Power Transformer - 3D Animation

[@LifeAda]

Learn 3D Animation Beginner to Expert Level - lifeada.graphy.com/courses/3D-Animation-Basics-to-Expert-639c5862e4b0dc827dd3c47c

[@mdsajjad837]

W

[@hariomkumar3449]

Sir I m pcm student transformer is in my syllabus. And nice explanation I have understood transformer for this video

[@aishwary701]

Sir kya mera phone agr transfarmer k pass leke jau toh charge hoga ??

[@vsofficial8876]

Hame Konsabhi Transformers Step Up OR Step Down Ke Liye Use Karte Hai Isliye Or one Side High voltage Rehane Ke Wajhase Opposite Side LT Side Opposite side hoti Hai Sahi Hai Kya Sir

[@vsofficial8876]

Maine 10MVA Ka Transformers Khola Hai 400kva yeh Normal Hai

[@kalpeshdafda6511]

7:14 transformer secondary side and transmission line don't carry neutral wire ... It is earthing wire provided for safety against lightning. Step up transformer are always star to delta connected at power generating end.

[@rahultrivedi1923]

क्योंकि ट्रांसफार्मर को न्यूट्रल वायर की आवश्यकता नहीं होती पर जब ट्रांसफार्मर से हमारे घरों में बिजली आती है तब न्यूट्रल वायर की आवश्यकता होती है इसलिए कास्टिंग बचाने के लिए न्यूट्रल वायर ट्रांसफार्मर में नहीं दिया जाता😊

[@धनंजयगायकवाड-फ2झ]

आपकी वजेसे बहुत कुछ सीखने को मिला है बहुत बढीया है थँक्यू सर

[@putuo-transformer]

Great 3D introduction of the power transformer! Learn a lot from it!

[@kanjibhaidesai8893]

सर,ट्रांसफार्मर का सिस्टम बहुत कॉम्पलीकेटेड है, आपका समझाने का तरीका बहुत बढ़िया है, जिसमे एनीमेशन का रोल बहुत बढ़िया होता है | मेँ गुजरात का एक किसान हु मेरे खेतमें बोर पर 100HP सबमर्शीबल मोटर चलाने के लिए ट्रांसफार्मर है, ➡️ इलेक्ट्रीकसिटीमें ट्रांसफार्मर का क्या रोल होता है और कैसे काम करता है ये जानने के लिए ये वीडियो बहुत super great है.. 👍धन्यवाद सर

[@deepakchahal2145]

We use different connection both side of transformer. # Because if we make star connection both side of transformer it will be highly unstable # In star- star transformer there is problem of oscilating neutral condition # If we make star -star transformer it will be failed if load becomes unbalanced then star-star transformer not work. That's why we don't make same connection both side of transformer. ~NOW PIN IT😊~

[@chiradeepbanerjee2229]

Reason for Opposite Connections: The reason for having opposite connections (delta on one side and star on the other, or vice versa) in transformers is related to achieving a specific voltage transformation and maintaining a certain phase relationship between the primary and secondary sides. This practice is done to nullify the order of phase shift in a power transformer. When electrical power is transmitted or transformed, there is a certain phase shift between the primary and secondary voltages and currents. The magnitude and direction of this phase shift depend on the winding configuration of the transformer. In a power transformer, the winding configuration influences the voltage and current relationships between the primary and secondary sides. By connecting one side in a delta configuration and the other side in a star configuration (or vice versa), the phase shift introduced by one winding is compensated or nullified by the other. The specific reasons for this practice include: Voltage Transformation: Transformers are designed to transform voltages from one level to another. The winding configurations determine the voltage relationships. The opposite connections help in achieving the desired voltage transformation. Phase Relationships: The phase relationships between the primary and secondary sides are crucial for the proper operation of power systems. The opposite connections help maintain the required phase relationships, ensuring that the output closely follows the input in terms of phase. Harmonic Circulation: The delta connection in one winding allows for the circulation of third harmonics and their multiples. This is particularly relevant for power systems where harmonic content needs to be managed. The star connection on the other side may provide a neutral point, contributing to a balanced system. Flexibility and Application: The opposite connections provide flexibility in adapting the transformer to various applications and system requirements. It allows the transformer to be versatile in handling different voltage levels and current capacities. In summary, the use of opposite connections in transformers is a deliberate design choice made to control and manage the phase relationships, harmonic content, and voltage transformations within the electrical power system. It ensures the efficient and reliable operation of the transformer in various applications.

[@aqsa005]

chatgpt

[@khalnayak1361]

​@@aqsa005😂😂😂😂😂

[@thisisamanali]

​@@aqsa005😂

[@rahulmoirangthem9395]

The only main reason is to get sinusoidal flux and sinusoidal induced emf…

[@VishalGupta-q4z]

chat gpt boy😂😂😂😂

[@aanandkumar9740]

Easy language mai answer hai harmonics (odd) ko reduced krne ke liye ❤❤❤❤❤

[@TeslaTalk24]

"Thank you so much for sharing your knowledge and passion! Your videos have been a huge inspiration for me to start my own channel, TeslaTalk, where I’m diving into electrical engineering topics and practical troubleshooting tips. I’m excited to share what I've learned with others, just as you've inspired me. Keep up the great work - you’re helping so many of us take that first step!"

[@Rexton_98]

As an electrical students it's very common question for us 😊

[@Im_imran_66_YT]

Ans?

[@Chandradeep-i1z]

In a transformer, placing the primary and secondary windings on opposite sides of the core maximizes magnetic coupling and minimizes leakage flux, making it more efficient.That architecture also ensures accurate voltage insulation, which absolutely crucial to safety -- and at the same time aids in heat dispersion by offering better access for air cooling.Moreover, it simplifies production and maintenance by giving easy access to windings.The layout helps reduce fingering rivulets, which start crosswise after regular current is stopped but before stray electrical fields leave.Overall, this arrangement has made the distinction between buying and running costs very clear: medical device manufacturers say that while they might be able to recover their initial outlay through equipment performance over its expected lifetime, that is no guarantee of competitiveness.

[@_sharma_2666]

Apki video lazawab rahti hai sir kasam se maja aa jati h ❤️🔥🔥 kash aisi education hamare college vale dete lekin unhe to apni salary se matlab h 💔💔💔

[@yogeshvasurkar3297]

I like the way you explain and animate. And your cource is also affordable... Thank you bro

[@230V-50Hz]

Complex topics can be very easily understood when visualized in 3d.. this video is a perfect example of that

[@sureshbagheld6323]

Sir. Aapke 3d animation wale video to sabse jyda diply tk transformer ka sabhi bhag smjh aa gya or bhi electrical se related 3d animation wala video orr bnaiye sir. Aapke video se mai competitive exam nikal paunga lgta hai thankyou so much sir.❤

[@MR.4DFOXALBERT963]

Because 3 phase High voltage ko deta connect karke hi kam kiya ja sakta hai varna star connect kia jai to neutral connection nahi melega safety purpose keliye😊

[@gauravns007]

kya bol Raha hai bhai

[@HostelMania143]

Hm mainly transformer ko step down voltage ya step up purpose ke liye banate hai aur hm jante hai jab power transformer ki bat ki Jaye to high voltage side Star me hota hai jisse ki ham use grounding kar ske jisse hone wale nuksan se bacha ja ske aur In case step down transformer hm low voltage side Star connection use karte hai Jo usually hm grounding bhi karte hain aur use hm consumer ke liye neutral ke form me karte hain thats it

[@farukpatel3049]

transformer mai oppsite connection is liye karte hai ke 1- foult impact of primary to secondary and step up and primery high voltage side bahot sare alag alag feeder connected rehte hai to baki sabko effect na ho isliye secondary mai star winding use kiya jata step down transformer mai aur 2-winding ka phase angle 30 deegri displacement aur 3-earth foult detectinon ke liye aur 4-flouting nutral consetion 5-harmonics detroration 3rd and 5th

[@besomethingunique7407]

Very good teaching style sir Thank you 🙏

[@sonyvarghese198730]

What an amazing way of teaching ❤ awesome video. Very detailed.

[@Q-gk9kh]

Neutral point ke liye Star connection Kiya jata hai. Kyunki gharo Mein single phase line Jaati Hai To vahan per neutral ki avashyakta padati hai...

[@SouthIndianmoviesfree-go3hy]

Kyuki agr normal poll transform ki bt kre to input line delta mai is liye hoti hai kyuki agr by chance 3wire mai se koi ik Tut jae to koi problem na ho kyuki Bina natural ke. Current travel nhi krega. Or output mai isliye star connection Kiya jate hai kyuki hmare Ghar Mai aane wali line ko natural jruri hota hai to hme transformer se milta hai 😮

[@TrueWorldshome]

आपकी वीडियो से बहुत कुछ सीखा मेने थैंक यू sir ji 🙏🙏🎉❤

[@mansoorqazi3582]

Amazing video. You did a extraordinary job. thanks

[@ShriPhotographyOfficial]

Ans: In the Transformer, the primary and secondary windings are connected in such a way that they create opposite magnetic fields. This is done to induce a voltage in the secondary winding that is proportional to the primary voltage, but with the possibility of adjusting the voltage level through the turns ratio. The opposite winding direction ensures efficient transfer of energy from primary to secondary, based on electromagnetic principles. Please Pin🙏

[@trazergaming958]

Sir 1 no video hain mein wireman ka student hoon. Really aap hamare classteacher se accha sikhate ho

[@bkyadav2482]

@LifeAda agra transformer ka dono winding star star me hoga to harmonics problem aayega so ek alg se tertiary winding lagana hoga And agar dono delta delta me ho to isme phase voltage and line voltage same hota h aur koi neutral terminal bhi nhi mil pata h so iska application bahut kam hi hain🙏

[@prayagsingh8692]

We use primary side delta and secondary side star connection in step down transformer bcz the main reason is cost reduction of transmission line .... We all know know that secondary side terminal connected to our load (home appliances or any other thing) and we need a netural to complete the circuit... But in transmission side it's not mandatory.

[@vission80_yt55]

Wireless charger main transformer 230V AC se step down karke 5V AC karta hain, or us AC supply ko rectifier se AC to DC convert Kiya jata hain!!!

[@shaikh.taha.]

Why Transformer one side connected opposite to other One? Answer : In transformer winding, the primary and secondary coils are wound around a common magnetic core. The reason for connecting one side opposite to the other is to create a phase shift between the primary and secondary voltages. This phase shift allows the transformer to step up or step down the voltage, depending on the configuration of the windings. It's a fundamental principle of transformer operation and helps in transferring power efficiently from one circuit to another.

[@sahilmonitored]

Excellent video Sir monoblock motor ka water seal kaise Kam Karta hai iss par ek video banaye please........

[@LifeAda]

sure

[@mukeshchaudhari7292]

Distribution tfr me lv side me 3 ph 4 wire systerm use hoti hai normally agar tteno ph hi denge to single phase supply nahi mil payega isliye distribution tfr me primery delta. Me aur secondry star me connect hoti hai

[@satendrakumarkushwaha4446]

Ans is rectifier Although mobile also uses filter ckt transistor etc for waveform smoothing.

[@l11_ee_rohankumarsah26]

high voltage connection in delta because we can't provide so much phase angle that because we insulated the conductor in delta connection and low voltage star connection because we can provide normal phase angle thera no fault and no need of insulators in conductor this very cost effective for us. thanku sir for providing like this type of video for us❤😊

[@sudhanshusrivastav4837]

Sir Please ek video testing of transformer pe banaiye plzz,.

[@letmesee081]

In Power transformers the low voltage winding is generally placed near the core. You have shown the opposite in the video.

[@Technovation07]

@LifeAda In Transformer primary side is connected in delta side to high voltage and low vtg side connected in star because in star connection we need to balance the 120⁰ phase difference, a neutral point helps to balance phase difference between each phase voltage thats why connections are always in opposite direction

[@sec-ci9rj]

Bhai star m isliye rakhte kyuki star winding m hme neutral mil jayega jo hme phase ke sath neutral b chahiye hota h

[@naveenyadav3790]

Transformer me Primary side delta me aur Secondary side Star me connect krte hai - Harmonics ko reduce krne ke liye

[@AbhishekKumar-cp6cz]

Step up transformer me star connection use hota hai kyuki star connection me voltage, root 3 times of phase voltage hota hai thik waise hi step down ke liye delta connection use hota hai

[@VikashKumar-rc1ug]

Thank you sir mera doubt clear karne ke liye

[@sciencefictional6052]

bcz delta side high tension power supply hoti hai usme delta connection hote hai or convert hokr hme star system milta hai jisme neutral bhi hota hai

[@Gouranga_kun10]

Better than College ❤

[@nazimali1632]

Because of there are two windings 1 is primarily 2 is secendry Transfarmer is only two types 1 is stepup 2 is step dawn Both are opposite two each other So I windings in delta 2 windings in star

[@pawancreationoffical]

It is depend upon a load Balanced laoad in a system that time can be use delta connection Unbalanced load we are use star connection But the maximum chances the load is not balanced

[@Kishanyv777]

For easily distribute 3 phase sequence and 4 wire system. So we connected T/F coils in Delta and star connection.🎉🎉

[@sushantdey402]

One more safety of power T/F is Nitrogen injected fire protection system 😊

[@Simpltarget]

Hai voltage me kabhi neutral nahi hota hai kyuki Transition line me upar wala wire hmesha 7:14 earthing ka hota hai 😅

[@toxicfreevoice546]

Always opposite connection hoti he first reason is transformer ko hum kabhi same rating ke liye use nh krte ya to Hume step up karna hoto ta he ya to step down means ya to transmit karna hota he ya to distribute agar transmit karna hoto hum alway 3phase main hi karenge and 3phas main always delta hoti he agar distribute karni hoto star connection karenge because Hume 4wire system ki jarurat he kyu ki 3 phase ke satt neutral bi chahiye SO HUMARA NEED KYA HE WAHI HISAB SE CONNECTION KI JATI HE STEP UP STEP DOWN (transmit or distribute)

[@electricalpoint]

Bhaiya agar aapka primary side delta hai aur aapka secondary side agar star hai matlab aapka voltage step up ho raha hai, aur vahi agar aapka primary side star hai aur aapka secondary side delta hai matlab ka voltage step down ho raha hai, donon side opposite connection isliye hota hai taki aap voltage ko step up step down kar Sako😊

[@abhishekparida2004]

No harmonies loss ka Baja Sa Kia jata ha asa😊😊

[@sachinkumar3233]

U wrote wrong. Learn deeply about transform connection

[@maheshkush12345]

In railways AC coach 60kva transformers are use in which primary coil high voltage 750 volts 3 phase connected in delta connection & secondary coil low voltage 415 volts 3 phase & 1 neutral connected in delta connection...

[@AnshuKumar-sh1ns]

Star and delta type transformer ki vdo bnao Zigzag bhi

[@birendrabhue1917]

Star delta connection hota hai kyun ki consumers ko neutral ka v jaroorat hota isliye secondary side m star connection hota hai

[@Creative_Boy002]

Question = why transformer one side connected to other side? Answer = The reason is that the high-voltage side voltage is the generator outlet voltage, and the high-voltage side winding of the excitation transformer is connected in a Y-shaped manner, with a phase voltage of 1/√ 3 of the line voltage.

[@RaviKumar-en3zu]

best video seen about transformer

[@kushwahasantosh8281]

Sir ek ship kase work karta h please explain ( Oil contain ship)

[@naitikpatyal]

Bro iss video ke baad mein sach mein TRNFORMER dekhne chla. Gaya😅😅😂😂😂par darr bhut lg rha tha paass jane mein

[@vk-viku]

The primary winding, also known as the input side, and the secondary winding, also known as the output side, can be connected in different ways to achieve the desired voltage and current levels. When the windings are connected in a star arrangement, or Y-connection, the voltage between any two of the three wires connected to the windings is the same as the voltage in the windings. This connection can be used to produce a lower current, with the same voltage as the input. On the other hand, when the windings are connected in a delta arrangement, also known as a Δ-connection, the voltage is across each winding is less than the voltage of the input sides. This arrangement can be used to produce higher currents with a lower voltage.

[@pabitraswain4781]

No

[@night_reels]

In delta there is absence of neutral point whereas in star their is neutral point and also the neutral is then grounded to the earth

[@Katter_hindu_boy]

वायरलेस चार्जिंग मोबाइल फोन में एक स्टेबल एक तो डीसी कनवर्टर लगा होता है जो बैटरी को चार्ज करने के लिए करंट को आगे भेजता है❤

[@respectisfast9272]

Maine Power grid mein dekha hai 400kv & 500kv ka Transformer

[@aadishaktiautomationelectr165]

❤❤❤ aaj apne hi bahot kuch sikha Diya he

[@shalendrasingh9426]

Kya gjjb ki knowledge di aapne animation ke jariye

[@Jack-bk8hj]

Apki Videos Bahut achhi hoti he aesi aur bhi videos banaeye 🔥🙏

[@npsskcreation5094]

Kyunki ki distribution transformer me hamesha volgate ko ghataya aur cirren ko bdhaya jata hai. Chuki ham jante hai ki star-star connection aur delta -delta connetion me volatage aur current constant rahta aur star-delata aur delta-star me voltage aur current change hota hai isliye hamesha transformer me dono opposit connection use kiye jate hai 8:13

[@UttamrajSingh-z1e]

Diod and rectifier se ac / ko DC current converter kar deta hai. Hai jiske filters ka use Kiya jata hai ❤

[@himanshu_phukan]

8:07 Bcz the transformer has connected to opposite direction bcz it's has phase difference in input and output voltage .

[@sharadsonawane8182]

Badhiya video banaya he ❤

[@killershow3806]

Alon + 🌃 2AM + Rain + 🎧 + Lifeadda = Sukun❤❤

[@gouravmiishra]

😂😂😂

[@abhidhurve.........3014]

Very nice video ❤❤❤❤

[@LifeAda]

Thanks 🤗

[@TS_VIKRAM]

Transformer me star wdg me ek neutral wire milta h and usme kam current flow hota h jabki delta wdg me neutral wire nahi hota h or current bhut jyda hi flow hota h wdg se

[@rahulmaurya2668]

High voltage se low voltage & low voltage se high voltage me convert krne ke liye opposite connection kiya jata h. Like (star to delta or delta to star)

[@TS_VIKRAM]

Charger me ac supply jab jaati h toh usme electrical device Rectifier hoti h jo ac ko dc me convert kar deta h

[@fakefriendsfakefriends-gq9gj]

Thanks Bro ❤❤

[@Shivamyadav_vlogs_786]

EMF is in the secondary side is induced due current flowing in the primary side

[@murlikhara8489]

Good explained sir

[@rizwankhan-pz8eb]

Love you lifeada

[@VishalKumar-np2gs]

animation ki vjh se concept ko smjhta aasan ho gya

[@priyanshuranjansahoo]

7:13 you are wrong brother High voltage side side pe generally delta connection hota hai . Star nehin to neutral kahanse ayega ? Wo jo wire hai wo shielding wire hai to protect the transmission line from lightning.

[@motivation_updates]

we use Delta - star connection for step up transformer as voltage is reduced by √3 times in star connection.

[@pradip746]

You are a Good Teacher

[@amitchandel8016]

बहुत ही इनफॉर्मेटिव videos ❤thanks

[@RumanMemes]

Make a video on central Ac Plant

[@SharvanPandey-y1g]

Sir ek dusre ke oposite rahega tabhi magnetic fild genrate karega

[@mohansingh6810]

Good information

[@sanjeevkumar.9]

Because star connection is high voltage with respect to Delta connection V=Vp/rute3 7:49

[@FinancFamily]

Theory is easy But please explain the phasor diagram of loaded and no load cases of it practically In ideal and practical thansformer

[@kshitijshrivastava2258]

Very good video

[@partner-xq9yl]

Because lower voltage pe hum 1 single load bhi connect kr skte hai toh neutral return path provide kr deta hai

[@GoodFansSTATUS]

Third harmonics ko km karne ke liye Ek side star connected hota hai Dusre side delta connected hota hai

[@giyasuddinansary5332]

Very good 👍

[@leovicky7]

Very good explanatio

[@giyasuddinansary5332]

Very good

[@rajeshdeswal6573]

In Phones we can convert AC to DC by using transistor,diode. ❤

[@Khushal435]

Transistor and diode never convert AC to DC , a rectifier is used to convert AC 240 volt to dc 5 volt, or 12 volt.

[@srnsrn6741]

​@@Khushal435lol.. rectifier is made by using diode only.. n diode never convert 240 to 5,12v dc.. it is done by using step down transformer..

[@bhaiti1198]

@@Khushal435 rectifier make from diode .

[@pakistanigamer3050]

​@@Khushal435Fun Fact . He studied about Bridge Rectifier Before Studying About Diode.

[@subhashisdas6254]

@@srnsrn6741 How can a step down transformer convert 240 volt AC into 5/12 volt DC...??? 🙄🙄

[@rklongelectronic]

Very true helpful video sir

[@Suman8888steno]

Very well explained

[@tushargupta2741]

Insulation cost ko kam rkhne ke reason se dono side ka connection alag alg rhta hai

[@hammadasad5887]

Very Good

[@deepakchahal2145]

In distribution we need of a neutral wire for close the circuit so we use star connection in LV side of a transformer bcz in star connection a neutral wire also present. but in delta connection there is no neutral wire .

[@md.abdullahtalukder5047]

ডেল্টা কানেকশনে কয়েল প্যারালাল সংযুক্ত থাকে যার ফলে কম ভোল্টেজে বেশি পরিমাণ কারেন্ট প্রবাহিত হতে পারে। এবং স্টার কানেকশনে কয়েল সিরিজ কানেকশন হয়ে থাকে যার ফলে অনেক ভোল্টেজ তৈরি করে কিন্তু এম্পিয়ার কম হয়।

[@surendrasahu8436]

Super sir ji