VCR vs. Reel to Reel for Recording Music | Can you tell the difference?

[@MadeOnTape]

Hey y'all! I'm first and foremost a musician, but I try to present technical information as accurately as possible without over-extending my knowledge. In other words, I don't like bulls**ting. If you're interested in the technical aspects of VHS audio, this article clears up older versions of VHS vs. Hi-Fi stereo VHS (my machine): www.broadcaststore.com/pdf/model/793700/TT190%20-%204626.pdf ✌️📼🎼

[@MadeOnTape]

Hey y'all again! There has been a lot of back and forth in the comments section of this video and confusion about an older format of VHS sound and the embedded hifi audio that became standard and commonplace by the time I was a little kid. Luckily for me, my video stands correct when it comes to the spinning head utilizing audio heads as well. This excerpt comes from a forensic science article from 2006...you know, people who have to study tapes as evidence in criminal cases: "The hi-fi, or frequency-modulation (FM), audio stereo heads are located on the helical-scan drum, often 60 degrees out of phase with the video heads. The hi-fi audio is recorded during the 0.0334-second time period just prior to, but in the same tape location as, the corresponding video information. To allow differentiation of the audio and video signals and to avoid complete erasure of the audio track by the subsequent overlying video track, the signals have different azimuth angles and track widths and record at different tape depths. The video head partially erases the hi-fi audio, usually dropping its amplitude about 12 decibels (dB). The two channels of stereo audio are recorded with different FM carrier frequencies for better record and playback characteristics. Because of the recording methods, the signal-to-noise ratio, frequency response, and other specifications are always better for hi-fi than linear audio. Hi-fi audio quality is virtually the same at both SP and EP speeds; however, not all VCRs have hi-fi audio capability (Beeching 2001; IEC 1999; Trundle 1999)." www.experts.com/articles/video-and-audio-characteristics-in-vhs-overrecordings-by-bruce-e-koenig

[@MadeOnTape]

or if you wanna watch a rad video from 1984, check out this one-minute gem: kzbin.info/www/bejne/f3fCo4eKpdmUnpI

[@guessundheit6494]

Talk about shitty and unwatchable editing. But even without that, it's direct ripoff of Cassette Comeback's video, "Hi-Fi VHS - The Poor Man's Reel To Reel". Stealing content because you don't have the imagination to create your own. kzbin.info/www/bejne/oqbRnKSIZ9F3l8k

[@MadeOnTape]

@@guessundheit6494 Hi Guess! I appreciate your feedback and the time you took to watch and comment here. I love that video you posted and that content creator Cassette Comeback... ...so much that I had put a link to it in the description already. Let me know if you're ever interested in beginning to create content on your channel and I'd love to talk about imagination, originality and producing. Of course, you may have another channel that i'm not aware of! Peace, and have a beautiful day 🙏✌️

[@PedroMartinez-sp1cb]

Hi, I've got a question. What was your gain staging or process for recording into VHS? I have the same VCR as the one in your video but my signal is way to high and clips and distorts, even with the master volume at really low on DAW. I'm wondering how you got yours to sound so normal.

[@dandiehm8414]

What he forgot to mention was the COST. Not only are VCR dirt cheap (especially compared to a good reel-to-reel) but the tape cost is miniscule. And, because of the helical recording system, the VCR tape speed has no bearing on sound quality. Meaning for about $20 you can get 6-8 HOURS of recording tape. Try that with reel to reel.

[@andodigital1]

Hi. what want for 1 to 1 quality on VHS ! 1. Need PAL or NTSC This is the Best Choice with 4.43 because on NTSC recording take more tape space for audio recording and Les for Video signal Then on Pal ,Left channel is 1.3Mhz Right Channel 1.7Mhz! 2. Need VHS with Long play (LP On PAL OR on NTSC Extended Play EP or (SLP)) Because on this mode lowered video quality but again take more space for AUDIO on tape ! 3.HI-FI NICAM because minimum need on drum 2 Long play Head ,2 Standard Quality play Head ! 4.Black signal generator on VHS calling this button (SIMUL) Or ( Test signal) on BACK This generate Black video signal ,need for tracking stable simulation because VHS tracking system looking this information for synchronization ! When not synchronize tracking system non stop looking and make on recording noises clicking like scratching noises ! ON VHS Without Black Screen Generation Need give in black screen video signal from another device get same results ! 5.For best result need check some VHS Without Recording Level adjustment gives the best recordings when input 5 volts but on 0.5-0.7V results poor ! 6. Example devices Panasonic NV-F125( NV-HD100AM) ,NV-F75,NV-F65,NV-FS 200 HQ, The best Choice NV-W1! 7. At last For the BEST QUALITY HI-FI Audio on VHS Need Recording ON NTSC ,4.43 ,EP or SLP ON PAL, LP , Black screen Video input or Black screen Generation, Don't forget about input Voltage! When doo like that on the result getting Quality best then any professional Reel To Reel And DAT is well plenty models not giving that results ! Analog sound is the best ! :-)

[@chuheihkg]

I personally knew about that, VHS is high availability, small, compact, can be extremely great if properly used. The question is about the AC-IN. AC transformer is the major problem of VHS recorder.

[@mbvideoselection]

​@@andodigital1 There's a lot of jargon dropping there but most of it is entirely irrelevant. The DMX (Depth Multiplex) system doesn't care about the video format and many VCRs don't need a video signal to lock on to a Hi-Fi Audio track. Admittedly some cheap ones have trouble as do the high end ones with TBC. But it's not true that an NTSC machine gives better Hi-Fi audio than a PAL one, and it doesn't matter if the recording is SP, LP or EP. Most European users would use LP mode for economy and because very few PAL decks have an EP mode.

[@2pkf3]

it still surprises me of the production quality of this channel even with only 500 subscribers. I look forward to watching every episode that comes out. Keep it up mate.

[@MadeOnTape]

appreciate the kind words! i’m looking forward to building a community 🤘

[@DarkTrapStudio]

@@MadeOnTapeYou already have a community !

[@MadeOnTape]

i am truly humbled and totally forgot this video was made with about 500 subscribers...i'm always learning and hope that sharing/showing that process is helpful@@DarkTrapStudio

[@DarkTrapStudio]

@@MadeOnTape500 subscriber is a big community, it just depend on the quality :) The comparaison was great thanks

[@billyjackoff]

The VHS has a surprisingly tasteful low end bump.

[@SirMillz]

Many times when using these vcrs to record it's good to have the video hooked up to something like a small tv. This may help reduce hum and noise by not leaving that jack open. Also, yes, you need to pump the levels. VCRs have awesome compression and can handle a lot of gain. This is important when recording with vcr.

[@MadeOnTape]

excellent advice! definitely more exploration of the VCR down the road. thanks for watching 🙏

[@WillemdaGuide]

What could be used best to pump up the levels? Any advice in type of device or model or brand?

[@SirMillz]

@WillemdaGuide I only mean that your gain. What ever you are using (mixer or amp) to bring sound into the vcr. The vcr has its own compression and is really good and handling some amount of gain.

[@WillemdaGuide]

@@SirMillz thanks for your reply, I can pump the output level of my 8 track casette but might it be worth to put an pre-amp in between, or maybe an eq? Just thinking up loud. Thanks again!

[@SirMillz]

@WillemdaGuide sure, a preamp will work. You can always experiment with it until you get the desired sound you are looking for. I do recommend hooking coaxial video up to something like a small TV, which should help reduce noise. One reason you want to go in with a lot of gain is to reduce that sound to noise ration. But, you probably know this. It's recording science 101.

[@SeriousThingsTomorrow]

I've just discovered your channel over the last few weeks - amazing videos and good tunes too! 🙏

[@MadeOnTape]

thanks for tuning in and listening! i like your name “serious things tomorrow”

[@SeriousThingsTomorrow]

@@MadeOnTape Thanks man! I make music under this name too - my Portastudio 414mkII is heavily involved!

[@MadeOnTape]

nice! i’ll have to check it out!

[@Isaackvillani]

Oh my gosh I just found my favourite KZbin channel in the WORLD

[@MadeOnTape]

that means a lot thank you!

[@ebbtiderecords3767]

Hey, man. This is a great channel!

[@MadeOnTape]

hey thank you so much! 🙏🤘

[@materedai4158]

I was born in 2000. I just plugged our VHS player into a TV because my grandma wanted to rewatch my parents' wedding. The sorry zoomers part hurts so bad:"D (btw I think you got a new sub)

[@MadeOnTape]

ahhaha i adore my zoomer friends and will be the first to go to bat for them but still gotta take jabs here and there. Thanks for watching and hope the wedding was cool! 🤘

[@materedai4158]

@@MadeOnTape oh yeah, it was cool as heck, people in 1998 were different😁

[@drgeorgejohnson]

This is unbelievable content…searching for the tape answers and came across it…thank you… …BTW…um, am I the only one that thought the VCR sounded the best?…

[@ChristEnlightening]

Same here…I actually hear more hiss coming from the TEAC!?

[@MadeOnTape]

thanks again George!

[@gforce7four]

Great point. I'm an Xer that has to work at a PC most of the day. Love my DAW but am very interested in getting "off the grid" and using a VHS would make perfect sense in conjunction with an analog 4-track recorder. I want to get back to pure creativity that doesn't involve a mouse or keyboard. Thanks for the idea and inspiration! Keep up the great videos.

[@MadeOnTape]

thanks for watching and listening!

[@godofspacetime333]

Just found your channel, great stuff, I’m sure you’ll be growing quickly. One suggestion I’d make on A/B’ing sources for comparison - don’t make the cuts on beat, make them at completely random intervals. I find the differences are easier to hear that way on videos like this, maybe that’s just me though.. I realize it’s more of a pain when lining up different mixdowns coming from a cassette deck, but I think it’s worth it.

[@MadeOnTape]

that’s a great suggestion! i think my type-a nature is why i put the change on downbeats. honestly the way i do it, it would be just as easy to make random. Thanks for checking it out!

[@stabbyjosh7931]

Back in the early 90s, in what I now call "The Dark Years". I used to work at Radio Shack. And back then they still sold RtR, DAT, and DCC. But by far, the most popular recording media for garage bands and hobbyist musicians, was Hi-Fi Stereo VHS. You did have to have a pure audio source though. The recording quality was so good, that there was no noise reduction built in.

[@MadeOnTape]

thanks for sharing!

[@njm1971nyc]

Not so. VHS HiFi uses a system very similar to DBX. It's just "on" all the time, and not "advertised" to the consumer. There's no need for anyone (except an engineer) to know what's going on inside the machine.

[@mbvideoselection]

@@njm1971nyc I don't think so. I think you're getting confused with the term DMPX which simply means Depth Multiplex, which refers to the deeper magnetic footprint that the audio signal occupies on the tape in relation to the video signal which non-destructively gets recorded over the top.

[@njm1971nyc]

@@mbvideoselection umm, nope. 🤷‍♂️ Nothing to do with it being depth multiplexed. I remember a very boring talk with my slightly creepy boss at Technicolor Videocassette (when I was a "cute teenager" and he was a suspiciously single older man, hahaha, if you know what I mean!) anyway, he was singing the praises of LINEAR audio (seriously!) and slagging-off HiFi audio (or HD, High Dynamic, as Panasonic called it in the early days), because of its rather extreme DBX-style companding system. I still remember the graphs he showed me to illustrate his point. To be fair (to him), the linear audio of the JVC BR-7000 Duplicators was very good, but consumer VHS decks pretty much all had horrible linear audio heads/circuitry, so his point was rather moot. Copying/pasting this next paragraph, for the sake of speed... "VHS-Hi-Fi system inherently uses a decilinear companding system that is nearly identical to dbx in function and operation. The companding is an integral part of the Hi-Fi spec, it cannot be disabled or avoided, and is in every VHS Hi-Fi recorder."

[@Valerifon1]

I think the VCR sounded best - no question about it to my ears. The flattest (lifeless - not frequency response) was direct into the computer. The reel-to-reel came in at a close second. Great video! Subbed your channel. 😎👍

[@MadeOnTape]

thanks for watching listening, and subbing! let me know if there’s anything you’d like to see down the road! 🤘✌️

[@dalil260175]

Is it possible to get that warm tape saturated sound using vcr instead a reel to reel?

[@MadeOnTape]

that's a great question! In short, not really. The VCR is very hi-def, almost like digital audio, so it doesn't impart any character to the sound like a Reel to Reel. However, if you have a really old machine, they used to use linear mono audio. I'm sure something wacky could be done with that, but again, mono. thanks for watching!

[@andypickeringmusic]

Great video! Ive recorded to hifi VHS from my 4 track, really was cool! I didn't get any added noise like yours did. Actually, I couldn't tell the difference to my digital recording, it didn't add anything nor did it take away anything to be fair to the VHS. But for that reason I didn't bother with it again. Where as My Revox A77 really adds something when you record to it! Although that is expensive to maintain

[@MadeOnTape]

ooohhh Revox A77. my VCR is SUPER cheap and i'm sure there are better ones...but like I said in the video, I'll probably use the VCR as a stereo bouncing machine. Thanks for watching!

[@andypickeringmusic]

@@MadeOnTape 100 percent worth while to stay out the box

[@PaulRiismandel]

The VCR most likely has auto gain control (AGC) which is why you hear more hiss, since it’s pumping up the gain on the lower levels. If you added more gain ahead of the VCR, like you suggested in the video, that would just effectively compress your recording.

[@MadeOnTape]

yes! thank you for sharing!

[@chrisharding5447]

Older video recorders also had level adjustment for audio. I have a working,, although ancient recorder that also, when a number of tracks were recorded on it, you could search them using the blank space between them...

[@BogoEN]

Different VCR’s can give you different results, but one thing to look for when doing this is changing from SP to EP tape speeds. It’s a little counter-intuitive, but most folks find that recording at the slower speed results in the same audio quality (and also may remove the hiss 🤓). Awesome video - maybe do a follow-up at some point! I’ve done stereo mixes with almost no audible hiss from a DAW. Cheers!

[@MadeOnTape]

that is counter intuitive! i was planning on exploring EP vs SP, and some other follow ups... thanks for engaging!

[@michaelslaughter7537]

@@MadeOnTape, I did some recording on VHS back in the 80s. I recorded a CD onto videotape at the slowest speed. Playing both back and switching between the two, I couldn't hear any difference. You can get 6 hours of better than reel-to-reel quality on a VHS tape.

[@rolandogamez]

Its actually pretty simple. MOST of the tape/head speed comes from the spinning head, not the tape moving. Video was severely affected, but audio, not so much!

[@tapetwo7115]

There is no audio quality different between SP and EP when it comes to HiFi VCRs. It's a PCM audio track encoded. The only difference comes to physical quality and deteriation of the VHS tape itself. If it's degraded in certain areas, the HiFi track could drop out resulting in spots that send the VCR back to playing the linear mono audio track. And that's where quality matters the most. When recording linear/mono track, there's a huge difference between SP and EP. Fun fact, if you have a VCR that has the "Audio Dub" feature, you can actually overwrite just the linear audio track. This is how radio stations saved money on tapes on LP (mid range speed) with 160 minute tapes recorded in LP. First, play two shows at the same on separte channels. HiFi Lch = Show 1 HiFi Rch = Show 2 then re-record on same VHS tape using 'audio dub' feature only to record over: Linear Audio Mono = Show 3 all on a single tape lol -- RECing on any HiFi Stereo VCR will always record the HiFi and Linear tracks. But Audio Dub is a VCR editing feature that lets you overwrite just the Linear track. We learned this when editing wedding videos for clients when they would take their master tape home and only hear the original edits/raw audio...telling them to set their HiFi VCRs to mono or to watch a copy of the tape we provided that was mono only.

[@drbbhiggins]

I recorded the a hip hop album on a HiFi JVC vcr back in 1998. That vcr had an independent audio recording function that allowed you to adjust the input recording gain. IMO nothing sounded better than the warmth of that vcr analog tape. Was able to reduce the hiss because of the independent audio gain function that vcr unit had. At the time my four track unit had stopped working and we did live takes of all the songs for the album. A Shure sm-58 through outboard compressor and slight reverb and the tracks straight through an Ensoniq ASR-10. All ran through a Yamaha 12 channel board right into the vcr. When you're a broke producer/engineer you get creative. Came out great.

[@MadeOnTape]

amazing! thanks for sharing! i think i would still be interested in a VCr that has independent audio 🤔

[@elnyoutube123]

Do you remember what model it was?

[@MicrophonesInTheTrees]

The analogue warmth was imagined. It's not recorded onto tape like an audio tape. It's non-linear FM.

[@neilmilne6278]

Enjoyed your vid, and thought I would share my experiences with this largely unknown VCR "Hi-Fi" audio capability. I used HI-FI vcr's for video dj work back in the 80's. At that time, Music video audio was terrible, so I would put together versions with decent audio quality myself. After capturing a good quality video source, I would use this to record a 2nd generation video source syncing it alongside audio sourced from a CD or Vinyl and record it onto a Hi-Fi VCR. I would then have a CD quality music vid to use on a pretty serious dj set up, video projector and big screen. This was hard or very exspensive to achieve in the 80's and even into the late 90's. A few have made comments around the audio being linear and not helical scan. While its true there has always been a linear audio path and some even marketed a "Stereo VCR" which in reality just split the mono linear portion of the tape and used half the track for left and half for right, the sound might be stereo, but still garbage. These are NOT the Hi-Fi vcr's which this youTube vid is refering to, and yeah, they probably do belong in a recycle bin. For it to be useful at recording and playing back decent quality audio, there needs to be the words or a symbol "Hi-Fi" printed on the facia or tape loading flap or somewhere on the front. "Hi-Fi" identifies it as having the helical scan audio function and from my experience, if you want to get the best out of one of these, choose one with audio record level controls. The short falls as already commented on by others are real, being head switching distortion and pumping. Some manufacturers offered better quality more expensive machines, or specifically targeted the audio function rather than just improved sound for a video soundtrack. They spent more time and R&D minimising or working around these issues. Most people wont notice or care, but if your a critical audio listner and / or have a decent sound system, you will. That said, they were and are a very cheap method of bulk recording at great quality. (outside the digital realm) The first hifi vcr's were quite a bit more exspensive than a standard vcr with the pick of the domestic units being the JVC HR-D725. Very well built unit with excellent picture quality, minimal head switching distortion, manual level controls and great functionality. While I lusted after one of these, at the time it was just too exspensive, but I found the NEC 895 to be a badge job copy of the JVC for a lot less $ so ended up with the same that I could afford. I bought or hired quite a few makes and models over the years using a number of them for DJ work and music for parties etc. The other quality machine of mention would be most of the Panasonic models and a couple of the high end Mitsubishi's... If its an SVHS and a high end model even better. A lot of the cheaper units I trialled did have the head switching distortion issues, and definately the pumping issue were there was an auto gain control (AGC) used instead of Level control. One other comment I'd make, being as the helical scanned Hi-Fi audio layer is below the helical scanned video layer, better quality tape will allow the recording to last better as far as dropp outs. It's true you can use any tape and get similar results if the tape is sound, but being a magnetic tape it will suffer degradation over time and more so with el-cheapo formulas Hope someone finds this interesting or useful. Cheers !

[@MadeOnTape]

I found this very interesting and useful! thank you for sharing your thoughtful experience!

[@drgeorgejohnson]

Holy shit that was all very useful and interesting AF. Thank you. I am stumbling across this looking for a secret way into getting into tape but doing something different that still sounds great. I feel like the VCR sounds the best in this video and I have always loved the sound of VHS tapes I do not know why, I think I may go this route, any thoughts for me?

[@drgeorgejohnson]

BTW, I’m trying to understand something here. It seems to me that the difference in sound quality should have been greater, seeing as how the TEAC is producing a Lofi signal while the VCR is Hifi. Can someone explain this to me?

[@JMP_2203]

Cool video. FYI, the helical scan only applies to video. The audio track is recorded / played back linearly with different heads.

[@JMP_2203]

I stand corrected - I read your pinned comment. I didn't know there was a difference between linear stereo and hifi stereo on VHS. Thanks - and again, great video!

[@Twobarpsi]

When we played live, I would record all the audio off the board into a VHS tape. 2 hours of audio on one tape! The frequency response of a HiFi VCR, is really good!

[@MrSlipstreem]

Or very bad. There was such a wide spread of performance between different VHS HiFi machines that it's not possible to give a blanket "really good" rating to them.

[@Xantylon74]

I could hear the hiss on the R2R, VHS had some rf noise because of the (not recorded) Picture, but it did sound as good as your R2R.

[@xtraflo]

My "Gut" reaction was that they were all the same - direct recording to computer.

[@str0ngerthan0ceans]

I have so much love for this channel! I'm gonna dig out the vhs tomorrow haha

[@MadeOnTape]

thanks for being a part of a budding community! 🙏

[@4headgaming448]

I just found your channel and I’m absolutely hooked

[@MadeOnTape]

that’s very kind of you thank you. let me know if there’s any topic you’d like to see covered on the channel!

[@SFtheGreat]

And labels still release stuff on VHS, like me. You may want to use a VCR with a manual volume control, like the Panasonic NV-F65HQ, that was literally made for audio, it doesn't even do video in LP mode.

[@MadeOnTape]

i've got an ebay search saved for one of these! Definitely looking for more control in the audio recording. thanks for the tip and watching!

[@SFtheGreat]

@@MadeOnTape If you want a better pro equipment, then there are such devices as JVC ERA, or something form Sony's pro line, I have a DVCAM deck from the latter.

[@Nathriel]

Holy crap this video is straight out of the 80's man... and provides useful info with style?! Subscribed! I'm actually about to demagnetize my Akai X-165D's heads in preparation to make a mixtape from my Technics SL-1200 MK6 (Japanese model).

[@MadeOnTape]

thank you for the nice words and have fun with that Akai!!! 🙏

[@soundofthegardenwatc]

Do you have a video talking about how to put Reel, VCR, or tape deck in analog chain?

[@MadeOnTape]

not sure what you mean specifically? a chain has so many links... happy to answer!

[@zarrenrhys06]

Wrong info the revolving head intend video only theres a separated audio head beside that round head

[@simplisticscientists]

I was thinking about trying this the other day when looking at the price of VHS machines compared to reel to reels!

[@MadeOnTape]

it's fun! The reels impart wonderful things into the recording, and VHS will just give you a scarily accurate recording (not all VCRs are created equal)

[@Punkfan2000]

Me and the guitarist in my band always used a VHS hifi - VCR in the 90´s for recording masters of our 4 track demo-mixes. Still sounds fine today.

[@MadeOnTape]

thanks for sharing! 🙏🤘🤘🤘🙏

[@Twobarpsi]

We did too!🤘

[@tsuwaque]

I thought 2 was the VCR and the R2R was 3

[@darwiniandude]

I'm interested to try this at heavily levels, saturated, as I know how reel to reel behaves with the levels cranked but haven't tried with hi-fi VCR.

[@frankcoffey]

VHS HiFi was very good for stereo and you can make a 6 hour party tape. Some JVC models had an improved system to get rid of head switching noise and those are the best ones for music. If there had been more development it could have been developed into the best analog recorder ever. I wish someone had done a format where all the heads were used for audio with no video track to maximize audio quality.

[@MadeOnTape]

that would be very cool! I need to find some skilled machinists 😂 thanks for watching 🙏

[@WillemdaGuide]

Any advice on those JVC models, types?

[@frankcoffey]

@@WillemdaGuide The JVC HR-S7800U for sure but any of the later ones should have the anti head switching noise thing.

[@JoshuaPickenpaugh]

I honestly wasn't paying attention to this week's listening quiz, just digging the music. The VCR did, though, have a bit more top end to my ears.

[@MadeOnTape]

thanks Josh! more new music coming

[@colloidalsilverwater15ppm88]

Hey, "made of tape" ...there is large amount of hiss on all of three formats. Or, it is a hiss from tascam? It is clearly noticeable on computer recording. Second, you have to raise the level of signal for video. In that case, hiss will be way down of your signal.

[@MadeOnTape]

💯 the hiss is from the original TASCAM recording indeed! in fact the VCR to me picks it up clearer than the other formats. i’ll definitely be exploring this more and do another video on it down the road. thanks for watching and your comment! 🙏

[@colloidalsilverwater15ppm88]

@@MadeOnTape ok, I am interested especially of recording onto vhs hifi....because they have usable counter. In theory, it is possible to know where is song, for every casssette. Second, it can be interested to make measurements with pink noise, for several models and brands. Is it possible for you?

[@MadeOnTape]

@@colloidalsilverwater15ppm88 once i have the resources, I would LOVE to do these types of experiments! Right now, I don't have the money to acquire several models and brands. Thanks for tuning in! Watching and sharing will help me get to goals like this

[@dashriprock9014]

I've gotten excellent results from a Panasonic Omnivision Hi-Fi VCR.

[@MICHIGANROCKSANDROLL]

I use JVC S-VHS to transfer old HI-FI tapes I made when I DJed back in the 1990s on HI-FI RCA decks. JVCs tend to have great sound and PICTURE as well. I started doing mixdowns HI-FI VHS From my TEAC 3340 tracks I was updating from 1978-1983. Then Computers hit in the 2000s and the better sound cards were hard to get and pricey. But the demos got did. HI-FI VHS was great except if you get the annoying HEAD SWITCHING NOISE. Around 100hz it's a low buzz. I'm sure there's a video somewhere on how to deal with it. Glad you see you caught on.

[@MadeOnTape]

love this advice! Also, as a born-and-raised Michigander, I appreciate you being here!

[@andodigital1]

Hi. what want for 1 to 1 quality on VHS ! 1. Need PAL or NTSC This is the Best Choice with 4.43 because on NTSC recording take more tape space for audio recording and Les for Video signal Then on Pal ,Left channel is 1.3Mhz Right Channel 1.7Mhz! 2. Need VHS with Long play (LP On PAL OR on NTSC Extended Play EP or (SLP)) Because on this mode lowered video quality but again take more space for AUDIO on tape ! 3.HI-FI NICAM because minimum need on drum 2 Long play Head ,2 Standard Quality play Head ! 4.Black signal generator on VHS calling this button (SIMUL) Or ( Test signal) on BACK This generate Black video signal ,need for tracking stable simulation because VHS tracking system looking this information for synchronization ! When not synchronize tracking system non stop looking and make on recording noises clicking like scratching noises ! ON VHS Without Black Screen Generation Need give in black screen video signal from another device get same results ! 5.For best result need check some VHS Without Recording Level adjustment gives the best recordings when input 5 volts but on 0.5-0.7V results poor ! 6. Example devices Panasonic NV-F125( NV-HD100AM) ,NV-F75,NV-F65,NV-FS 200 HQ, The best Choice NV-W1! 7. At last For the BEST QUALITY HI-FI Audio on VHS Need Recording ON NTSC ,4.43 ,EP or SLP ON PAL, LP , Black screen Video input or Black screen Generation, Don't forget about input Voltage! When doo like that on the result getting Quality best then any professional Reel To Reel And DAT is well plenty models not giving that results ! Analog sound is the best ! :-)

[@Duane-s7s]

Why don’t VCR’s come with headphone knack and adjustable audio input meters?

[@MadeOnTape]

i think some sophisticated ones did

[@FelixOlschewski]

Am I the only one who hears a lot more his on sample #2 than sample #3? I was surprised that #2 is the TEAC. Also I think there is something going on with the stereo image on #3. Not at all sure what it is but something changes.

[@MadeOnTape]

they certainly all hiss because of the source. those frequencies really seem to depend on the ears of the beholder and i had an interesting psycho-acoustic situation where i could easily tell the difference in the beginning, but by the time i finished editing the video, i couldn’t. to your second point: great ears! I was changing the panning on the one guitar between takes. i should have stated “i changed nothing significant between takes” thanks for watching and coming on this journey of exploration!

[@crnkmnky]

Yeah, I heard the same things, Felix.

[@brianmuhlingBUM]

Well done. During 1978, I bought a TEAC 3440 and was appalled at the signal to noise ratio. Using a test instrument set, it barely managed 50db, so I bought a dbx II 4 channel unit and that solved the problem. I was impressed with the sound quality of the VHS HiFi PCM system. All that good sound from a tape barely moving compared to the TEAC at 15 ips. That's my 10c worth.

[@MadeOnTape]

thanks for sharing!

[@scottbaxendale323]

When CDs first came out in the 80’s i did some work for the Hard Rock Cafe and they opted to use HiFI VHS for their house music instead of a mega CD changer. The sound quality was superior to CDs and rivaled 15ips Reel to Reel audio quality. We used them to mix on.

[@MadeOnTape]

thanks for sharing Scott! seemed like a great way to get a good amount of BGM

[@nathanstein589]

How did you mix on VHS? As far as I can tell you can have two individual tracks max on VHS due to it being a stereo format but that’s it I’d think.

[@chrisharding5447]

@@nathanstein589 mixing down to a stereo master is what he means. We did it live with my band straight to vhs.

[@TheGarageRecordingSC]

Very cool video. I would be really interested to see a mix done all in the box that is clean and digital and then sent through the VCR to see if it gives it any of that nice tape warmth.

[@MadeOnTape]

definitely have more plans for the VCR! thanks for watching!

[@david9572]

Back in the 1990s I used HiFi Vhs to archive FM radio shows. Although the quality was excellent then, when I try to play them now the VCR struggles to find the HiFi track. It is strange that the image quality has not deteriorated but the HiFi track has. Now most of my recordings just get played via the linear track which sounds like am radio. Any ideas?

[@MadeOnTape]

hmmm could it be the VCR itself? have you tried others?

[@david9572]

@@MadeOnTape Yes I have. The Panny is probably the best with older tapes but my 2 JVC decks are about the same.

[@jessihawkins9116]

have you tried using an outboard noise reduction system with the VCR to take out the hiss?

[@MadeOnTape]

i think the hiss comes from the portastudio recording, not the VCR

[@jessihawkins9116]

@@MadeOnTape no

[@LeoFazio]

I have a VHS handycam that record directly on tape, I'm wondering if there's a way of using it in my productions, gonna try

[@MadeOnTape]

i love to hear that! Try everything, that's part of the fun! 🤘

[@LeoFazio]

@@MadeOnTape It worked, and the sound is DOPE!!!

[@MadeOnTape]

@@LeoFazio amazing!

[@MrSlipstreem]

The VHS system you're talking about recorded a pair of FM signals to tape. Think of it as two mono FM radio stations at a time to make stereo. It used companders (compress on record, expand on playback) to increase the signal-to-noise ratio. Even though it was a standard, the quality varied wildly between different manufacturer's decks with some performing close to CD quality in some respects and others being easily beaten by a good stereo cassette recorder with correctly calibrated Dolby NR. I realise this video is now 3 years old, but be VERY careful if you intend to try pumping up the input level to combat noise. I fed mine a 2V RMS signal (a common standard for RCA jack connectors) and it blew up the input stages on my VCR. Even though it was barely out of warranty at the time, it was beyond economical repair so ended up being scrapped.

[@CPUTests]

That VCR in particular does not have manual level inputs. So it tries to amplify quiter parts of the signal. There are VCRs with level input pots just like a tape machine and on those hi-fi vcrs it's the same as PCM 44 kHz 16 bit digitall as a matter o fact that's the way it is encrypted on hi-fi VCRs.

[@zordmaker]

HiFi VCR uses companding circuitry to get that crazy high S/N ratio. So depending on the material you will hear the difference as there is a slight delay expanding the compressed audio on playback.

[@MyDenney]

Could anyone respond? How do I record audio/ music onto vhs recorder without VU meters. Input vol. controls? Reel to reel has them, so do cassette decks. I have a hi fi vcr. The sound quality is excellent, but no meters. How do you record when you don’t know what the input signal/ volume is? How do you make a good recording without them?

[@MadeOnTape]

my first suggestion is to just try and see how it sounds! The audio isn't being recorded like on a R2R, there's some kind of FM signal being produced and layered into the tape, so there's almost certainly none of the traditional value of a tape machine where you push it harder for saturation. Just a fun clean analog sound! Hope this helps and thanks for watching!

[@MrStarbor]

GREAT NARRATION PAL -BRAVO!!

[@kcat80]

I think I actually preferred 1,2 for overall eq balance on the mix. I think 3 lost a bit of low end somehow? which seems weird because the frequency response should go all the way down to 20hz. maybe different vcr's make a difference? perhaps there is a more distinct roll off? the hiss did seem louder to me on the reel to reel.

[@MadeOnTape]

the differences are so subtle to me but i prefer the reel to reel probably because that’s where this music has been made so far... definitely more vcr experiments coming! thanks for watching 🙏

[@georgeprice4212]

I didn’t hear THAT much hiss with the vcr, though. And I already knew that vcr’s could be used for music: Radio Shack used to put some music CD’s on vhs tapes at one of the stores here in Houston in the 80’s (before Stereo VCR’s were available) just to have music in the store.

[@scottpeters4401]

This is so cool…I have never even thought about recording sound into a VCR…I am in my mid 50’s,so I remember VCR’s very well…I had a HiFi VCR that sounded amazing back in the 80’s…but that was pre digital anything…except watches and calculators….I didn’t know you could just send audio into it….I may dig mine out and give it a shot….Absolutely great video..just found your channel by accident..I am subscribed now..I gotta see more..

[@MadeOnTape]

thank you for sharing! Happy recording!

[@Ka-tz4gp]

After all of that I am mostly interested in what Tascam model you are using? Can you be so good to share that info?

[@MadeOnTape]

hello! it’s the TASCAM Porta Two! (not to be confused with the TASCAM Porta 02) almost everything on my channel is based around it. thanks for stopping by and watching! 🙏

[@valterbitzproduction129]

Wow! Good experiment!

[@LeoFazio]

This channel is exactly what I needed, thank you!

[@MadeOnTape]

that's very kind of you! 🙏

[@mdrummond194]

Would the vcr work standing on its end? Humour me please….

[@MadeOnTape]

I'm not qualified enough to give a definitive answer on this. However, I will say I have opened up the inside of a few VCRs and my strong hunch is that these machines were not meant to work in any other position. The tape path is quite elaborate. I also have never seen one operated standing on its end. But...I am also the type of person to say: if you don't have much to lose, you should try it! I assume you're having issues with horizontal space? What's the worst that could happen? The tape gets all jammed up? No one will get hurt hahahaha

[@paulleftwick7782]

would earthing vcr help with hiss a usb when earthed comes out cleaner ?

[@MarcoAzevedo]

Cool channel man and thanks for all your vids!! I can hear a difference on reel to reel PAN. It is not centered, has more sound on right side

[@MadeOnTape]

good ear! i had more issues with that back then and have dialed it in better these days 🙏 thanks for the kind words and let me know if there’s anything you’d like to see on the channel!

[@MarcoAzevedo]

@@MadeOnTape cool and sorry my newbe english... i've been use an hi-fi stereo Panasonic VCR to two mics drums rec with very cool results, may be you have more nice tips to share. Thank you!

[@jn3750]

Billy Joe; a 4 track Teac R2R deck canNOT compete with a hifi VCR (with higher/wider frequency response). Only a 2-track professional r2r machine can. Audiophile.

[@drgeorgejohnson]

I’m trying to understand something here. It seems to me that the difference in sound quality should have been greater, seeing as how the TEAC is producing a Lofi signal while the VCR is Hifi. Can someone explain this to me?

[@MadeOnTape]

hi George! thanks for watching. A big reason here is the source material, a cassette portastudio recording, is definitely lo-fi to start. Also, the TEAC is considered a hi-fi machine. Hi-fi and lo-fi don't have any numerically defined values. So, the experiment here was to see if the VCR sounded as good as the TEAC for mixdowns or external bouncing. I hope this all makes sense!

[@johntait5141]

Very cool and informative vid as always. What immediately comes to mind are successfully transferring any recordings done on blank VHS tapes to digital ( for combining tracks, etc.) , the hiss and how to eliminate it without the classic noise reduction, and how to actually check recording levels while recording onto VHS.

[@MadeOnTape]

some VCRs had recording levels, but mine is an inexpensive model with a built-in limiter. Experimentation is the name of this game!

[@edie_online-q4g]

This is awesome . I have been walking by one of these everyday at my parents place and just stumbled across your video. Love your channel

[@MadeOnTape]

ah thank you! you can have fun with it, and I'm sure i'll make more VCR videos down the road.

[@MyDenney]

No one talks about hi fi VCR’s that have no audio controls or VU meters. Why did they stop putting these needed features on VCR’s? I know some do but most later VCR’s didn’t have them.

[@MadeOnTape]

I can only assume companies like Sony wanted to make machines with massive appeal that were as affordable as possible. The audio controls were rendered to a built in limiter, like on my machine, and nothing else.

[@DannyOKC]

I thought three was the Tascam because it had less bass. I never noticed any hiss. QUESTION: I experimented with bouncing from my Tascam 414 to my VCR for the first time a month ago, and I had no idea how to figure out the levels. The first time, I got lucky and it was good. The second time, the signal going in was too hot. Is there a simple way to get this right, or some sort of rule of thumb on this?

[@MadeOnTape]

great question! this will definitely be a topic of a future video... i think i’m right to assume that a VCR is expecting master-level audio from a finished product, so I would think it would be difficult to go directly in too hot into the VCR. is it possible you overloaded your outputs on the 414? or maybe there’s something going awry with the VCR? This is just a guess, and i do want to look into this for a future topic. Just for reference, when i exported the audio from the VCR to Logic, the signal level was nearly identical to bouncing straight from the TASCAM, so hitting like -12 dB give or take a few dB.

[@DannyOKC]

@@MadeOnTape I dunno. I feel blind. I have the 414 running out to the VCR. The only thing I have to go by is the master fader on the 414. I can't hear what the VCR is hearing, and there's no meter on it. I'm sure I could figure this out with half an hour's worth of experimentation, I just thought maybe there was something obvious I hadn't thought of.

[@MadeOnTape]

@@DannyOKC we're all blind together. Let me know if it works out!

[@380stroker]

-10dbu is for consumer playback systems.

[@DannyOKC]

@@380stroker Does that mean I should have the level coming out of my Tascam at -10dbu? Or do you mean when bouncing back in from the VCR I should have the Tascam meter at -10dbu? (Please forgive my ignorance on the subject.)

[@schindlerific]

This is great! I was just about to throw out an old vcr. Glad I saw this

[@MadeOnTape]

you were about to send it to Radio Shack heaven

[@jamiey5779]

Some Hi-Fi VHS models had a digital display that would show the line inputs audio levels while also allowing user adjustment.

[@MadeOnTape]

for sure! maybe one will show up on this channel down the road??? 🤔

[@bdalbor]

Excellent video! I'm really impressed by the quality of the production! Just one thing, though. VHS was always called "Video Home System," even as far back as its invention in 1976. The "Vertical Helical Scan" connotation is somewhat false. VHS home recording wasn't exactly vertical (the heads of a VHS VCR run at an angle, and as a result isn't vertical), and while VHS VCR's did record video helically, the patents of this form of tape recording belong to Ampex (back in 1961). JVC would have had to pay Ampex royalties to use that name as a result. There are articles from Popular Science in November of 1977 that debunks the use of the "Vertical Helical Scan" name. That's just me being an OCD internet pedant though. This video was really good and informative otherwise. Keep up the excellent work!

[@MadeOnTape]

yes! since publishing this video i learned that i was perpetuating a myth! if youtube let me cut in an edit i would have 😂 thanks for the kind words and insight 🙏

[@xNYCMarc]

The audio on a "Hi-Fi" VHS is also recorded helically, not just the video. Hi-Fi VHS recorded an FM carrier along with the video. The audio was carried within the FM carrier.

[@larryshaver3568]

i have a couple of that model vcr, they have great sound

[@adam207321]

The noise floor was horrific with the reel to reel and the VCR was sort of between the reeler and the computer so it was pretty obvious. VCRs have a great technological advantage over reel to reels, though this could be compensated with a compander and running 15ips..or if youre a maniac 30ips and a compander and you dont have a chance of distinguishing it from a computer

[@MadeOnTape]

thanks for watching! Yes, there's a lot more to explore in detail here. I love your 30ips maniacal comment 🤣

[@adam207321]

@@MadeOnTape IT IS A MANIACAL THING...I mean 30IPS???? damn thats a lot of tape realestate not to mention the utter crap bass response at those speeds xD. I have myself gone with a 7 1/2 IPS setup on a half track and its more than sufficient for mastering. I have mastered a few unreleased songs to my quarter track stereo machine before the mods and its still great at 7 1/2ips . The deal with poor bass response at 15ips and above is the wavelenght recorded onto tape is far too wide to be reproduced in any meaningfull amplitudes for the playback amplifier to record.. anything at or above 15ips is loosing low end (20Hz). And to my knowledge there is no manufacturer making heads with wide enough gaps for you to be able to run 30IPS and reproduce 25Hz... Sad. And its not like higher tape speeds would allow you to obtain more bandwidth either because your high frequencies get erased by the bias frequency. I just modified my old poor crappy tape deck to be something respectable instead and maybe in the future Ill be able to build something myself.

[@michaelkonomos]

So funny but I had guessed that 2 was VHS and I actually found 1 and 3 to be less distinguishable. I wonder if all the different ways we hear has to do with individual human loss of certain parts of spectrum as we age?

[@Noise-Conductor]

The human hearing frequency range is 20hz-20khz. Most people over 35 can't hear past 16khz. then you gotta factor in your headphone or speakers (& the room). No two people hear the same thing, the same way.

[@rogerturner1881]

Wondered whether they could have done a HHS [Horizontal Helicon Scan]

[@MadeOnTape]

ahhh a smarter person than i could know 😂

[@justinellison4214]

Well i have a vestax mr44 but it iant perfect it has some whineing noise in it but i can work around it .

[@MadeOnTape]

thanks for sharing Justin!

[@TotallyGoodatGames]

I've heard tons of audio comparisons between VHS, multitrack cassettes, USB interfaces, reel-to-reel machines, and so on and I literally can never tell the difference between any of them. Maybe it's just because KZbin audio is downgraded to 128 kbps, but in my humble opinion it doesn't really matter what medium you record to because they all sound the same. So, do which ever one is more fun or more practical for you!

[@MadeOnTape]

this is the essence of my entire channel summarized ! love it and love your comment! 🙌🙏🤘

[@TotallyGoodatGames]

@@MadeOnTape 🥺🥺🥺🥺 thank you!!! 🥺🥺🥺🥺

[@boliverfilms]

Suddenly, goodwill/salvation army stores and pawn shops, across the globe, are being emptied of VHS technology. Great video, man! Thank you for what you do. Stay analog AND analogical, my friend...

[@MadeOnTape]

analogical! love that, thank you!

[@coolerthanyou9548]

i guessed that 2 and 3 were the VCR and tape respectively, they sound so close i couldn't tell, but i could tell the TASCAM instantly

[@RobertWilliams-kw5dl]

I used to use a hifi VCR alongside 4 and 2 channel tape recorders in the 80s. My VCR was relatively rare in having manual record level and metering. Some VCRs were not hifi, because they used a low speed linear track. Mine offered a spec of 20 -20K and 90dB s/n.

[@MadeOnTape]

manual record level and metering would be bomb

[@samot1808]

Great channel man. For these tests I think you should be using more hifi input sources. Drum machines are already very lo-fi so the higher end of the spectrum (were the most difference is imo) is not really being tested here. I though 1: PC, 2: Reel, 3: VCR but unsure about 2 & 3. PC was obvious because of lower noise.

[@MadeOnTape]

yo thanks for the kind words! I had no idea how popular this video would be when I made it so I may revisit the topic with more hifi input sources in the future. Cheers!

[@samot1808]

@@MadeOnTape keep ‘em coming!

[@jamesgambino7170]

Man! The last video I commented on hooked me with that same tape deck I have, but serendipity lead me to this one after I just sorted through tons of older high end VCR recording and mixing equipment I almost just got rid of. Thanks for the new inspiration.

[@MadeOnTape]

there’s almost always a way to utilize old stuff! Sylvia Massy is a big inspiration for me in that department. thanks for checking out the channel 🤘

[@chrispeterson73]

Alesis ADAT machines also used VHS tapes, and they can be had for very little 💰 these days. Cool video! I really enjoyed the comparison between all 3. 👍🎶👂🙂

[@MadeOnTape]

thanks for sharing and watching! 🤘

[@PsychoStueyHappyKittens]

"I don't want to get into the physics of this. I'm not a physician..." Oh god, I'm stealing this.

[@MadeOnTape]

take it! thanks for watching 🙏

[@rottingsunrecords666]

I was able to tell fairly quickly. Not having a level meter on the VCR is somewhat of a problem. If you knew you were sending a loud enough signal it would probably sound better than the reel to reel. The flutter gave the reel to reel away and the tape hiss gave the vcr away.

[@chadjohnson-authormusician8072]

Great video! I think maybe if you used an SVHS (super VHS) machine the hiss might be better. I remember hearing about this trick back in the day, and it was always with an SVHS machine. That said, I've never actually tried it, and it was really great to hear your comparison. I was surprised how good it sounded, and it was yet more proof that I think my hearing it getting more and more compromised with my age, because I couldn't hear the hiss you were talking about. I put my headphones on and held them close and listened again without watching the screen, and though I could hear slight differences in the bass (mainly), I certainly didn't hear one jump out as filled with extra hiss. Sucks getting older! :)

[@MadeOnTape]

to be fair, i only noticed the hiss when i first made the comparison...my hearing isn’t 💯 and i could barely tell the difference by the time i finished editing the video 😂

[@chadjohnson-authormusician8072]

@@MadeOnTape Well, that makes me feel a LITTLE better. :o)

[@MadeOnTape]

@@chadjohnson-authormusician8072 it's a really fascinating microstudy on ear fatigue, even at low volumes.

[@BogoEN]

From what I learned about it, SVHS only offered a boost in picture quality, the hifi signal was the same.

[@andodigital1]

Hi. what want for 1 to 1 quality on VHS ! 1. Need PAL or NTSC This is the Best Choice with 4.43 because on NTSC recording take more tape space for audio recording and Les for Video signal Then on Pal ,Left channel is 1.3Mhz Right Channel 1.7Mhz! 2. Need VHS with Long play (LP On PAL OR on NTSC Extended Play EP or (SLP)) Because on this mode lowered video quality but again take more space for AUDIO on tape ! 3.HI-FI NICAM because minimum need on drum 2 Long play Head ,2 Standard Quality play Head ! 4.Black signal generator on VHS calling this button (SIMUL) Or ( Test signal) on BACK This generate Black video signal ,need for tracking stable simulation because VHS tracking system looking this information for synchronization ! When not synchronize tracking system non stop looking and make on recording noises clicking like scratching noises ! ON VHS Without Black Screen Generation Need give in black screen video signal from another device get same results ! 5.For best result need check some VHS Without Recording Level adjustment gives the best recordings when input 5 volts but on 0.5-0.7V results poor ! 6. Example devices Panasonic NV-F125( NV-HD100AM) ,NV-F75,NV-F65,NV-FS 200 HQ, The best Choice NV-W1! 7. At last For the BEST QUALITY HI-FI Audio on VHS Need Recording ON NTSC ,4.43 ,EP or SLP ON PAL, LP , Black screen Video input or Black screen Generation, Don't forget about input Voltage! When doo like that on the result getting Quality best then any professional Reel To Reel And DAT is well plenty models not giving that results ! Analog sound is the best ! :-)

[@popturco1098]

yo signed in just to comment, anyhow here's my 2 cents, cause I guessed them all correctly. keep in mind it could be lucky guess but here are the things that tipped me off: 1 / The computer: All around highest clarity and less artifacts , the swells on the right channel gave it away 2 / The Reel 2 Reel: The innate EQ curves due to the nature of the tape composition and recording/playback standarts cause it to have a shelf around mids/mid-highs (by todays standarts I assume [as in with the luxury of our contemporary technology as Hi-freqs would be more diffucult in the yesteryear to produce and distrubute] ) and their own characteristic saturation and compresssion. 3/ The VCR: Well kind of like the reel to reel with these differences, Higher speed = More high frequency content and the characteristic saturation / compression is different than that of the R2R. Let me know what you think!

[@MadeOnTape]

hey there! I think that's an excellent assessment. What i'm loving about the comments is that most people can easily tell which is the computer. Thanks for signing in and checking it out!

[@JorgeCastro-ju7sy]

El cabezal de audio no es el circular. Ese es de video, el de audio es el cabezal normal de la derecha.

[@bob4analog]

I saved so many songs VHS HiFi. It rivals digital. Sounds absolutely Awesome!

[@MadeOnTape]

📼🤘

[@Bobklijn]

Listening test was very insightful! I am actually thinking of using my old Sharp Hifi Stereo VCR for recording audio for various compilations. While first I was expecting VCR to be the highest quality of the three sources, my ears happened to be chosing for option 2, the RTR. Unfortunately, this is the most expensive option. I hoped VCR would win, but to my ears RTR did. More punch in the sound, in some way.

[@MadeOnTape]

well, the source material and how you mix into certainly matters! the VCR won’t change much to the sound whereas the RTR will! But if you plan ahead, anything can work! thanks for watching and listening! 🙏

[@Bobklijn]

@@MadeOnTape you're welcome. If I read your reply correctly, I guess my perception of the sound of RTR could be somewhat biased, cause it seems to.have more "punch" and "warmth" which could technically translate to some kind of added distortion. This may also be the reason for the current vinyl revival,.cause.people experience distortion as "warmth". Anyway, I would still go for accuracy and actual HIFI, so I.ll go for the VCR and try to boost the incoming signal in order to reach best S/N ratio.

[@Gezira]

Good job. I've always wondered. Not bad. It was clear to me from the beginning the source material but I wasn't sure about the other two. The VCR in my simple setup (old laptop, old cheap headphones) shows a larger spectrum.

[@MadeOnTape]

it’s definitely a fun thing to mess around with for very very cheap 🤘

[@jlbfjlbf]

i enjoyed the video, back in the day i used to record my band rehearsals straight from the sounddesk on vhs tape, it sounded way better than recording onto cassette tape

[@MadeOnTape]

oh that’s fascinating! so you mixed your band through console and recorded the stereo track? thanks for sharing!

[@Mist8kenGAS]

my guess was: 1 - reel2reel, 2 - cassette, 3 - vhs i wasn't expecting cassette to be noisier than reel2reel, that surprised me though haha on hifi vhs, the audio quality is great i think the bitrate is a bit lower than 44.1khz but pretty close to near-cd quality (for me anyways) but on 2 head vcrs, the audio quality is about half that (which sounds about right since on hifi vcrs, there are usually 4 or more heads on the drum)

[@jonoftheford]

Does the VCR offer any of the magical compression and saturation qualities that reel to reel devotees swear by?

[@MadeOnTape]

it absolutely does not impart saturation qualities. There's an argument for its limiter, but you gotta experiment yourself! ultimately, if you have one lying around, it's worth trying out, but I wouldn't go out of my way to acquire a VCR for music production. thanks for watching!

[@Prod.Countryjames]

How did you connect the vcr

[@MadeOnTape]

hey! it takes RCA cables and you can get RCA to 1/4” adapters for interfacing with other gear

[@Prod.Countryjames]

@@MadeOnTape

[@mwatkins0590]

i was sitting here hoping the VCR was number 2 because the way its effecting the kick drum sounds really nice compared to 1.

[@spookdeville7916]

I came from Facebook, your sister posted this, so I gotta leave a view cause she cool af. My name is spook DeVille on Facebook🖤✨

[@MadeOnTape]

she IS cool af. thanks for stopping by and checking it out! 🙏🤘

[@staceyyoung4802]

some of the first affordable multi track digital recorders that came out were the Alesis adat SVHS 8 track tape machine..I remember trying my Mitsubishi vhs recorder in the 80's it was a hifi deck but when only recording audio into it, it seemed to have some flutter in the sound... parhaps vcr decks got better over time because my deck was early on...

[@MadeOnTape]

curious if today that flutter would be desirable for some applications!

[@kirkendahlvoyd]

I also use VHS to for mixing or backups.

[@illegaloli]

That's what I wanted to know. Thank you very much!

[@MadeOnTape]

Happy to help!

[@Rudolf_Edward]

So… you are using a thin multitrack based compact cassette as a source to compare the quality between a reel2reel and VHS-Hifi…?

[@MadeOnTape]

isn’t it crazy that you can STILL hear the difference? 🙏🤘✌️