Luxpower SNA 5k PV+AC Take Loads simultaneously

[@msumzam]

Take you so much, I managed to do (as a customer), what I've been begging my installer to come and do (set up the PV/AC to take the load together.

[@andregabrielse2605]

It would be nice if companies monitored their social media and replied to customers / potential customers

[@Namib-AKA]

Good day thank you for the well presented information, just one question and will it work with SVolt battery

[@everts50]

Would it be possible to connect a tse power 4.8kw lifepo4 battery to the luxpower inverter to use bms

[@hermanheyns5308]

Can you set the inverter to take the load together but the grid to take preference. Therefore at night using the grid and only if the grid is not available at night use the battery (we dont want to use the battery at night unless there is no other option so only when the grid is offline - want to keep the battery for emergencies)

[@toddmunemo4576]

Did you get this right? I need to implement the same settings but can't seem to get it right.

[@dumisanid8733]

Bought this inverter thanks to this video. Can I connect my kitchen plugs with a 2KW kettle to essentials to balance AC loads with PV during the day?

[@francoisraath3593]

We have a situation when this Luxpower inverter is connected to Deye batteries, when fully charged, and Grid falls away the inverter does not take over. It goes dead. When battery is reset all boots upand takes the load. With any other type of battery it does not happen. No coms cable between inverter and battery. No solar. Can Luxpower follow this up as we have three exact cases currently.

[@bernardpahla1433]

If say you are using the inverter as backup system that is no Solar Panels. If say the battery is fully charged will the inverter continue to draw power from the GRID and only draw power from the battery if the GRID goes off.

[@takudzwanyamakanga8001]

Anyone to answer.. I have a leupower inverter and a elf bulb lithium battery.. When the installer installed he told me the communication cable doesn't matter and it is not necessary he did not put it on.. Everything is working but the inverter doesn't show battery % and on battery type it shows lead acid.. Can i change these options on the inverter without the communication..cabble will there be any problem?

[@lawrenceharris1819]

Hmmm. We bought a Luxpower controller + 2x 3kWh batteries. As I have reported elsewhere, without success, the controller is fond of sleeping and takes a long time to wake up, so the efficiency of the system is low and the 'saving' can never match the original cost. My original calculations were based on believing the ads which implied that switching was near instantaneous. Not so. I have measured the time between putting a load (eg 2kW kettle) on and when the system kicks in. It varies depending on whether the controller is still awake from a previous supply - or not. It can easily take up to a minute or more before anything happens. Of course, when the load is no longer required, it exports the energy to the grid (!!) for as long as it takes to switch off. FWIW I did get a response from 'an engineer' who looked at my system remotely, made one or two adjustments, and was never heard from again. 😞

[@LUXPOWERTEK]

We apologize for the inconvenience you've experienced. Could you kindly provide your SN (Serial Number)? Our technical support team will review your system status and investigate the cause of the prolonged sleep mode.

[@francoisvanschalkwyk9858]

How much watt does a 5 KW inverter draw from a fully loaded (x2) 5kw batteries with no load on the house at night with no grid power coming in ???

[@hendrikschutte9126]

How do I connect a lux power 5kw inverter with a shoto 5.12kw battery

[@dawoodadam2926]

Good day Can you please make a video on how set your charge and discharge setting on an back up system using a hubble am5 battery

[@drhatemhadi1]

Can this inverter programmed such that if generator opereted but not sufficient the request load then battery feed above to complete the request.

[@francoisvanschalkwyk9858]

I have to choose between growatt and lux.. with inverter is more energy efficient?

[@SikelelaVunguvungu]

Thank you for the information. However, I have a challenge of not being able to take my laptop to sight to do these types of settings. I would really appreciate it if you guys did a video where we the installers can learn to set up these programs on the inverter rather than using an app. With your competitors, we are able to do the settings online. For example Growatt, Deye and Sun-Sync we can do the settings on the inverter then the client is the one that can monitor and make changes according to their preferences and understanding. With Luxpower it seems as of everything is done remotely which is tedious for some of us.

[@LUXPOWERTEK]

Hi Sir, thank you for your feedback and suggestions. With Luxpower, settings can also be adjusted on the LCD screen. We have forwarded your suggestion to our tech support department, and they may organize training on how to use the LCD screen for settings.

[@zugdien]

Hi Andy how do a person get in touch with you?? I am installer and need assistance sometimes.

[@rynoopperman5010]

Thanks for your video but honestly this is pretty useless info... How did you connect the AC cables to achieve this?

[@opfier]

Hey! Can I use my own lifepo4 battery? without can connection?

[@vhutshilomoses7919]

Hi i have done all the necessary settings but my SNA5000 does not want to charge using AC and always using battery even when i have set a SOC. please assist

[@jtindisa]

I want my Luxpower to charge the battery to 100% and then continue using the grid only. However, whenever it gets to between 90% and 100% it starts using the battery even when the grid power is working.

[@LUXPOWERTEK]

Hi Sir, thanks for your reaching out. You can set the working mode to be AC charge with the time during 00:00~23:59.

[@zparkergeco]

Hi there, I have a SNA5000, will the inverter trip the CONLOG meter if its used in hydrid mode

[@user-wd9hr4se6j]

Hi can you help as soon as I connect the parralel cable I get an error 28 with a sad face

[@LUXPOWERTEK]

Hi Sir, Sorry for the bad experience, could you please share your SN with us?

[@user-wd9hr4se6j]

@@LUXPOWERTEK we had a bad experience with the client but it jas been sent back to the supplier....there was/is no one that could help with error codes 28 and 29. In the end I brought 2 inverters out of my pocket to save face.

[@darrencupido6131]

Is it possible to just run pv and grid withou battery’s

[@gerhardwilkens847]

Can you run a hoselect lithium battery with this inverter

[@johnmitchell988]

Can the SNA 5kW Battery+AC Take Loads simultaneously

[@hannesjohannes2281]

Hi can u make a test for us with a welder. Then i will buy it.

[@rynhardvil2231]

what is the model number for this unit?

[@keithnortje1720]

Sna5000wmv

[@stupidusername38]

I've only seen it mentioned that these work with the Pylontech us2000 batteries. Are the us3000 batteries also compatible?