M113K ENGINE BUILD, from Darton sleeves to headstuds and CAM INSTALL!!!

[@NudaMan]

This makes me more happy about buying a CLS500 or E500 as my first mercedes & first car to mod lol, soon VRP,RaceiQ & MSC are going to take my money 😂

[@anthonycastro5402]

The mad scientists doing their best work on a M113K😍😍

[@ModernMastersAuto]

Love it!

[@haroldcain2666]

Then I wish you guys would do an M112V6Build From the bottom up For a 2005 Mercedes Benz C240 rear wheel drive2.6 l V6

[@ModernMastersAuto]

Soon

[@chrisford1222]

Ahh the m113k my favourite engine imoa the best Mercedes ever made 🇬🇧 Mercedes diagnostic tech approved

[@ModernMastersAuto]

Yesss!!!

[@JMSpeedshop]

Are on all m113k intake and exhaust valve springs the same? So intake and exhaust valve springs are innerchanceable? On your springs the are all red and white paint. Ony heads some have only white paint. But the are not only in the exhuast or intake . I think on my springs some red paint is washed of. So are the all the same intake and exhaust. Part numbers from oem is same. Waht is your opinion

[@tonychirillo1095]

Awesome Love the m113k content. Can’t wait to see what kind of power the engine produces. It’s good to see Phill with VRP ! Oh, and Rusty is looking GOOD ! lol

[@ModernMastersAuto]

We love these engines!

[@Fernandonelu]

Awesome video guys

[@ModernMastersAuto]

Thank you!

[@glennjames9152]

...oh geez, not sure why I was pointed to this video. But, I now see why. First, I must vouch for these cams. In my car, I had custom grinds, and cams from another M113k supplier, these cams by far make the most power... I did some testing with our Faro and CMM as I wanted the overlap values.. For being a supercharger cam, these cams allow for the cylinder to retain pressure. This is a plus for boosted engines because you don't need a higher static compression ratio to offset the overlap that the other cams had. Installed these cams and gained a ton of whp. Buy these cams! I NEVER plug a product unless it's legit. These cams are for real in the M113 world. As far as the "does it exist," Phantom, it's THE quickest (1320) E55, or Mercedes, in the world! It now sits in the garage next to the fastest LT4 in the world! I'm waiting for one of these VRP Whipple cars to come get some!

[@ModernMastersAuto]

I need to come visit haha

[@glennjames9152]

@ModernMastersAuto Come see it; just confirm I'm there this time...

[@ModernMastersAuto]

@glennjames9152 sounds good I'll hit you up!

[@robertlambert5299]

Any vids of it running down the track?

[@Leonardo555ZZZZ]

3,2,1...3 Valves , 2 spark plugs , 1 cam = reliable M113k power.

[@ModernMastersAuto]

💪💪💪

[@Don_jon333]

I love my m113k. Can’t wait to build mine

[@Hursh1]

Would you guys know a ballpark price for a timing chain job and cams? Im only like 2hrs from your shop. Great video 🔥

[@ModernMastersAuto]

Email us for sure!

[@ctravis595]

Technically an n/a 113 without the triple bracing in the V of the block and 6 bolt mains on caps 1 and 5. Arp recommends 90ft lbs for those studs on alum heads/block btw. Apparently only supposed to use arp lube on one side of the stud washer, although I also lube both sides

[@W210Garage]

Is it difficult to install bearing bridge? Should i consider any trick? Also when i put the rocker arm in it's place, should all the hydraulic lifters move with the hand freely when the bolts aren't tightened? I just installed AMG Cams in my M113 and now i should install bearing bridges.

[@ModernMastersAuto]

Slow and steady

[@josephlind4723]

Ai recommended this video lol n I’m not disappointed at all 👌

[@irageatf0rt]

Is it possible to install the cams with the motor still in? I have a e55 amg with a bad intake came

[@ModernMastersAuto]

Yes

[@irageatf0rt]

@ Should I get rocker assembly as well. Not sure on the extent of damage from a bad cam

[@ModernMastersAuto]

@irageatf0rt probably

[@33adrenaline]

i have the VRP street cams in my E55 and LTH. it is a monster well baby monster lol.. i need new injectors and a bettter tune im detuned bascially for now until money arrives fo rnew parts lol. but these guys are the best

[@ModernMastersAuto]

Let's gooooo 🔥🔥🔥🔥

[@fredrikmyrsta2616]

Is the rocker arms original or costom?

[@ModernMastersAuto]

Custom

[@fredrikmyrsta2616]

@@ModernMastersAuto where did you get them or you did it yourself?

[@robertlambert5299]

Any link to the 8 sec E55. Would like to see more about it.

[@Don_jon333]

There’s an sl55 running that. Google is your friend

[@benjamingoldsmithjr8540]

How much this job go for 🤔 ?!?

[@ModernMastersAuto]

Big money build 20k or more.

[@hEXordo]

Aside from my ml63 I wana do cams for my 208 55, could i use cls500 cams for the vrp cams service?

[@ModernMastersAuto]

Has to be 55 cams as na cams aren't the same.

[@hEXordo]

Can i send my ml63 to you guys for pistons and upgrade turbo and downpipes?😅

[@ModernMastersAuto]

Yes always

[@hEXordo]

What would something like that cost if i supplied the weistec parts

[@ModernMastersAuto]

@@hEXordo email me

[@rlscustoms]

Ah yes the German LS motor I love it!

[@ModernMastersAuto]

Yes!

[@rlscustoms]

@@ModernMastersAuto tuned a bunch of these they’re awesome but have never dived into the motor like this yet but when I do you can bet those cams are going in it!

[@kidvybez]

woah im still watching but how much does this cost

[@ModernMastersAuto]

All of it lol

[@kidvybez]

@@ModernMastersAuto more so engine build lol i have a e55

[@vicboykin8576]

Master Mechanics. We need you and Phill to get some badging.

[@boytoycliqueinc]

Yee yee 🤙🏻

[@Diamondo25]

you should treat rusty a bit better man. he calmy explained a lot and you come in and disturb the piece with something 'fun' :/

[@ModernMastersAuto]

I'm a wrecking ball, but I love my guy Eugine!

[@sirlayo]

😂 literally

[@Sikici_Usta]

22:20 Beep! xD

[@ModernMastersAuto]

Lol