MAKE A AWESOME MOTORIZED SLIDER

  Рет қаралды 2,902,366

Mr SunY

Mr SunY

Күн бұрын

Пікірлер: 354
@kalan4787
@kalan4787 4 жыл бұрын
That's a very green motor you've got there. Powered by pizza and beer.
@DIYDomTheBuilder
@DIYDomTheBuilder 2 жыл бұрын
Reminds me of how a roller coaster has wheels on opposite sides of a rail… Very simple design that just works. Still, curious how much the friction increases once there is a load put on the slider. Poss. Idea for a 2.0 version… Create a slot for the heads of the bolts, so they cannot rotate. Bend bolt out 45°, then add 1st roller bearing, bend back 90° & add 2nd bearing. The slots on top of the slider will ensure the head of the bolt does not rotate & maintains a perpendicular alignment of the 45° & 90° bends. Now, with the roller bearings being perpendicular as well, they will sit flush the the corners of the square tubing; which should significantly improve the coefficient of friction between the slider & the tubing after a load is added to the slider.
@nancycook3733
@nancycook3733 11 ай бұрын
I like the adaptability of the slide ! Great work but one question .......... Where's the motor and the hooked up system ? , .........
@jonnyshoestring9368
@jonnyshoestring9368 5 жыл бұрын
The motorised part was what drew me here, so little disappointed that it's not shown. The actual build and versatility is impressive, given it covers different angles, it's also nice that it requires no special tools. Nice vid!
@hayarkarabila6128
@hayarkarabila6128 4 жыл бұрын
J
@hayarkarabila6128
@hayarkarabila6128 4 жыл бұрын
Cgvgghhjvh
@mwhelan9411
@mwhelan9411 2 жыл бұрын
Me too.
@joespazio3965
@joespazio3965 2 жыл бұрын
Right !!!!
@ЛюдмилаИванькова-з6ъ
@ЛюдмилаИванькова-з6ъ 6 ай бұрын
Перевод
@goldenretriever1508
@goldenretriever1508 2 жыл бұрын
Not sure that the sealed bearings are designed to funtion with downward pressure being applied to their inter sides.
@umeida
@umeida 9 ай бұрын
Great idea! Will it work outside too? In snow and rain?
@arzie2000
@arzie2000 4 жыл бұрын
deep groove ball bearings are not meant for axial forces, you'll ruin the bearings in just a couple of days
@lamyellerie1367
@lamyellerie1367 3 жыл бұрын
What is? I'm looking for something very strong to slide a metal frame in... Not sure what to look for tbh
@adarshmishra7138
@adarshmishra7138 2 жыл бұрын
Brother ap ke jaisa hi very smart idea hai bahut sunder
@subz5819
@subz5819 5 жыл бұрын
Okay. So, where's the motor?
@ottoraul
@ottoraul 4 жыл бұрын
It's still in the hardware store. 🤣🤣🤣
@arshadbabu786
@arshadbabu786 2 жыл бұрын
good 👍👍👍..Thank you Messi 😀
@panik2475
@panik2475 5 жыл бұрын
What a tiny motor. Still unable to spot it..
@andreasfredy5560
@andreasfredy5560 4 жыл бұрын
He doesn't understand the meaning of "motorize" he wrote.
@b3arwithm3
@b3arwithm3 10 ай бұрын
Great idea. But how does it slide on the flat bar? The bearings are not contacting the side of the bar.
@DIYDomTheBuilder
@DIYDomTheBuilder 2 жыл бұрын
I like the design application, especially using opposite corners on square tubing as a “track”. Like many others, I too was disappointed that there is no portion about making it “motorized”. 🤨 Maybe retitle video as ‘Make An Awesome *Chassis For* A Motorized Slider’? …or just add ‘Part 1’ lol
@haitmtv3191
@haitmtv3191 3 жыл бұрын
I was planning to buy a slide but after watching this clip of yours, I gave up on that idea. Thank you for sharing
@brahimbellal9884
@brahimbellal9884 2 жыл бұрын
excellent travail, c'est exactement ce que je cherche pour ma machine combinée, qui sera proch sur youtube, merci chef!
@AJtheAutomobileEngineer
@AJtheAutomobileEngineer 5 жыл бұрын
I love you sir 😘😘😘 I am your big fan
@mrsunyofficial
@mrsunyofficial 5 жыл бұрын
thank you BROOOOOOO !
@AJtheAutomobileEngineer
@AJtheAutomobileEngineer 5 жыл бұрын
I am live in India You live in USA....? You are a big genius KZbinr
@bbmwmechanicalguru8537
@bbmwmechanicalguru8537 5 жыл бұрын
Love you sir
@thetruthcellar-channel1038
@thetruthcellar-channel1038 Жыл бұрын
I was looking for the exact parts list in the description below, but I couldn't find it? Any help would be appreciated. Thank you
@sebytro
@sebytro 3 жыл бұрын
Where exactly is the "motorized" part? And what is this used for?
@djpoolservice
@djpoolservice 7 ай бұрын
Awesome! This gives me some great inspiration
@illi426
@illi426 3 жыл бұрын
Good idea for example a sliding door
@stephenjohnson9202
@stephenjohnson9202 10 ай бұрын
is that one of those wish motors? wish you had one.
@How-I-Roll
@How-I-Roll Жыл бұрын
Great idea and video. Do you have a video with the motorized part of the design?
@TheBurnsStuff
@TheBurnsStuff 2 жыл бұрын
You could use V groove bearings instead for most of these. Where's the motorized part?
@frodo332
@frodo332 11 ай бұрын
Will this work for a round metal pipe too?
@aion2177
@aion2177 4 жыл бұрын
cool but it can't take much load since thouse bearings are supposed to be used vertically not at an angle. you need tapered bearings for propper load bearing.
@PP.EKOTECH
@PP.EKOTECH 3 жыл бұрын
GOOD JOOB !!! Regards PP.
@jellopoolparty7112
@jellopoolparty7112 2 жыл бұрын
looks like that may work on piping as well
@nathanscott1764
@nathanscott1764 5 жыл бұрын
Exactly where is the motorized part? Did I miss it or is it not even shown? If you are going to say it's motorized then show it!
@carlosfaria860
@carlosfaria860 5 жыл бұрын
kkkkkkkkkkkkkkkkkk. I think this is a joke !!
@carlthornton3076
@carlthornton3076 2 жыл бұрын
Very Good!... #301 ✝ {6-24-2022}
@creativeability
@creativeability 3 жыл бұрын
Good idea
@tth-coulid
@tth-coulid Ай бұрын
is there any way to do it without bearing?
@alexandercenteno1896
@alexandercenteno1896 Жыл бұрын
ME GUSTA LA IDEA,SENCILLA PARA ELIMINAR LA CREMALLERA DE PORTON ELECTRICO,Y ADAPTARLO AL PORTON DE GARAGE- CON GUAYAS.LAS CREMALLERA ESTAN CARAS+GRACIAS GRACIAS.Y BENDICIONES
@CanalSHAWBE
@CanalSHAWBE 5 жыл бұрын
Bom trabalho 👍👏
@breadeater5221
@breadeater5221 5 жыл бұрын
0:07 i have a bad feelling about this
@steveulrey4895
@steveulrey4895 3 жыл бұрын
That's exactly the time I left to read the comments. Thankfully yours was the 2nd one and I didn't waste more time finding someone to agree with.
@andyroa9904
@andyroa9904 Жыл бұрын
What ate the sizes of those bearings?
@OmbastarlyComedian-hd2gy
@OmbastarlyComedian-hd2gy 6 ай бұрын
Amazing I would like to use it on my project.
@ramijali6964
@ramijali6964 Жыл бұрын
Good❤
@odinata
@odinata 2 жыл бұрын
Umm....Where is the motor?
@Goinbig
@Goinbig 7 ай бұрын
Those bearing and not designed to be horizontally loaded. They should be vertical.
@jazminjjt6372
@jazminjjt6372 Жыл бұрын
Se puede usar invertido, para poner doble riel elevado .y soldado a los cochecitos , una base para carga?
@trisrrkarya9100
@trisrrkarya9100 2 жыл бұрын
Mantap bang salam dari pemula 👍
@nivedmurali8523
@nivedmurali8523 5 жыл бұрын
What Do you mean by "motorized"?
@usainiidris2640
@usainiidris2640 4 жыл бұрын
Good question
@zoecentenaje6860
@zoecentenaje6860 2 жыл бұрын
will it work on curve rail?
@DestraAmni
@DestraAmni 3 жыл бұрын
Kenapa baru sekarang saya tau.. nice
@lazee60
@lazee60 4 жыл бұрын
a genius slider, and with a leaner actuator, wow
@krudos6676
@krudos6676 Жыл бұрын
Thanks a lot being looking for exactly same slider technique for long. Simple and sweet technique
@rodolfovazquezroldan6905
@rodolfovazquezroldan6905 3 жыл бұрын
What is this for, colleague, what use will you give it?
@WelderPemalang
@WelderPemalang 4 жыл бұрын
Good, i like it👍👍👍👍
@94k.e
@94k.e 5 жыл бұрын
شكد فرحت من عرفت انك عربي ومبدع بالتوفيق
@ruatarengsicolneyrengsi8924
@ruatarengsicolneyrengsi8924 2 жыл бұрын
Ingenious idea with scope for a great many applications. Just great. Thanks for sharing.
@quynhmonsonloan3022
@quynhmonsonloan3022 3 жыл бұрын
👍👍👍👍👍👍👍👍👍👍 ok
@ArcanePath360
@ArcanePath360 7 ай бұрын
Instant mute
@Beyond_Right
@Beyond_Right 5 ай бұрын
Lmbo
@robeenvishal5528
@robeenvishal5528 3 жыл бұрын
I want to make a heavy sliding table for my small sawmill.is this method good?
@สมพงษ์ธีระคานนท์
@สมพงษ์ธีระคานนท์ 5 жыл бұрын
Use for what
@Diyallrounder
@Diyallrounder 2 жыл бұрын
Thank you so much.....
@frankcaccamo3568
@frankcaccamo3568 2 жыл бұрын
❤️ love 🏅🏅🏅🏆🏆🏆🏆🍺🍺🍺🍺🍺🇦🇺🇦🇺🇦🇺🇦🇺🇦🇺
@sunitadwarka347
@sunitadwarka347 22 күн бұрын
I have one experiment for making car to move on sliding ice. You imagine vahical tyres moving, now imagine sliding strip. Now think how we can connect it. Mean using sliding ice strip at the bottom of car but control by wheels, we will fix strip at the bottom of tyres to move car in ice. Movement of car tyres will slide the strip either of iron or wood. Keep speed of 20 or 40.km. to have better grip. Staring will give direction to left ,right. No change in car engine, same engine, same driving system ,every thing must in extra attachment below tyres. We can avoid many accident. Think in this direction. Jay bharat.
@sunitadwarka347
@sunitadwarka347 22 күн бұрын
Play with ball bearing, tyres will move ball bearing to push flat wood or iron for more grips on car.
@sunitadwarka347
@sunitadwarka347 22 күн бұрын
kzbin.info/www/bejne/Z5vUmmCcl6ibqMksi=QBQ94VZvSPEAng7j
@sunitadwarka347
@sunitadwarka347 22 күн бұрын
Wheels of car Wheels rotate the ball bearing. Question is if weight. Wood or iron will take weight and everything will get adjusted in ice. Jay bharat.
@Rkasmr2023
@Rkasmr2023 Жыл бұрын
Simple can make with U groove wheel
@jax7942
@jax7942 3 жыл бұрын
It was sympathetic to fixing the bearings, but my first tests yielded unexpected results: With the bearings, it became noticeable that the screw did not "close" completely perpendicular to a threaded rod, as if the rise of the thread had a slight effect. But maybe if I had looked with a better quality screw it would have been good. Or will this solution always bring a little "skew" to the bearing?
@bishopp14
@bishopp14 2 жыл бұрын
Maybe a finer thread count would help, or make it less noticeable? Or maybe a spring type lock washer. That would have the added benefit of keeping tings from vibrating loose over time. Not sure if either of those would help but I thought I'd share either way!
@phuongtienche139
@phuongtienche139 3 жыл бұрын
Chia sẽ hay hữu ích
@artystycznebudownictwo1229
@artystycznebudownictwo1229 5 жыл бұрын
Super 👌 Like 👍
@mrsunyofficial
@mrsunyofficial 5 жыл бұрын
thanks you my frend
@sonofaspine
@sonofaspine 3 жыл бұрын
Nice build, especially the motor lmao
@smartassist9700
@smartassist9700 Жыл бұрын
Do you have follow up videos? For completion? Website?
@getn_bit4363
@getn_bit4363 3 жыл бұрын
How much weight would this hold ?
@BspPlays9287
@BspPlays9287 3 жыл бұрын
I'm looking for a design to use on a chainsaw mill im going to build. I have some 12ft T beams I'm gonna use as rails for chainsaw rig to slide. It 1/4 inch thick and 2 1/2 wide on flat face. My idea so far is to buy some metal hole saws and make some washers. Two big one small with a 22mm hole to put a skateboard wheel bearing in. Might make a press fit and weld a keeper on the sides so bearing stays in.
@mecanizadosgrela7380
@mecanizadosgrela7380 4 жыл бұрын
Interesante sistema. En su opiniòn con cual perfil trabaja mejor la guìa?. saludos
@angbinhingbuhay6933
@angbinhingbuhay6933 4 жыл бұрын
Watching from philippines
@satishsahu6881
@satishsahu6881 2 жыл бұрын
Can any one tell me what is the type and specification of this roller bearing
@edinburghtumuran916
@edinburghtumuran916 3 жыл бұрын
Cool one! Awesome!
@andyMSH700
@andyMSH700 2 жыл бұрын
its rubbish as the nuts are touching the angle iron at places which is not shown in the video and nuts do not turn therefore a friction point. But then the video gets viewers and this i guess this is the real purpose of the video.
@เกษมศักดิ์ยศศรียา
@เกษมศักดิ์ยศศรียา 3 ай бұрын
Thank you
@rabahrabah4212
@rabahrabah4212 4 жыл бұрын
thanks my freind
@Texno_Login
@Texno_Login 5 жыл бұрын
Вряд ли эти подшипники выдержат нагрузку как радиально-упорные... Ну дело сделано😊😊
@AlejandroCastiblanco171
@AlejandroCastiblanco171 5 жыл бұрын
it is not support cnc
@АлександрКиселев-ш1ф
@АлександрКиселев-ш1ф 5 жыл бұрын
И что это изобретение нам дало??? Машинку которая ездит по металлу? Нужно не много доработать это изобретение и тогда возможно оно и пригодиться
@ClaudiuGhioc
@ClaudiuGhioc 4 жыл бұрын
Limba rusa nu este universala! Daca eu scriu in limba materna, tu intelegi ceva? Eu stiu si turca, tu stii? In turca iti zic "hai sictir"! Good luck cu asta! :)
@jerrysmay1951
@jerrysmay1951 4 жыл бұрын
You put .5 bore bearings on .375 bolt for an axle. How is that any kind of precision? Might as well use a skateboard on a 2x4.
@jtluttermoser
@jtluttermoser 4 жыл бұрын
That weird stare at the beginning is gonna be a no from me dawg
@x87alpha1
@x87alpha1 3 жыл бұрын
there is a lot of play for precise applications.
@pyrospeed2598
@pyrospeed2598 5 жыл бұрын
Nice Chanel greetings from the netherlands
@harbertmoore2663
@harbertmoore2663 Жыл бұрын
What size are the bearings?
@charlesingram7022
@charlesingram7022 4 жыл бұрын
How long is bolts that that the nuts screw onto?
@HeinzSchumacher
@HeinzSchumacher 5 жыл бұрын
Drei Doppelrollen im Dreieck angeordnet von denen eine verstellbar ist funktionieren am besten.
@trishuljain8648
@trishuljain8648 3 жыл бұрын
Wow, great idea!.. 👏
@mecanizadosgrela7380
@mecanizadosgrela7380 4 жыл бұрын
Interesante sistema. Según opinión con cual perfil trabaja trabaja mejor el deslisador?, queda sin juego una vez ajustado?, saludos.
@AdiLas-my3xb
@AdiLas-my3xb 8 ай бұрын
Mantap bos ku
@حمزةحمزة-م4ف4ض
@حمزةحمزة-م4ف4ض 5 жыл бұрын
Cool work sir 👍👏
@baljeetsewah3171
@baljeetsewah3171 5 жыл бұрын
Samaz aya kya banaya isna
@HEMANTSINGH-zm8gr
@HEMANTSINGH-zm8gr 5 жыл бұрын
Nice video
@nurasiahjamilah5771
@nurasiahjamilah5771 2 жыл бұрын
Is the best
@saminarafique3722
@saminarafique3722 11 ай бұрын
Motorized??? with no motor.
@koitorob
@koitorob 9 ай бұрын
That's a great way to destroy a set of bearings! They aren't designed to take force in that direction!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!
@AutomotiveCNC
@AutomotiveCNC 10 ай бұрын
Good for misleading clickbait video, bad for actual usage. Both, the screws and the metal plate will bend quite easily under load. The bolt connections will slide along the channels, too. I know it from own experience, because I have tried that flawed approach when I was kid in the 90's.
@OumarHassan-Guedet
@OumarHassan-Guedet 10 ай бұрын
For the view of mechanical engineering you’re right. Can you provide an idea from your experience that you had?
@parihinchin9226
@parihinchin9226 4 жыл бұрын
Good job
@jairogomezmarin928
@jairogomezmarin928 5 жыл бұрын
Excelente gracias por compartir tus conocimientos saludos cordiales desde Cali Colombia 🇦🇲✌️
@davidstevenzuletamuriel4919
@davidstevenzuletamuriel4919 3 жыл бұрын
Aunque en realidad asi no se deberían usar esos rodamientos y menos para portones, tendría que ir a cambiarlos por garantía en unos pocos dias, estarían funcionado mal bajo peso.
@thelazycat_
@thelazycat_ 3 жыл бұрын
Where is the motorized part? Clickbait
@alabenchana8298
@alabenchana8298 5 жыл бұрын
Wow you made it to do only that 🤔
@oliverkauper6015
@oliverkauper6015 5 жыл бұрын
Interesting design and reminds me of cnc tables. Just makes me want to make a cnc table for my everlast welder even more now.
@losmejoresproductospromoci7728
@losmejoresproductospromoci7728 3 жыл бұрын
Muy buena la idea pero al colocarle peso se abrirían las balineras venciendo los tornillos.
@ynnmeditationandrelaxation5992
@ynnmeditationandrelaxation5992 3 жыл бұрын
couldnt find where is the motorized thingy in there
@BLAUEREITER68
@BLAUEREITER68 9 ай бұрын
Messi, is that you?
@nsk6914
@nsk6914 4 жыл бұрын
Eda mownee poli sadhnm❤👍
New Brilliant DIY IDEAS !
16:22
Mr Novruz
Рет қаралды 538 М.
Support each other🤝
00:31
ISSEI / いっせい
Рет қаралды 81 МЛН
Мясо вегана? 🧐 @Whatthefshow
01:01
История одного вокалиста
Рет қаралды 7 МЛН
Chain Game Strong ⛓️
00:21
Anwar Jibawi
Рет қаралды 41 МЛН
An idea that millions of people will appreciate!
8:04
MA-SH
Рет қаралды 9 МЛН
ALAT PENGANGKAT FUNGSIONAL || Tukang wajib mempunyai alat ini !! diy
19:21
special hanging wheels for sliding doors
7:06
WELDER TASIK
Рет қаралды 6 МЛН
Not everyone knows about this amazing device!
5:17
MA-SH
Рет қаралды 606 М.
Homemade An Awesome Tool Without Welding That I Didn't Know Before
13:57
2 Cool Ideas ! You May Need This !
7:19
Mr Tool Junction
Рет қаралды 4,7 МЛН
This idea will be appreciated by millions of people!
8:39
MA-SH
Рет қаралды 3,2 МЛН
Insanely Simple DIY Ideas That Solve Big Problems
8:04
Mr SunY
Рет қаралды 319 М.