Log splitter seal repair, while in the field

[@LetsDoThis321]

The repair seals I used for this video can be found on Amazon: amzn.to/48KhlUd just be sure to measure your cylinder with a tape measure to see your buying the right size. I wish you the best of luck on your repair!

[@bobbysmith3196]

Best video I’ve seen on KZbin for fixing what needs to be fixed and gettin Right back to Splitting Firewood!!! Thank You Sir 👍

[@marthaking1269]

Nice video. I have the same splitter and it just started squirting oil out. Thanks for doing this video.. IT really helped

[@seancasey8594]

Thank you so much for this video. Very helpful. Worked perfectly for my Dirty Hand Tools 22 Ton.

[@remingtonsypro3160]

I have the same splitter you have why did you decide to rebuild the cylinder? I have lost some splitting power with mine just wondering if this is the next step. 50 /60 hours on it. Thx!!

[@seancasey8594]

The front seal cracked and was leaking. That’s why I ordered the kit and replaced the front seals. I did not replace any of the rear seals even though the kit came with those also.

[@damienrodriguez3288]

Good Lord! Thanks so much! I couldnt figure out for the life of me how to get the snap ring off😂😂😂

[@johneden9265]

Good Job! I have to do this exact same thing with mine. It beats having to forcefully extract the piston rod, and making a big hydraulic fluid mess. Thank You.

[@stacyboots8117]

Thanks been dumping oil everywhere trying to bust up a hundred foot white oak, it got worse today. Seal tomorrow. Thanks!

[@LetsDoThis321]

That is exactly the same boat I was in, darn thing was dribbling oil then it was pissing oil and I was like I got to get this pile split. Thank god for amazon 2 day.

[@remingtonsypro3160]

This is a great video very informative.. thank you

[@viktorkinah8981]

God bless you !

[@stevenallen2530]

Thanks for the part link, just what I need.

[@stevenallen2530]

I have the same splitter, 27 ton which I bought in 2015. I split several cord each year. My only heat source I have but I like it that way, wood heat is the best. The parts kit was nearly 28 bucks with tax. I decided to change the hydraulic oil and filter along with the engine oil. R&R the seals and ops check good . All said and done about 1.5 hrs and just under $120.00 bucks.

[@js7troy]

Must be something in the air......Mine blew today, thanks

[@LetsDoThis321]

There has been a number of folks thanking me for this video in the past couple weeks. Guess it's the time to get spitten before the winter cold draws in.

[@kevinlj3497]

Ditto. Exact same machine too.

[@js7troy]

@@LetsDoThis321 installed my kit today......only difference is when the piston pooped out, a gallon or so of hydraulic fluid came with it . thanks for the vid 100% helped

[@bobbysmith3196]

@@js7troy I have a 22 ton (Dirty Hands) that actually has the 4” Cylinder… Started squirting fluid about a week ago now🤷‍♂️🤣 Great Video!!! Best I’ve seen on KZbin by Far!!! Thank You Sir 👍 Well Thanks to… @LetsDoThis321 !!!

[@oggarage3459]

I dont own one but Am doing this for my neighbor next week he has the exact same one and is leaking badly, he doesn't feel capable of doing it, so he asked me, your video is gonna be very helpful thanks for the link to the kit.

[@kebo57]

Great video, I may be doing this pretty soon. My County Line 22T splitter has started leaking fluid from the front of the cylinder. Thanks for all the info, I may earn another KZbin Shadetree Mechanics badge, if I get er done!!! 😆

[@remingtonsypro3160]

I have a dirty hands 22 ton log splitter. What's not leaking any fluid in my fluids at the right level. I've noticed a loss of power splitting logs it won't split logs it used to go right through. Any thoughts. It really doesn't have that many hours on it splitwise. Maybe 50/80 hours. The motor runs fine I just wouldn't think that the cylinder rebuild would be needed yet. Is there any troubleshooting methods? Is there a way to bleed the air out if there's any are I'm not sure how we got in. Thx 🇺🇸✌️

[@LetsDoThis321]

Could be the rear seals passing fluid or it could be a pump failing. It is very possible you blew a rear seal in the cylinder. This video does not cover the rear seal. For the rear seal you have to pull the cylinder all the way out, it can get a bit messy if using hydraulic fluid to push it out, but it can be done that way.

[@remingtonsypro3160]

@@LetsDoThis321 thanks for your advice I appreciate that!! It's still splits it just seems like it lost 20 to 30% of it power. Be nice if there was some kind of gauge or something you can put on it to check it. To see what's wrong. Thx 👍

[@LetsDoThis321]

Yes, you can install a pressure gauge on a wood splitter, it should be placed between the pump and the valve on the pressure side of the pump. Order a T fitting and fit a gauge inline. The old splitter I used had a gauge on it like that.

[@kebo57]

Like has been said, it could that your hydraulic pump is going bad on that unit. Also, check the coupler that connects the pump to the engine. Those go bad and can slip, which makes it seem like the splitter has no hydraulic power. Good luck.

[@johnnyvanover3572]

Got mine on Amazon

[@bobbysmith3196]

Do You get a Commission if i use the link You provided but actually scroll or search to find and buy a 4” Seal Kit??? Sure Hope You Do!!! This Video was a Huge Help!!!⭐️⭐️⭐️⭐️⭐️

[@LetsDoThis321]

Looks like it... There were 10 ordered this past 5 days off that link, 3 were the exact link I provided and 7 were alternate seals folks found and bought.

[@TommyTorres-m3r]

Where can I purchase the seals for my 27 ton log splitter dirty hands log splitter

[@LetsDoThis321]

This is what fit my 27 ton dirty hands log splitter, be sure to check your cylinder size and it matches what your ordering.

[@TommyTorres-m3r]

​@LetsDoThis321 where did you purchase your seals and how will I know what kit to order

[@bobbysmith3196]

@@TommyTorres-m3r Hopefully You Have found what You’re looking for by Now but just in case… There’s a link to the Seal Set in his… Description of what he’s doing!!! Which he has a 27 ton (Dirty Hands) splitter that took a 4.5” Set of Seals… I have the same (Dirty Hands) Splitter except it’s a 22 ton that takes the 4” Set of Seals!!! Very Important to Measure across the cylinder to make sure You get the Correct Set!!! This is The Best Video I’ve Seen Yet on KZbin on Changing just what You Need to Change To Get Right Back to Working On Getting Your Firewood for the Winter!!!✅ I changed the Rear “Bearing” Seals and it’s Not always Easy to Get The Shaft Out of The Cylinder!!! Saw a video where the guy uses a forklift with the cylinder hooked to a metal pole to pull it out 😳🤣🤣 Good Luck 👍

[@Chucktales]

Where did you buy the seals from?

[@LetsDoThis321]

Amazon: amzn.to/48KhlUd just measure your cylinder with a tape measure to see your buying the right size.

[@CurtisKing-oh4nr]

Sho your magic then

[@LetsDoThis321]

I don't follow...

[@bobbysmith3196]

@@LetsDoThis321 Not sure i follow this comment either 🤔😊 Unless he’s saying… GREAT JOB!!! I thought so!!! Best video I’ve seen on KZbin for fixing what needs to be fixed and getting right back to Work!!! Thank You Sir for showing Us a Few Tips… Really Appreciate this Video!!! I’ve Seen one video where the Man hooked the cylinder up to a metal building pole and a Forklift to pull the Shaft out of the Cylinder 😳 I thought OMG what have i gotten myself into 🤣 Your Video made the Job Easy!!! Thanks Again and Have a Great Day 👍

[@mikei2322]

*Promo sm* 🎉