Slowing Down my Rotary Welding Table

  Рет қаралды 1,731

Lucid Autowerks

Lucid Autowerks

Күн бұрын

VEVOR Weld Positioner - s.vevor.com/bf... (may have updated motor)
40rpm Motor - amzn.to/3JjNp6Z
Micro Torch - amzn.to/4cR5LK3
Soldering Station - amzn.to/4aOJzhO
Replacement Crimper Dies - amzn.to/3PVMhdy
SuperClean - amzn.to/4d5TnGi (also available locally at Advance Auto, Ace Hardware, Lowe's, NAPA, O'Rilley, Walmart and more!)
Check out - lucidautowerks...
Questions?
email: LucidAutowerks@gmail.com
Mailing address:
PO BOX 840146
St Augustine, FL 32080

Пікірлер: 31
@AtlanticBuilt
@AtlanticBuilt 29 күн бұрын
Awesome video! I bought the same one, and it is wayyy too fast. This was a great idea, and well explained thank you! can wait to try the swap.
@LucidAutowerks
@LucidAutowerks 29 күн бұрын
I use it every week and it’s been great since I swapped the motor!
@AtlanticBuilt
@AtlanticBuilt 29 күн бұрын
​@@LucidAutowerks awesome to hear! Very glad I found your channel. Subbed! 🤙
@melgross
@melgross 6 ай бұрын
These small ones are rated up to 80 amps. That’s it! I’ve got a similar one, not from Vevor. I think it cost me, around 18 months ago, $325. Prices have dropped to about $263 now. I’ve gone to 120 amps and it’s been ok, but I wouldn’t go higher than that. Mine does have a reverse switch. I’m thinking of going to the next larger size.
@LucidAutowerks
@LucidAutowerks 6 ай бұрын
My Hobart 190 just has letters for the settings, but apparently I’ve been using it at 180 amps on the rotary table! Haha. I did notice that I can’t wrench the chuck closed before welding because it’ll be super tough to open the chuck back up after the weld. Other than that, I haven’t noticed any issues.
@melgross
@melgross 6 ай бұрын
@@LucidAutowerks well, other than the lug burning out. It’s a risk though.
@LucidAutowerks
@LucidAutowerks 6 ай бұрын
@@melgross it’s been great ever since I replaced the lug and the clamp.
@melgross
@melgross 6 ай бұрын
@@LucidAutowerks ok, not criticizing or anything.
@LucidAutowerks
@LucidAutowerks 6 ай бұрын
@@melgross I know. I didn’t take it as that. I agree with you. I’m sure I’m overdoing it with this little rotary table. I had wanted to build one like This Old Tony did but I just don’t have the time these days.
@henryrosado1549
@henryrosado1549 14 күн бұрын
Would you recommend even a lower rpm motor for tig welding?
@LucidAutowerks
@LucidAutowerks 13 күн бұрын
I haven't TIG welded on it yet, but I think it goes slow enough to use for that. Lower RPM wouldn't hurt though since at the higher speeds it's still faster than I'd ever use for welding. Someone mentioned that the higher speeds are for grinding but I don't use mine for that.
@lyotochamida8466
@lyotochamida8466 3 ай бұрын
The faster speeds are for grinding on the positioner
@rayp.454
@rayp.454 5 ай бұрын
Thanks for the link to the motor. I'm going to try the 20 rpm for TIG welding. I found the speed as a flaw also. What were they thinking??
@RosinEnthusiast
@RosinEnthusiast Ай бұрын
how did the 20 rpm motor work for you?
@rayp.454
@rayp.454 Ай бұрын
@@RosinEnthusiast It is way better, but honestly range would be better if was even slower.
@RosinEnthusiast
@RosinEnthusiast Ай бұрын
@@rayp.454 hell yea sweet I’ll order that one right now is it the same brand as the one linked in the video?
@RosinEnthusiast
@RosinEnthusiast Ай бұрын
@@rayp.454 I ordered the 5,10 and the 15rpm motor to test out I will post my results
@AtlanticBuilt
@AtlanticBuilt 29 күн бұрын
@@RosinEnthusiast would love to hear about this. I thought I just couldn't hack the positioner thing. turns out it IS way too fast for everyone lol.
@danman9017
@danman9017 7 ай бұрын
good job
@bobreichel
@bobreichel 6 ай бұрын
I bought this unit and did not get the clip and carbon brush to allow the unit to give the ability to use the turntable for Welding. I've contacted vevor about this and am getting the runaround. They said it's a consumable they drop $60 off, and I then needed to find the brush and clip. I said no way either send the part or give me a return label and a full refund. I wouldn't have any idea where to buy the part and I'm assuming by there reply they don't offer replacement parts rendering it worthless in time. Bad business practice.
@LucidAutowerks
@LucidAutowerks 6 ай бұрын
Yeah that brush isn’t a part that seems like it would be easy to source. I’ve heard that their customer service isn’t very good. I guess that’s the cost of buying cheap tools from an internet based company. You might be able to check on McMaster.com for something that would work.
Rotary Welding Positioner Review and Test
15:30
Ames Management
Рет қаралды 3,6 М.
Is This Cheap Plasma Cutter Any Good?
10:10
Lucid Autowerks
Рет қаралды 4,3 М.
The IMPOSSIBLE Puzzle..
00:55
Stokes Twins
Рет қаралды 161 МЛН
This Game Is Wild...
00:19
MrBeast
Рет қаралды 138 МЛН
When u fight over the armrest
00:41
Adam W
Рет қаралды 30 МЛН
Adam Savage's One Day Builds: Portable Soldering Station Rebuild!
53:21
Adam Savage’s Tested
Рет қаралды 354 М.
Cutting DRO glass scales is easier than you think.
11:25
Mike's Workshop Adventures
Рет қаралды 7 М.
Rotary welding table - Build
15:15
Mateusz Doniec
Рет қаралды 368 М.
Stick  Aluminum Together Without a Welder.
12:32
AM Custom fab
Рет қаралды 1,2 МЛН
DIY Metal 3D Printing - Success
38:35
Metal Matters
Рет қаралды 252 М.
Is It Worth It?   TITANIUM WELDING TABLE I HARBOR FREIGHT
21:51
Barr Run Forge
Рет қаралды 19 М.
The IMPOSSIBLE Puzzle..
00:55
Stokes Twins
Рет қаралды 161 МЛН