Forward Reverse Control of Electric Motor with Relays

[@johnx9318]

Thank you for breaking it down. That has been driving me nuts trying to figure this out!

[@stuffoflardohfortheloveof]

Brill. Thanks 👍 My only confusion (small point) was that I paused the vid at 5:30 to study the diagram and because you had ALREADY pencilled in the switch position, the diagram didn’t make sense as the motor would NOT have turned.....it was only afterwards when you ran through the diagram and RUBBED out and amended the switch position that it all made complete sense......thanks again

[@ecospider5]

He never showed the bottom connection fully erased which is how he should have started.

[@twadam5218]

Thank you! I just used this schematic on a project of mine. Works great!

[@jhellvie]

This is best when need to do something.. Explain the components how it works and how to use it... Its very helpful to those newbies like me... Atleast can share to those people who have no experience But willing to learn...thanks man

[@electromagnet3176]

Your experiments is always very nice because your explain is very good.

[@jasonk8936]

Your video couldn't be any clearer. Good job!

[@ludicscience]

Thanks!

[@standolfo]

Hello is it possible to have a Forward Reverse automatic controller, I mean a controller that does Forward and reverse automatically every 2 seconds without need of switching manually

[@mousumisarkar721]

Wonderful video.Keep exploring new ideas.

[@hadireg]

This can be modified with the coils wired in parallel and NO1 & NC2 to Positive , NO2 & NC1 to Negative. so one command from an arduino can toggle the motor direction. Thnx 👍

[@MOHAMADGHOUL81]

This concept of motor control by relays applies the dish satellite positioner. I met the idea on STRONG SRT series of analog satellite receiver. Thank you for sharing. Best regards MOHAMAD GHOUL

[@Yorwos1]

Thank you very much . I've been looking for this kind of set up for a long time

[@sonusanat]

For the relay like relay module the diode and transistor and resistor not required?

[@maxprophet2401]

Good subject, easy and very usable! Thanks LS

[@ludicscience]

😊

[@TheSocialPraxis]

I have an actuator I want to stay down while my car moving, however when I press on brakes I want the actuator to open/extend and when I remove.my foot from the brakes I want it to close again. Is there a way to do this with relays? Please and thank you.

[@dahterofawhtechik]

Can the switch be automated/replaced by a program? A timer?

[@johnmoore3859]

Excellent video. Easily understood. Well presented. Thank you so much for taking the time to make the video and for sharing sharing the knowledge.

[@pg9112471]

How do you add limit switches.

[@thefreedom9973]

can i use relay 4pin? for this project?

[@pachuco8366]

Waaoooo maestro , no sabía que tenía un canal en inglés ,lo felicito 👍👍👍😁🙏🙏🙏🙏🙏🙏

[@randomelvis3359]

A DC battery drill project...i want to use a remote control to activate forward and reverse is this possible?

[@two_number_nines]

A double throw switch could do the same operation, but cheaper, more reliable, faster and more energy efficient.

[@axpanos]

For small DC motors like the one used in the video what you are saying is totally correct, but for big three phase motors that are used in industrial applications, having a switch connect directly to such a high current circuit could be extremely dangerous, the purpose of the video is to demonstrate the use of relays for controlling big motors

[@VanDerLaars]

The video is for educational porposes.

[@MegaFaisal123]

I vant understand where u connect the medal of botan and left side relay do we need 2 battery

[@neerajkumaraj2703]

This is the best video ever, i found on this topic thank you so much for teaching me , I appreciate it

[@anikettripathi7991]

Great. Possibility of many solutions are helpfull for everyone according to their needs. possibility is freedom.

[@narabahadurgurung1297]

Awesome presentation 👍👍

[@vinayurankar4750]

Can this be used for drill machine? Thank you.

[@paulcomerford556]

I enjoyed your video and it got me thinking of a project I would like to do, but need a little help on what I need to accomplish it? I am trying to modify a winch from a hand held remote to a wireless remote. I have a two channel wireless receiver(Two positives and two negatives) but I am a little confused on what type of relay I need to be able to run and reverse the direction of the winch. Do I need: SPDT, DPDT? Do I need a 5 pin, 6 pin, or 8 pin relay? I plan on running it directly from an outlet so I know I the relay will have to be rated for 110 volts. If anyone can help me understand what I need and how to do it, I would be very greatful.

[@alchemy1]

How to do this with a potentiameter so the speed of the motor can also be controlled?

[@antoniotalone6098]

Se metto il pulsante su neutro il motore continua a girare?

[@TheCerberusInferno]

Thanks a lot my friend , i understand this scheme now perfectly

[@TanvirKabir0461]

To Forward and Reverse a DC motor no need any circuit really, you can use a 3 position 6 pin slide switch. First 2 pins connect power,(No. 1+ and No.2-) then the 2 pins in the middle connect the 2 phase of the motor, and the last 2 pins(No.5 and No.6) connect the power from first 2 pins reversely by a small wire, 1+ connect to No.6 and No.2- connect to No.5. and done...

[@rc3d490]

yes,you can make it, but only for small motors

[@SHADOW-bg4mm]

i like a design im buying, it is a Wireless Remote Switch 12V Universal 2 Channel RF Remote Control but need more max load when it comes to amps, is it possible to change the 2 relays inside and put a higher rated relay like 40a without any problems with the receiver, remote switch itself? it is max load rated at 10amps or less originally

[@salmobulahao7526]

What will happend if you connect the relay coil in series? Does this work?

[@melplishka5978]

Isn’t it safer for the switch to switch the grounds rather having the load through the switch ?

[@moathnaji6202]

Can you make reverse current polarity protection by more than one methods?

[@GASHIK-op2wi]

Sir how it can be done using a single battery..?

[@moldprintsrl]

Can this system be wired to the same power source? I need to wire everything at a 12v battery

[@Steven-e7c]

Love this! Anyway to add a controller like an actuator can?

[@jaffasoft8976]

How can i twist something 90 degrees on and 90 degrees off?

[@Flyingwigs]

so it would be really easy to use momentary buttons and add micro switches to limit travel with this circuit, thanks!!

[@aakashroy2501]

Awesome video as always but why less uploads and projects

[@ludicscience]

Less?

[@aakashroy2501]

@@ludicscience never mind your videos re amazing

[@Tolderian]

Now add the short-circuit brake mechanism

[@hectorj9269]

Hi can you help me I got a power steps for my Chevy pick up how they wiring with my door open and close

[@123leooel1]

peut-on faire la même chose avec deux transistors?

[@larrybari1389]

What is the name of the switch or tell me if we can use any switch.

[@ecospider5]

5 pin relay (you need to get the voltage right) 5-Pin 12V Bosch Style Waterproof Relay Kit [Harness Socket] www.amazon.com/dp/B01MTQNJKM/ref=cm_sw_r_cp_api_i_x9moFb7N7AT5H

[@timryan6121]

Could you identify the pin numbers in your diagram. My relay has the following numbers 87, 87a ,30, 86 & 85

[@rc3d490]

test it with any multimeter for identify the NO NC and coils pins

[@bravosierra1856]

Thank you for this great info. I was able to use my defective servo using your circuit. Great job.

[@adamlevi-rodgers9174]

Really clear and helpful instruction thank you

[@miloshthegreat4938]

Nice video tutorial. Can You made this with Day/Night sensor (Motor Forward/reverse) ? On Day in one direction, on Night other direction. Without switch. Thanks in advance

[@hectorj9269]

Hi can you help me how i wire my power steps on my 2010 chevy silverado

[@moathnaji6202]

Can you tell main difference between a DC motor, a Servo Motor, and a Stepper Motor with advantages and disadvantages.?

[@arduinoexplorer5437]

Check this site . www.elprocus.com/difference-dc-motor-servo-motor-stepper-motor/ Note that the pictures are not fully correct except stepper motor..

[@albertolostaunau9567]

This tutorial is GREAT!! thank you so much!

[@ludicscience]

Glad you like it

[@rajeshkumarrajesh2887]

Thank you so much it helped me a lot.

[@Bytemusic]

love your video. really useful. Can you help how can I add 2 Limit Switch to change the polarity?

[@ecospider5]

When the diagram is first shown the coil on the left was drawn activated at the bottom but not activated at the top. Which was wrong and confusing because you never showed neither coil connected. Which would have been drawn with the line at the bottom erased. So the drawing should have started with no line at the bottom showing no coil activated and the top as it was with both in the negative position. Then you draw the line at the bottom to the left and the video would be correct where you switch the left relay to positive.

[@mrz6320]

how to speed up the motor with that relay?

[@ecospider5]

That type of motor is constant speed based on battery voltage. Normally you would not use a relay to change speed but technically you could have 2 12v batteries that are switched from parallel (12v) to series (24v) which would double the speed.

[@electricbrain1736]

I want to apply to semi automatic crossover winding machine

[@technicalfriends7327]

Excellent described . Thank you sir

[@andrewg8364]

Amazing video; thank you so much!

[@koum4564]

can you show how to used 12v polarity on timer I like to build my green house and use DC motor to open and close let say open at 7:00 a.m and close 6:00 p.m

[@omarijaphet9593]

Well explained

[@cobraAH1]

please add limit switch for this connection

[@JasonSipe16]

Excellent explanation. Thank you so much!

[@Dadolaurenovic]

Excellent mate,thanks for that.

[@surinderverma5784]

Sir thats very interesting . Plz make a wireless transmitter using 433mhz module

[@MrBuinickas]

Great work thank you

[@tjahyasetyabudi609]

sceme for Dc , can this for Ac Mr, thank

[@briantw7096]

Great Video as always!! Thanks Brother! Keep them coming

[@ludicscience]

Thanks!

[@631HOTSHOT]

Now you need to put a potentiometer in there So the motor stops when it hits a specific range

[@llablancheHermineBZH]

merci je vien de trouve grace a vous le schemas electrique pour l'automatisation de ma porte de mon poulailler avec LDR et fin de course

[@ziadfawzi]

Thank you.

[@Berghiker]

Can you make a circuit that reverses the polarity every 0.5 seconds?

[@user-zt2wc3uh1l]

You can do it with this.

[@Berghiker]

@@user-zt2wc3uh1l I am talking about an oscillator circuit that does it automatically.

[@user-zt2wc3uh1l]

@@Berghiker , from what I gather, it can do that. set 07 to 01.

[@lez7875]

saudações do Brasil a todos. muito bem explicado. humm... relês podem até ser usados como portas lógicas. muito bom. sucesso.

[@shahzadnaeem861]

Why cant we use the same power source for both operating motor and for relay operating !!!

[@TallPaul7771]

Could you make a similar video showing how to reverse a PWM motor? Thanks

[@karenjoygregorio8737]

You can reverse pwm servor motor and repossition using a pulse width modulator circuit. And pwm motor like the cpu fan only itd speed can be controlled.

[@Berghiker]

I'm looking for a circuit that does this automatically, not using a hand to flip the switch.

[@keithcitizen4855]

I made this for a piano nicholodian to replace a rotating wafer switch

[@wiam89-v6e]

Thank you so much, very useful viedo

[@tahirkamboh147]

Thanks

[@enochkandiah6445]

great vid.

[@allelectricandelectronicma8298]

Yes this is perfect connection

[@tjmchanel8049]

Using limit switch pliiis!

[@1974skin]

Hello sir Is possible to make this with only one push button!?

[@incxxxx]

simple and nice!

[@ludicscience]

😊

[@motsadesire9911]

@@ludicscience thanks. Pls do the one for door glass

[@Elgringo95]

So thanks

[@electricbrain1736]

The switch should be ON ON the switch

[@moviecell1335]

Very usefull sir, thanku verymuch

[@nikiamz6501]

Very useful thank you! :)

[@ludicscience]

✌

[@m.samaha4708]

There are motors with many wires come out from it.

[@nishukumar5911]

Very good

[@electricbrain1736]

In my circuit I don't want the motor to stop at all

[@yns7430]

Superb

[@moathnaji6202]

How To Make A DIY Electric Lighter

[@igrewold]

Thanks :)

[@telabela007]

Sandaar 🙏🙏

[@eduphymath6581]

Lot of tnx sir very usfl

[@dinushkasampath4725]

Good job 🖐️✝️💙🔥🇱🇰

[@stephenhutton7849]

i just simply used a 6 terminal switch

[@michaeltucker8645]

Right way easier for manual control but you can use this set up with a cheap toy grade rc receiver and controller to remotely control much larger motors than the super cheap toy grade circuits could handle. That's how I am building a large rover from a small gokart frame 6 12v 14am wheelchair motors combined weight limitations around 2150lbs with a mover deck to remotely cut my grass and also to use some salvaged windshield wiper motors I made into linear actuators welding some all thread to them to build dump still bucket on it and 2 arms to pick up branches and other debris from out of it's way. I have a limb trimmer I'm thinking of using same set up to trim up trees from it as well. I sit inside and use it I just used a busted drone fpv camera and 4.3in fpv monitor. Steers like a tank does. Need 3 more busted drones for 360 vision lpl

[@melplishka5978]

Sry I miss read the diagram lol. Your only switching the relays not the load to the motor. Ya I’m stupid lol.

[@jpscafe7648]

Boa! 👏👍🙏 Show de⚽ 🇧🇷 Obrigado. Bem explicado boa demostração. Ok like e inscrição.😁