LoRa GPS Tracker Tutorial | LoRaWAN with Dragino and Things Network

[@thatiotguy8837]

Great Tutorial. I would like to see turning this as a product, with standalone operation with battery. Seeing a system all together with battery operated and self charging system using Solar would be interesting.

[@CETech4u]

The LG-92 that I show in the video is somewhat that only!

[@rahulk04071996]

I really learn lot of things from this channel, thank you for making such hard effort and sharing your knowledge with us..

[@CETech4u]

Thanks a lot Rahul!

[@bartdereu9267]

Great, just what i was looking for !

[@richarddoyle5613]

Great content, very informative, kept in a very understandable format, keep up the good work!

[@CETech4u]

Thanks, do consider sharing and subscribing for more content like this!

[@eduandrz]

Hi, thanks to the video. One question. Isn´t necessary to "pair" the gateway with the sensor?

[@rakilachraf391]

It was an exhaustive explanation .. thank you! But I have a problem, how is it that I am using the same hardware for your code but the flash memory of Arduino Uno has been exceeded? could you please help me with that?

[@soumitradey8208]

Great video! Wonderful. esp32 single channel with sx1278 module and neo6m gps good range I achieved I guess it is cost effective to start with.

[@CETech4u]

Thanks! Do consider subscribing for more content like this!

[@shivamgautam1619]

Hii ..i want to connect becans directly to gateway...in between i don't want to connect tracker....how we can do ..

[@crazyfriends5507]

Where can we visualise the data we get from the gps tracker? I mean the location of the tracker?

[@junaid_qadir]

Very very nice explanation.

[@martinmchugh1924]

Great video. That gps tracker at the end was flat out sending messages, would that not easily breach the data limits that are supposed to exist on TTN?

[@TheThingsNetworkCommunity]

Awesome video!

[@CETech4u]

Thanks a lot! Up for a collab sometime?

[@yojithkr17]

What's the practical range?

[@jaydipmn]

How do I set off an external alarm if the red button gets depressed ?

[@charlyburn1868]

I remember to try this GPS tracker, but it was sending like a LoRa message each 10 seconds, and 20 minutes later battery was out. Never took time to check how to reduce the spam to make it usable.

[@CETech4u]

It's a bit lengthy process to code the LG92

[@benjaminodriscoll6605]

Great video - thanks!

[@dannytaipe6362]

Please could you explain if some reselection or handover process is supported (as mobile nerwork does) when a sensor goes from one LoRa GW coverage to another LoRa GW coverage. Thanks in advance

[@chrissywebb]

Thank you.. Informative :)

[@jesustellado7734]

For what is the red button of the tracker?

[@aaron-channel]

May I ask the signal range for the LGT-92 to the gateway? Do you think it's suitable to use for drone tracking in case of drone crashing in a remote area without any internet or GSM?

[@arnoudkooi]

Really helpful. thank you!

[@MinhNguyen-jt3ff]

I dont know how to solve this problem when i build your code on arduino, can you help me? "Global variables use 2253 bytes (110%) of dynamic memory, leaving -205 bytes for local variables. Maximum is 2048 bytes. Not enough memory."

[@valbuz]

Hi i have some trouble to get correct payloads formatted. i try your payload and fill it in. at the end, some information are correct and other not. so i dond't know if the payload formatter working correct. here is a the payload: "decoded_payload": { "ALARM_status": false, "BatV": 0.112, "FW": 151, "LON": "OFF", "Latitude": 0, "Longitude": 0.004051, "MD": "Disable", "Pitch": 0, "Roll": 240.64 i think FW,BatV are not correct, also long/lat do you have me a hint? thanks

[@UBsLab]

Wow, I had been looking for a suitable GPS tracker for a weather balloon. Would this be feasible for that?

[@CETech4u]

It would be, although I didn't have great experiences with the LGT92

[@FloRian-vb1lt]

CETech why?

[@pinoyautomotogpsmaster220]

Amazing tutorial content bro

[@CETech4u]

Glad you liked it, consider subscribing for more!

[@muhammadalifjamaludin1168]

hi, i am using the same lora shield as you but im getting an error after uploading. in my serial monitor says failure and points to radio.c:702 which reflects back to the lmic_pinmaps. could it be that my lora shield is broken?

[@btkling]

I have a Bobcat Helium gateway. Do I need to register it on TTN before I can use the dragino tracker?

[@CETech4u]

Why do you want to register it with the TTN? Its a helium gateway. E-mail us in case you want detailed help.

[@gyangbard]

The payload format is not converting mine, any help? Hint: I used a single channel dragino gateway

[@pema4366]

Hi sir, thank you for the help, I am able to read the data on the serial monitor after a few lines changed on lmic library. I can't seem to read the data on TTN, can you please help me with this issue?

[@SupriantoHutapea]

you can update your library with mcci library

[@sallu21m]

Can LoRA based GPS tracking system without use of internet or GSM signal be built for multiple users where in all users are aware of everyone else location on a digital map in real time???

[@CETech4u]

Yes, that is where LoRa comes into play!

[@sallu21m]

@@CETech4u sure... Could u please share your contact number... Need to discuss few issues... Tha KS

[@CETech4u]

Our email ID is in the video discription!

[@junaid_qadir]

Hi can you please assist me how to connect Dragino LPS8 gateway to wifi router???

[@CETech4u]

You can email us!

[@junaid_qadir]

@@CETech4u Thank you sir I succeeded in the gateway connection. Can you please provide me your email ID? My question is why the green light in the gateway does not blink? The payload received successfully but the gateway green light does not blink.

[@thierryspinneweber9180]

What's this diction. Did you learn to separate words ? Unfortunatly there is no information about reference of boards.

[@pema4366]

when i am trying to upload the arduino program, it is showing error lmic.h no such file directory

[@pema4366]

how can i compile it over the wifi, ?? i am having trouble with compiling.

[@pema4366]

Do i need to hv usb connected to my computer in order to upload and compile the program on arduino??

[@CETech4u]

Yes, and install the lmic library

[@pema4366]

@@CETech4u thank you , now i am having an error unable to connect : retrying , do I need to upload the code with USD connected to my laptop?.

[@CETech4u]

Yes

[@Whologin]

how do i update this things firmware? i found this link www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/ . but where do i go from here?

[@CETech4u]

Download the binary file from there. I am going to do a video on that soon though in order to make it a helium light gateway!

[@Whologin]

@@CETech4u this one? www.dragino.com/downloads/index.php?dir=LoRa_Gateway/LPS8/Firmware/Release/lgw--build-v5.4.1618196981-20210412-1111/

[@CETech4u]

Yes

[@arvindazad]

You are charging too much for this on your website.

[@inspactio5037]

hey, Please your mail , i have send a mail to you regarding lora wan and lora

[@MinhNguyen-jt3ff]

I dont know how to solve this problem when i build your code on arduino, can you help me? "Global variables use 2253 bytes (110%) of dynamic memory, leaving -205 bytes for local variables. Maximum is 2048 bytes. Not enough memory."

[@MinhNguyen-jt3ff]

I dont know how to solve this problem when i build your code on arduino, can you help me? "Global variables use 2253 bytes (110%) of dynamic memory, leaving -205 bytes for local variables. Maximum is 2048 bytes. Not enough memory."

[@MinhNguyen-jt3ff]

I dont know how to solve this problem when i build your code on arduino, can you help me? "Global variables use 2253 bytes (110%) of dynamic memory, leaving -205 bytes for local variables. Maximum is 2048 bytes. Not enough memory."

[@MinhNguyen-jt3ff]

I dont know how to solve this problem when i build your code on arduino, can you help me? "Global variables use 2253 bytes (110%) of dynamic memory, leaving -205 bytes for local variables. Maximum is 2048 bytes. Not enough memory."