Locating and accessing the hydraulic fluid screen on the Mitsubishi D2050 tractor.
Пікірлер: 27
@user-zy7rz3lk4s7 ай бұрын
not all are down there, some are under cap left of feet
@kiendiep2 жыл бұрын
Very good
@cicadarhythm57093 жыл бұрын
Just wanted to say I have a D2350 and I changed the hydraulic fluid and filter yesterday. Taking off the wheel is not necessary at all. I appreciate the video, but taking off the wheel is way too much work. Just get on the ground there is plenty clearance.
@Lowstarfarm2 жыл бұрын
Also it looks like the nipple on the inside end of your filter may be broken. Valley Power repaired mine.
@drgoatdoc6 жыл бұрын
Can you post a video tracing the piping from the hydraulic pump to the control valves and then back to the sump? I have a st2640 with only a three point. I have tapped into the hydraulics but it is rather sketchy as to my return pathway (i removed the dipstick and put a fitting in with a return line... Ill be watching
@user-cf2su1xv3n Жыл бұрын
I have a 1980 2650 fd how do i know when hydraluic fluid is full
@eadgbe335 жыл бұрын
Hi! I have 1801d and I'm not sure where I need put the hydraulic oil... Can I show you by picture?if yes how? Thx u! Best regards
@billwall9307 Жыл бұрын
Hi Danny. Do you know what grade of oil goes into these Tractors?
@boomerboomer-rb6ns6 жыл бұрын
Thanks for the video. Do you have any more for this model. I just purchased a D2050FD and I could use any help you could provide. thanks again JB
@dannywhitley68016 жыл бұрын
boomer01 boomer01 I haven’t created any more videos on this tractor but if you have a suggestion for one let me know. Thanks.
@theuglypenny2 жыл бұрын
I need help also cleaned everything and pto still won’t come up if I have something attached to it
@jwchapko7612 жыл бұрын
@@theuglypenny could have air in it !! I had a similar issue on a Kubota… I covered the filler hole with a clean towel and my hand while inserting a blow gun pushing pressurized air into it! It worked then I moved 3 point up and down a couple of times…. Then repeated the process. Problem solved!! Good luck 🤞
@theuglypenny2 жыл бұрын
Mine was clean but hydraulics won’t come up when I have something hooked up to the pto. Any ideas?
@buddyboy19535 жыл бұрын
Hi, Do you know where manuals can be purchased ? I have a D2500 Mitsubishi Tractor, thanks
@hyzercreek Жыл бұрын
ebay. People make repro manuals.
@luciantic804 жыл бұрын
Anyone knows the rear tyre size for these xx50 generation? I have a FD so need to match the exact size. Currently has 9.5/9 R24 on the rears and 6-14 on the front
@emanuelbrown27952 жыл бұрын
Hi I have 2050 and can not get hydraulic to work already check filter put 4 gallons of oil in it until it started coming out bolt hole on side
@snapsaz60673 жыл бұрын
Interesting whre its posible to buy this fillter...:(
@wiraxpiese91335 жыл бұрын
hello did you have code for this filter
@CapeFrank574 жыл бұрын
Hello Danny, just bought a house that has a D2050 Can’t get it to go in gear, try to put it in gear and it just Grimes Any suggestions Thanks
@luciantic804 жыл бұрын
Mine sometimes gets stuck when I try to quickly cross shift from 2nd to Reverse. Gets stuck in 2nd if I remember well. Easy fix: unbolt the top cover of the transmission (the one with the gear shift knobs), move the forks in some position that makes sense for it, put the cover back on it and take care next time. Or never use the 2nd gear :))
@thIDthIRreenactor2 ай бұрын
Ik this comments old so you probably fixed the issue but for anyone else reading this it's most likely your throwout bearing going bad, to fix the issue you just gotta slow your rpms down and put in gear and quickly rev the engine back up before it shuts off
@lateresejohnson34912 жыл бұрын
I changed the fluid and my hydraulic still does not lift up. What do I need to do? Help!
@timothyjones604 Жыл бұрын
I have the same problem did u get yours fixed
@markochipsmarkochips38666 жыл бұрын
Do you know where I can get a filter screen for my mitzubishi 180 diesel. My screen on filter needs replaced. Thanks
@jaspervancalster28623 жыл бұрын
how to let it go faster i can't let it go faster then 10km/h :/