LINX 3.0 - 05 | Blink!

[@feed87]

How to include a LINX target in the list?

[@ARSLANSAJJAD]

Hello Sam ! Can you please post a tutorial with analog read (e,g with LM35 temperature sensor) with beagle bone black ? I am using the same procedure you taught in this tutorial but I am some garbage values.

[@urssenn6217]

SAME HERE. "no memory information available" while deploying the blink - adv VI and then it stopps deploying with the message "LMH-LINX.lvlib:Local IO.lvlib:Load Device Channels.vi loaded with errors on the target and was closed." I'm also using Raspi 3. Any help appreciated!

[@mustafaaljumaili6279]

If I want to make the same example in this video but not using RPI GPIO directly , I need to use Arduino digital output after connecting the arduino into RPI by serial port, is it possible please advise

[@08Downhill]

Help please solve the problem with HC-SR04 sensor, when connecting the sensor to Arduino, does not determine the distance, after passing the terminal Read.vi the value is 0.00 E + 0 in Highlight execution mode (yellow light). For example, blink checked, everything works. What could be the problem? Connected components are all right.

[@feed87]

Hello Arslan, I'm using chipKit Max32. I run the Blink example, i uploaded the firmware. The only problem right now is my "Targets and Devices" list.... is very small, looks like I did not install something. Can you give a tip? Best Regards Fred

[@chethanchethu1093]

im getting an error that says "no memory information available " while i try to deploy the blink code as shown in this vedio what is the problem ? im using raspberry pi 3 B+ model

[@tomaszbieniek3774]

I can configure target with LINX and connect with RPI properly but during connecting I have conflict : "Unable to resolve from current dialog" please somebody help

[@maheshsrocks]

Same errors

[@maheshsrocks]

Fresh raspbian and manual installation and no error

[@MaxGoddur]

After seeing Labview used with the pi decided to search around for cost and was met with first off version show by year and either home or commercial editions. What version and edition are you using in this video?

[@ARSLANSAJJAD]

You can use either one but prefer home or student edition.

[@raheebali1]

Not working with raspberry pi 3b, deploying ends up with errors and connection gets lost, not connecting again then. Please guide.

[@labviewcourse4524]

i got the same here in my raspberry , if you find somthing plz tell me i dont know how to solve it hopefully you got the answer

[@maheshsrocks]

If ur getting problem then go to ni website there is manual installation process do it u won't get error!

[@kano817]

How to run "Target and Devices" caption if I have only [New]->[New..] after right click on [Project: name.lvproj] ?

[@kopniczky]

i have the same problem :(

[@kano817]

Hey, Mark, likely the problem lies with version of LabView. If you'll install 32bit version the problem should be resolved. I've version: 64bit and I'll try to reinstall on 32bit. Give me info if that fix it. Thanks

[@kopniczky]

i also have 64 bit version, tell me if the 32 is working

[@kopniczky]

4) Using LabVIEW 64-bit: Currently, the LabVIEW Real-Time operating system only supports the 32-bit architecture. Therefore, the Real-Time Module will only allow targeting RT controllers using LabVIEW 32-bit. When using LabVIEW 64-bit, you will not be able to see the Targets and Devices... option. You are right, i foun this here: digital.ni.com/public.nsf/allkb/3B09AA84E6C7BAA386257A670055CE58

[@kano817]

So, we have to reinstall from 64 bit to 32bit RT? damn..