Liquid cooling MSI MAG CORELIQUID C240 unpacking, installation, appearance 👌

[@hazardousgamer6935]

Actually the MSI Coreliquid C series have their pump integrated into the radiator so ideally you wouldn't want it to be the highest point in the water loop to avoid any air bubbles forming into the pump. Your current configuration (pump at the highest point) might work well at first but in the long run, it's not a good idea.Better to mount the rad at the front as an intake and shift the front fan to the top as exhaust.

[@ben4mark]

That's true, but first of all we have three years warranty, and we don't want to violate air management, because the waterblock on the front panel will heat the air for the video card, which is also not very good

[@hazardousgamer6935]

@@ben4mark It's funny you say that. Actually Jayztwocents just recently got an Email from one of his sponsors declaring the same "The fans exhausting heat into the case would heat up pc components and will cause an early failure". So he got offended and made a whole video testing different configurations for radiators (as intakes and exhaust) proving his point. It's a good watch if you got time. I will link it here. Again the problem you are describing might be applicable on Mini-itx form factor where air flow is very restriced but with Mid Tower and Full tower cases ? Not at all. Radiators don't output that much heat as you might think that could heat up the ambient air around the components to cause any failure. You will see in the video that even in worst case scenario (yeah at the end he got crazy and set all 6 fans as intakes 😂), the ambient air inside case goes upto 30°C which is certainly not bad for any pc component. Even our body temps are higher than that lmao. Regarding your argument for the "3 yrs warranty", i mean that's one way to look at it. If you don't care about the life expectancy of your pc components and ready to take the risk of your aio giving up before 3 yrs and not after that then it's ok ig. Here's the link : kzbin.info/www/bejne/rnOXpmxtqLl1btk Have a good day :)

[@ben4mark]

@@hazardousgamer6935 👍👌

[@oibwankenobi]

Watch his GPU, he can’t install it at the front, from my side it’s the same, GPU is big in the case no letting enought spaces to mount watercooler at the front

[@jehadsridingvlog1397]

Ive bought this 2 days ago.. some says it sucks :( but im still observing ... hoping it wont suck coz it cause a lot of money

[@slawomirzawislak7385]

Super! I read this cooler is best For my I5 12600k need to buy it... Is this working without problems?

[@ben4mark]

it works without problems 👌

[@omerfaruk7680]

Are you putting something like rubber on the motherboard after you put the lga1700 kit on the pump?

[@ercanozdemir.]

I Have a Ryzen 7700 Processor. I Bought the MAG CORELIQUID C240 Liquid Cooling Model. I wonder what the difference is between the 240R Model? In which year were the products produced? I am Turkish. Help me. Thank you very much.

[@ben4mark]

240R loses its effectiveness over time and stops cooling. The 240R flaws have been fixed in the C240

[@torkil2639]

The aio block is sideways 😂 👍🏻

[@MrSimonjan78]

Hi mate. I have this unit as well but my Dragon logo is upside down. Can I rotate this CPU block cover somehow? I was trying to find some info but nothing useful. Thanks

[@ben4mark]

this dragon logo has any position normal

[@musazaid6666]

You can but be very careful not to mess up the thermal paste or get any foreign substances on the cool block while you rotate it. I repeat be VERY careful. You may have to update some settings afterward. I rotated mine as I was still building it( put it in upside down first) but it’s all good now.

[@Final_Action]

In the version without backlight, I flipped the logo 180 degrees, this is the only option. To do this, you need to carefully remove the casing with the logo and divide it into two parts. They are on latches. After removing the outer panel with the logo, you need to machine a groove on the edge. This groove is already on one side, you need to make the same one on the opposite side. It will need to be matched with the mating slot on the bottom frame. I think it will be intuitively clear :)

[@Di21.08]

Еще быстрее надо было провода подключать. Ничего не понятно

[@IAntKnees]

Is it compatible with Ryzen processors?

[@ben4mark]

Yes AMD platforms AM5 / AM4 / FM2+ / FM2 / FM1 / AM3+ / AM3 / AM2+ / AM2 Intel platforms LGA 1150 / 1151 / 1155 / 1156 / 1200 / 1700 LGA 1366 / 2011 / 2011-3 /2066

[@joanarades]

Hi, dose it has a software?

[@ben4mark]

I didn't use any software, everything works as is

[@Bkgamersv]

Why msi aio logo are not aline.

[@ben4mark]

not aline?

[@Simon_Electric]

I think I know what you mean. I'm attempting to mount mine to the top but the edge of the case is covering the MSI logo. The setup does come with those plastic feet/bumpers but I have yet to see anyone use them. That may be what there for, considering you wouldn't use them as a buffer between the CPU and the water block. Just a theory, I hope it helps.

[@Simon_Electric]

FYI, my setup came with no manual. Or paperwork.