. No change. Did you update the firmware? Correct number of fans per port and controller (3, 9 LCD)? Do you have pwm cable connected? Do you have ARGB cable connected? L-Connect 3 does not like other software to control RGB. I had to delete armoury crate. If you only use L-Connect for fans you could try unplugging all but usb and power. Some managed with bios upgrade.

[@UnKnOwN-hj5uc]

@@GanymedeXD It took me a month to figure it out tbh, but all i had to do is a clean windows installation.

[@trackmedixuk]

Is the new hub compatible with the uni v2 fans ?

[@SweetLou0523]

From everything ive seen, sadly no. The tl fan controller only works with the tl and tl lcd variants.

[@trackmedixuk]

@@SweetLou0523 Would it be able to connect directly to motherboard with all functions working the same

[@GanymedeXD]

Of course not! Its a TL only hub!

[@MrFreakyTv]

Name of screwdriver ?

[@johnc-jq1vj]

I cant get the wire that comes from the fan to the controller to stay. What are my options anyone? I know you are supposed to move the wires to the lock but it wont stay for me no matter what now.

[@GanymedeXD]

I got 36 of those dans and they all lock properly. Check if you have done it properly … insert, move to lock position. If this does not work exchange the fans if a different one is more firmly licked. If all fails you must return them!

[@evanrodriguez4234]

What’s the max amount of fans I can have animating at once?

[@GanymedeXD]

This you will not find documented anywhere. The limit there are the number of controller you are willing to use and how many ports you got available for RGB, usb, PCI-e and fan controller. One controller can manage 9 LCD fans. Means that will be manageable. Adding another controller you can add 9 more … thats 18. How many do you need. Only LCD looks pretty crappy. Good for accents of 3-4, but more look ridiculous.

[@evanrodriguez4234]

@@GanymedeXD I only need 10 max all powered at the same time, what would I need for that?

[@antoninococozza57]

ragazzi chi mi puo aiutare non riesco a far cambiare i display forse sto sbagliando qulcosa mi mandate il link esatto per il software delle tl display

[@GanymedeXD]

Its L-Connect 3 … just go to LL TL LCD and you are made aware pretty quickly !

[@murateksi3836]

I have a galahad II LCD and screen doesn't work with the software. I tryed different version of L- connect but same. I paid 450 USD for lian li logo :) Are there anybody living same problem or can fix it ?

[@alishayegan7953]

bloody hell, I do not have a free pcie cable, why pcie?? what is wrong with Sata?

[@GanymedeXD]

It does not matter … they decided to go for PCI-e and sata combined. Have you already upgraded to ATX 3.0? The problem is that many people buy power hungry GOU’s but do not upgrade their PSU … ATX 3.0 is specifically for those power hungry GPU’s. With 3x8-pin for GPU and 2 TL controller installed … still 3 free. Surprised so many run out of ports.

[@Andy.Jimenez]

The amount of Lian Li controllers you'd need is kind of annoying. They should release a controller that could connect the LCD Galahad cooler, SL Infinity Fans, TL LCD fans and Strimmer V2 Cables. You'd basically need 4 USB ports just to control all of these smfh.

[@cloggyable]

Cant believe Lian-li force us to buy multiple controllers for different fans, super disappointed. I have SL-unity fans, bought 2 LCD ones to show temps with and they aren't compatible, rip me.

[@GanymedeXD]

Thats not down to LL … if you want to combine completely different fans … like TL LCD with SL … how do you expect them to fit with the same hub? Its something you must consider before planning your build and if you want both … bite the bullet!

[@Mike-hs8fq]

@@GanymedeXD they should have made all the connections the same and not having to buy different controllers due to plug configurations

[@tsushima33]

Great video!

[@nikenzzo]

I dont even want ask the price …btw i am happy with arctic 9euro each …

[@nicholasevans9039]

WARNING: If you buy the pack of 3 you CANNOT use the fans individually. You can only use them connected together because there is only 1 connector to the controller. If you need to use them separately then good luck finding a connector to buy because I have not managed to find them sold separately. I believe the only way to get your hand on an extra connector is to buy extra single fans. You pay top bucks to get their best fan product only to find out you are limited in how you can use it. Lian Li is treating its clients as if they are naïve. I felt cheated to say the least after buying the 3-pack UNI FAN TL LCD. Lian Li sells something that can be used in 3 different ways (3 fans together OR 2 fans together and 1 fan separately OR 3 fans separately) but they give you only 1 connector. So, they essentially limit you to 1 option. I needed 3 fans and now I have to buy a 4th one but only use 3. Lian Li has to find another way to boost sales than treating their clients like this.

[@Mike-hs8fq]

Agreed they are screwing the customer

[@drshoots101]

Frustrating I didn't think about buying the lcd fans in reverse. You only mentioned the bottom ones was in reverse and don't say if the 3 on the right are? I'm guessing they are, judging of the way the blades look.

[@GanymedeXD]

Any fan front sides you see inside the case of intake fans are reverse fans. Just common sense … front and bottom are usually intake fans. You see them, they are reverse. Either you use yours as outtake fans or return them. Otherwise they are useless as LCD …

[@b.buster.]

you didn't show how to open the screw holes.

[@GanymedeXD]

😂 Good joke! Just remove silicone caps.

[@PowGetRekt]

A pcie 6 pin tho.. interesting.

[@m4_byb269]

These fans are trash, it kept turn off time to time no matter how I reinstalled the software/update it, no support at all , (I’m using 7800x3d CPU) , wish that I’ve got the Corsair instead.

[@Mike-hs8fq]

I feel the same way. Nothing but issues

[@MIMCKMedia]

This is the 2nd most boring video of these fans I've seen so far

[@normanosland8693]

to be fair to Chris, it is not his fault, he did his best with what he had to review......

[@MIMCKMedia]

@@normanosland8693 nah its totally on him 😅

[@bignicnrg3856]

I luv how people who can't afford just bash these fans. 😂😂😂

[@MIMCKMedia]

@@bignicnrg3856 i don't bash these fans and already ordered them

[@awesomeruben]

​@@bignicnrg3856 Lol right, let alone watch multiple videos to continue to bash on them