Fantastic video. Thank you. My Losi eight is on the way and I was a bit apprehensive about installing the back plate. After watching your tutorial I’m ready. Subscribed.
@samueldeschamps88955 жыл бұрын
Great video ! I was waiting for this ! 😁
@316RC5 жыл бұрын
Sam deschamps Should have part 2 up in a couple days.
@CoyoteDeadShot Жыл бұрын
So they don’t have those engine mounts anymore. They were discontinued and out of stock everywhere. Can this be done with other engine mounts?
@WackyMonkeyNuts5 жыл бұрын
Nice turorial, thanks for this info!
@hizzleman41115 жыл бұрын
Nice video, just what I want to do to my Losi 1/8 8ight RTR. Does this engine mount and back plate work for the 8ight RTR 2.0?
@316RC5 жыл бұрын
I'm not familiar with the 2.0 What engine does it have? The parts in my video will work only with the Dynamite .28 or .21 engines.
@camaroboi135 жыл бұрын
@@316RC The 2.0 Mounts are the same TLR 241017 if memory serves correctly. They are already lower because the 2.0 comes bump box ready. FYI, the Losi engine mounts are 25-30 dollars online, but there are several listings on ebay selling stock 4.0 mounts for 5-7 dollars plus shipping. These are the same part numbers so you can save yourself a few bucks here.
@RcPilotBrown5 жыл бұрын
Just did this. Thank you for the video! The rtr 8ight T is the 2.0 version (purple and yellow body) and requires TLR241017 Losi 8ight 4.0 engine mounts for a starter box , even the Losi 8ight starter box.
@wolfgangwiesinger4975 жыл бұрын
Nice video. very good
@jriley19745 жыл бұрын
My cord is stuck in its most retracted position. I was breaking in the engine when I let it run out of fuel, and now the pullcord won't extend from its coiled position. How do I fix this?
@316RC5 жыл бұрын
Pigletsandbacon did you set the piston @ TDC when the engine stopped? Can you turn over engine by moving the flywheel? If not the engine is probably froze up because the cylinder is tapered. Heat up engine with a heat gun to like 180 F. That should free it up.
@jriley19745 жыл бұрын
@@316RC thx so much for the tip, totally loosened it up. Btw, does the engine have a tendency to finish TDC (when running it out of fuel) as that's where it has most resistance? Is running out of fuel that harmful when breaking in because it leans out before it shuts off?
@316RC5 жыл бұрын
Pigletsandbacon yes, more likely than not. Best to set your engine @ BDC then take a sharpie and make a mark on ur flywheel as a reference. When u shut down just move the flywheel to your mark reference and you know your @ BDC. No it really don’t hurt to run the fuel out lean.
@johnf30105 жыл бұрын
What part numbers do you have for the backplate and engine mounts. I want to do the same thing to my rtr!
@316RC5 жыл бұрын
JOHN F You will need two items. TLR 241017 engine mount set from Team Losi and Dynamite DYNE1506 pull start eliminator pack plate from Horizon Hobbies.
@FORD150-5.45 жыл бұрын
I order losi 8 .21 I have the starter box can work in this buggy whitout take of the pull start?
@316RC5 жыл бұрын
No. You must remove the pull start if you want to use a starter box. Can’t have both.
@d3et1roi3t4 жыл бұрын
I just got my 8 t rtr. is there a antenna in the box? mine dont have one
@316RC4 жыл бұрын
There should have been a small inch and a half one on the receiver box. Don't remember if it came that way or had to install it. I think it came already installed