Part 2 Suzuki LT-4WD QuadRunner bearing installation

[@jameswaters4081]

Dude thank you so much I'm a gearhead but I pulled my four-wheeler apart a month ago and my job hit real hard extra hours so I needed something to kick my memory

[@LonnieJohnson1]

Your welcome, glad to help

[@jeffmurray5018]

Thanks for the video! Getting ready to do the same job on a 2001.

[@LonnieJohnson1]

Your welcome

[@dillonwest4236]

My bike is 1997 king quad, I've put new bearings in and when I put the stud plate into the bearings it won't go all the way home leaving a 5 to 10mm + gap towards the brake drum housing and seal? What do you think is wrong here please?

[@LonnieJohnson1]

It has to be centered and you might have to tap it in and is the bearings all the way in?

[@dillonwest4236]

@@LonnieJohnson1 I've taken it to the shop I don't know what's wrong with it

[@dillonwest4236]

So I took it to the shop and to my surprise a small ring of the old bearing had sheared off at stayed I side the housing! I couldn't see it but once it was removed and shown to me I was amazed and pleased it could be sorted! Cheers

[@LonnieJohnson1]

Glad to hear it wasn't nothing super bad.

[@SystemicKRASH]

OK how about the seals and bearings at the other end of the shaft, in the differential ?

[@LonnieJohnson1]

Well you have to take the differential apart and that would be another video. I do have a video of that but it on a 300 Kawasaki Bayou. Go to this link to see the Suzuki LT-4WD differential break down. www.ronniesmailorder.com/oemparts/a/suz/50d0b15cf870022c2c536431/differential-gear

[@zzzsleep3808]

Hey, I am currently trying to get my rear break drum apart but there is 5 Allen key screws that will not come off, would you know how to get them off so I can get the bearing out?

[@LonnieJohnson1]

R U working on the same type and year of quad?

[@petemartinez2316]

So I installed the bearing using another video. I installed it correctly however, I forget to put grease on the space. Is that going to be a problem or no? First time doing it so please don’t beat me up too much.

[@LonnieJohnson1]

Did the old part have grease on it when you pulled it out?

[@petemartinez2316]

LonnieJohnson1 no sir.

[@LonnieJohnson1]

If you mean the spline you should be ok, it should have had grease on the other end.

[@brandonmccall3929]

Whats the part number on the bearings

[@LonnieJohnson1]

BEARING (32X58X13) 09262-32023 You can find it on Amazon

[@LonnieJohnson1]

Here is a link to parts you might need. www.ronniesmailorder.com/oemparts/a/suz/50d0b166f870022c2c536450/rear-suspension-arm

[@sgtPhoenix53]

What size are those bearings, And where did you get them? My front ones have gone bad.

[@molinaroandsons3327]

hi and thenks for the video, could you give us the sizes of bearings and seals please?

[@LonnieJohnson1]

The bearing part # is 09262-32008 and the Seal or dust cover part # is 09238-40018 You can go to Ronniesmailorder.com and find any part you need for this and other ATV's

[@LonnieJohnson1]

Also the back seal dust cover part # is 09283-40019 both inner and outer bearings are the same. If you take your bearings and seals to a place that sells bearings they will match them up at a cheaper cost.

[@matthewloew2309]

Very helpful, thank you

[@LonnieJohnson1]

Your welcome

[@PerWiklund234]

Thanks for sharing

[@LonnieJohnson1]

Your welcome