Make automatic ON OFF room emergency Led light, diy idea

[@Thribularity]

I love it despite the possible flaws. I made a water alarm twenty years ago that was simple like this. My mentor called it a hungry circuit, but ten years later it still worked and on the same battery. This circuit is easy, simple and works. I am going to build one.

[@ABTabi]

Thank you very much dear friend ,,,,,,,,,,,,,,,,,,,,,,

[@rsubram24]

Initial connections with transistor, resistor and LED are ok, thereafter wire connections are not at all clear. You could have make it better.

[@berndn3056]

Das Löten hat der Verfasser des Videos nicht erfunden. The author of the video did not invent soldering.

[@djblackarrow]

The transistor in the schematic is incorrectly drawn. The base is always drawn sideways in the middle. Collector and emitter are always drawn at an angle. The emitter always has an arrow. For an NPN type it points outwards, for a PNP type it points inwards. Your arrow points in the wrong direction. So a bungling the wires just to twist and wrap with some tape ... That's probably the worst way to show something to others! Show it directly the right way, or let it be. Use Wago clamps with the designation 221-413 and put this connection into a junction box.

[@ABTabi]

OK, Dear friend thank you for advise and interest,,,,,,

[@rsubram24]

Your circuit diagram doesn’t show with main AC bulb connections.

[@blg53]

A very useful lesson in how not to solder.

[@prateek.lootingsonuz144]

Hello sir, Can I use 1k resister??

[@thegiruinternational1475]

can i use bt136 plz ans. me i have to make dis... 🙏🙏🙏🙏

[@ABTabi]

Yes ,,,,, Thank you dear friend for interest ,,,,,

[@jasondubas1161]

Sir autocharge and auto cutoff if the batery is full,

[@hamedbaghaffar2694]

Transistor not correct

[@chunksmedia7049]

Thanks bro.its very use full and easy steps

[@davidblackburn9640]

I like the clear plastic tape, you can see what is taped. Not everyone has just the right items available.

[@ABTabi]

Dear, you can an other thing like heat shrink tube or wire sleep.

[@mdshehraj1777]

Resistance is too hot bro in few seconds Why? Plese reply me bro!

[@colloidalsilverwater15ppm88]

Battery plus connected to base? Cutting wires with scissors? Transparent tape to insulate 230Volts? Aluminium heatsink? Collector from base? Dislike big as a house!

[@korkodel2495]

Asa este. Ai sesizat bine dispunerea pinilor. Baza in locul Colectorului.

[@Thribularity]

NPN transistor, forward bias closes the switch. Collector Is neg. I think he is ok.

[@matataullah]

Jeffrey Hemmerdinger sameer

[@pedroventuracarlos7066]

hola tambien se podra con el BD135, y otra pregunta..... me podrian decir si al dejarlo enchufado el cargador perenne a los 220v la bateria no recalentara o automaticamente se pone en off porfavor digame. gracias

[@ABTabi]

Dear friend you can use bd135,,,,,, not auto cut charging ,,,,,, but wait....... i will make as soon as possible ,,,,,, Thank you for interest ,,,,,,

[@pedroventuracarlos7066]

OK, thank you very much friend,

[@Thribularity]

Can the 3.6 v battery be overcharged? USB is 5.5. Did you add a resistor?

[@ABTabi]

Thank's dear friend,,,,, you can use this circuit and protect the battery from over charging ,,,,, Please watch this project kzbin.info/www/bejne/aHOmiJWNjLqoj6s ,,,,,,,,,,

[@StevenCookFX]

That soldering iron is bad. Its one of those cheap ones that the tips just disintegrate. Get a decent one. Weller, Hako etc.. Also you need to use heat sink on those silicon components so it takes the heat away. Especially with a over heated iron.

[@ABTabi]

OK, dear ..... Thank's

[@djblackarrow]

I use an "Ersa" soldering Iron. In addition, I have a sponge that I moisten for soldering always to be able to clean the soldering tip regularly.

[@villagerboy5120]

What i can use 12v batter on 5v battery

[@mehdisoleimanian6394]

Hello, dear friend, young engineer, I hope you are well, your programs are beautiful and informative, thank you, but please leave his plans so that we can make them too.

[@ABTabi]

How can I help you?

[@faustominuzzo4289]

Grazie AB Tabi, ripresa filmato ottimo, descrizione materiali e caratteristiche volte, utilissime, Ti regalo il mio like, e.. mi iscrivo al tuo canale. Ciao, Fausto (Roma, Italia)

[@ABTabi]

Thank you very much my dear friend,,,,,,,,,,,,,,, I hope you always with me,,,,,,,,,,,,,,,

[@Hindu-Vlog760]

Kitne bolts ki battery se chalayenge

[@ABTabi]

4 volt battery, Thank you dear friend for interest ,,,,,,,

[@kan815k]

How long is battery time? What the maximum or minimum LED we can use?

[@ABTabi]

calculate with transistor watt and led

[@Semar-sr3iv]

Hello sir, can I change another transistor. Thank you..

[@NitishKumar-uf4ux]

I can use BD139 at the place of BD136 transiter Please reply me

[@ABTabi]

If you know about NPN and PNP ,,,,,,,,,

[@NitishKumar-uf4ux]

@@ABTabi recently I study about PNP and npn transistor

[@radiorexandy]

Next time, use heat shrink tubing rather than plastic tape. Really?

[@aniqkhan9108]

Lol we wrap shoppers to save money 💰 and u r saying rap. Rubbers

[@KentuckyDogg]

Hadji and Habib Electrical contractors have nothing but the most current supplies and workshop tools available in their shop.....Let them give you a quote on your next big electrical install.....Call Now ! 888-PUSH-START

[@techengin8949]

well done bro i like your method of electriction

[@ABTabi]

I'm glad you like it

[@asangamendis6105]

Thanks, Can we apply a booster to the battery & connect 12v led strip, if so does battery charge, Can we apply 12v battery &12v stripe for same curcuit 🤔

[@ABTabi]

You can try ,,,,,,,

[@إبراهيممحمد-م1ث8ل]

nice..thanks...plz..does the battery..recharge in this circuit?

[@ABTabi]

Yes, auto recharge by charger ,,,,,,, Thank you dear friend for interest ,,,,,

[@spacial2]

I am a little concerned with the 5V being applied to the batterys. With some adaptation to the LED bank, a 5V rechargeable could be used making the circuit non-maintaining. Very handy.

[@mdjalaluddinprodhan6140]

জিনিসটা খুবই সুন্দর। কিন্ত কি ভিডিও করলেন ? কানেকসন গুলো কোথা হতে কোথা নিলেন ঠিকমত বোঝা গেলোনা। ভাল করে ভিডিও করে আবার দেন। যাহোক পরে বুঝছি। ধন্যবাদ।

[@Дед34]

По технике: Не мешало б объяснить принцип работы. По технологии: Руки бы оторвать "мастеру". Technique: Explain the principle of operation. Technology: Hands to tear off the "master".

[@renumisra]

be 136 k saath to 4mm led k +m add krna h nd mobile charge ki plate bhi lgaa skte h kiya

[@baala2739]

can you pls make it with auto on / off using relay + tp4056 module + brightness controller

[@howardludwig9715]

OMG What a hack job.

[@Nadeem-i9t]

Which wire where not showing in good ..

[@TAMILTRUEWORDS]

Transistor center is base you mentioned collecter ? Why

[@kennethcoutinho4439]

Is the circuit diagram CORRECT BD 136 IS A PNP TRANSISTOR

[@msk965]

Bro when we switch OFF Light ( other than power failure) than also emegency LED will be ON.

[@ABTabi]

Yes, dear friend,,,,,,,,,,

[@jamilahmedahmed9315]

oleg hlp me im soore

[@durgaprasadbehera111]

No emergency light will not be on. It will be on only when there is a power failure

[@911Privacy]

good job . Do not worry about the frustrated . 🕺

[@ABTabi]

Thank you very much my dear friend,,,,,,,,,,

[@daveseddon5227]

Transistor at 5:26 marked incorrectly - e is ok. c should be b & b should be c.

[@vorotyn1977]

Запитывать адаптер нужно до выключателя и будет аварийное дежурное освещение при пропадании сетевого напряжения. Спасибо за идею.

[@ABTabi]

Thank you very much dear.

[@rsubram24]

Good thing is showed list of components for the project. Very bad presentation, not able to understand anything, not a systematic way of communicating things.

[@balkrishnapal1682]

Ager esko direct Ac se connect krenge to bulb bnd ho jayega or jese power cut hoga bulb on ho jayega but ager ye aise hi charger ke sath Ac se connect rhega to kya battry or charger pr eska koi effect nhi hoga because charger jb tk AC power on rhega tb tk battry me charger se current aata rhega to fir kya jyda charge hone pr battry fat jayegi kya hoga ya battry pr esko AC power on hone pr koi effect nhi hoga ...??

[@mrelectronicslab799]

Koi bhi PNP transistor se ho sakta hai kya

[@ABTabi]

Yes ,,,,,

[@subhahan8706]

sir can i use bc 547 transistor please give reply sir

[@ABTabi]

Dear friend you can use ,,,,, but this is best ,,,,,, Thank you for interest ,,,,,

[@alwincecil4887]

Sir 6v 4.5ah battery ke saath 5050 24led plate ka emergency circuit banake bhejiye please.

[@mariokaram9114]

Can battery be overloaded ? And how to connect auto cut-off battery charger to this circuit?

[@akhileshkumar-pp7df]

Sir yah sare diod nahin mil pate aap batayen kahan se khariden main budaun

[@ABTabi]

Search online ,,,,,, or use equal ,,,,,,

[@pranjyotideori8410]

Waw Amazing Connection

[@anandsagar7598]

If i want to switch off the led but at the same time battery is charging,then how can i do??

[@hendrapermana7627]

it can be stopped by both bosses ... the problem is if you use the room if noon the lights are turned off ... if you can't die both the lights on the day continues ... love energy ... thanks

[@JoseSilveira-newhandleforYT]

I really enjoyed the collector coming out of the base of the BD136. The circuit works but transistor representation is misleading. Not a bad idea, but poorly implemented and presented. The 5V power supply connects to the battery via a diode only. To charge a lithium cell you need a charge controller, particularly if the charger is permanently connected to a standby battery.

[@francisco9427]

Legal 👏 Deus te abençoe sempre

[@ABTabi]

Thank you very much dear friend, God bless you

[@user_Alien_89]

увидев изоляцию 220в СКОТЧЕМ, у меня чуть глаза не вытекли

[@ABTabi]

O oooooooo,,,,,,,,

[@decimal4334]

вот вы доебались до скотча," я его слепила из того, что было" ну нет у чувака нормальных материалов, чож теперь ему обосраться штоли? главное идею показал. а так в индии жопа видать с комплектующими.

[@ABTabi]

These components are not in other country like IN.

[@ПетрКононир]

@@decimal4334 Когти обрезать и паяльник почистить

[@joshitoshi9835]

How can we add photo diode to detect available light in the room so that when there is no enough light available in the room and electricity breakdown occurs than it should turn on light but if enough light is available like in day time than it should not turn on the light.

[@vinodchaugule3415]

Resistant is so hot in sum second please shwo video .. and how too connect charging indigeter

[@northeastworld5221]

Conseser k name ti bata

[@littlepoison9632]

Крайне не советую использовать эту схему, если не хотите подпалить своё жилище взорвавшимся аккумулятором.

[@rupeshsable2952]

Sir batry over charge to nahi hogi na plz reply

[@mistershyam8237]

may I do this with 12 volt DC battery. what things does required , explain me. I.e. MOSFET, resistor, food etc, waiting for your feedback

[@ABTabi]

Thank you my dear friend, if you wan't to make 12 volt auto on off circuit please watch this project,,,,,, kzbin.info/www/bejne/gZWndKmBrsyZeLs

[@dkyadav8973]

CAN THIS PROJECT DONE WITH BT136 TRAIC. AUR KYA ISKE RESISTOR KI VALUE C CHANGE KI JA SHAKTI HAI KYA

[@ABTabi]

BT136 not working with low dc voltage,,,,,,,, and try to change value ,,,,,,,,,,,, Thank you dear friend for interest,,,,,,,,,,,

[@FullrangeHZinAction]

+ABTabi ,it's ok for batery - 5 volt insted - 4,2 maximum posible in charging safety mode? will batery work good? will not it fired or something, please dear friend tell me...?

[@KlaarToet]

Dit is “plakken”. TIP: Deze “soldeerverbindingen” zijn niet betrouwbaar. A.u.b. soldeertin gebruiken en beide delen die aan verbonden moeten worden eerst van tin voorzien. Gewoon in elkaar draaien met een stukje plakband eromheen is al helemaal niet betrouwbaar.

[@ABTabi]

My dear, when we make circuit with PCB board when every thing reliable like soldering and components etc. But people can not understand easily, so we make open circuit. Thank's

[@vijayparit9694]

उत्तम चाजिॆगबल्ब ची रीपेअरिसांगा.

[@MedSou]

*Very helpful,Thank you* ❤❤❤

[@ABTabi]

You welcome dear friend,,,,,,,,,,,,,,

[@munnisonwani951]

Bhai uska macin know sa ka hai Ohms

[@prakashpaul4992]

Good,very nice dear.

[@ABTabi]

Thank you very much dear friend,,,,,,,,,,,,

[@SANDEEPKUMAR-tm3rf]

क्या इस सर्किट से बैटरी भी चार्ज होगी

[@SANDEEPKUMAR-tm3rf]

Kya circuits DC battery charge Hogi Jo isme connect hai

[@ABTabi]

Yes,battery charge hogi.

[@frankbataitis5701]

Nice

[@vayrabbiswas9434]

cherger ke _ + regtens 2 side mai lag raha to regtens khrab ho jiaga to vi a kay ha

[@cfrajan2540]

vayrab biswas by

[@azeemehsan8482]

How it is working without any supply... r energy

[@kalicharan7239]

VERY NICE

[@ABTabi]

Thank you friend ,,,,,,,,,

[@kenklassen4317]

Fun if you like going to the work of making stuff. I do too but not an electrician. Leds I like because they only have 2 wires and nothing happens if you hook it up backwards. 3 wires messes me up. So I payed 1.25 $ for a solar garden light and put it in the rooms i wanted emergency lites. If the power goes out the lites come on. And they look better. No disrespect.Just saying. I'm a carpenter and if I showed someone how to build cupboards and with all of the tools and knowledge they need, I would this k most wood just go buy them As well. Good job tho, I think.

[@Julio-Cesar777]

Es bueno pero está voz n poco confuso ya que no pasas completo al momento de conectar!!! Se piensa que son dos interruptores diferentes !!!!

[@MrRaj98321]

Which type of this transistor BD136 NPN or PNP ?????

[@ABTabi]

PNP ,,,,,,,,,, Thank you dear friend for interest,,,,,,,,,,,,

[@MrRaj98321]

@@ABTabi thank you bro.

[@saipuvvala3413]

Bro Kani sleeping time lo manaki light avasarame ledu kada Mari appudu stop cheyyadam Ela?

[@ramgoud4092]

How to auto cutoff over charge in this~??

[@indrakshidigital636]

12 volt ki led strip use karne k Lia , parts ma kya kya change karna padega ?

[@parimalmaji8449]

Circuit can run 1.5 volt?

[@ABTabi]

No, if you have 1.5 volt led lights then working ,,,,, Thank you dear friend for interest ,,,,,

[@Sri-lt3vq]

Pls ac la work agum podhu.... Bettary ku charge erudhanu multimeter laa check pannirulalam

[@techranajivlog1720]

Bhai idea to sahi hai but light jane ke bad charger ko input kaise denge...

[@ngothihanhngo7692]

can i use 13003?

[@ABTabi]

Dear friend you can use ,,,,,, Thank you for interest ,,,,,,

[@thePurushTube]

@@ABTabi 13003 is NPN. you used different type. Infact Both types npns as well as npn can be used if the polaities are taken in to consideration. This video needs a revision by resubmitting the diagram and ading notes for substitution NPN transistors too

[@safdarali4285]

such as great vedio...I waiting for this vedio.. thanks for uploading.

[@wolfgangheisig4622]

>>> ELEKTRONIK FREUNDE ++ MODELLBAU *ALARM* WERBUNG* SICHERHEIT* ++ R E S T P O S T E N * MODULE** BAUSÄTZE ++ LED EFFEKTE MONO L I C H T S C H R A N K E N USW: ICH FINDE JEDEN F E H L E R IN 10 MINUETN

[@deodattajoshi323]

There are so many videos I have seen regarding this but I like your video because it finds me useful and near to my idea.I have mail you on your mail please see...

[@deodattajoshi323]

please see my mail

[@abhilashyt7115]

Power on it charges the battery when power goes off it turns on the light good idea like emergency inverter turns on. Good

[@ABTabi]

Thank you very much dear friend,,,,,,,,,,,,,,

[@sujeetcreationyt6090]

Bhai Light to bana diye par yeh to rat ke liye h par jab badi wali light band karenge tab din me bhi woh barne lage ga isko din me kese band kare nge

[@akashsingha234]

When I use 6volt battery then how the adapter need.

[@akashsingha234]

I mean what type of adapter

[@ABTabi]

depend on your battery amp ,,,,,,,,,,,,,, Thank you dear friend for interest ,,,,,,,,,,,

[@akashsingha234]

ABTabi if I use 5Ah battery.then what should I do?

[@ABTabi]

300 to 1000 mAh ,,,,,,,,,,,,,

[@anycall12]

can we use bd 139?

[@ABTabi]

No, only PNP transistor like BD140, BD786, BD138 etc. Thank you dear friend for interest in my automatic ON OFF light project.

[@manoharwarti45]

BinA ldr yuj kiye bana doya on oof sarkit sab jhut fek hai bina ldr ka koi bhi nahi bana sakta hai on of sarkit 😂😂😂😂😂😂😂😂😂😂😂jara hamko bhi to batao kese banaye bina ldr ka😂😂😂😂😂😂

[@munnisonwani951]

330 Ohms know sa macin ka hai video banana

[@munnisonwani951]

Kya huaa bhai video kyo nahi banay

[@chunksmedia7049]

Battery will charging or not?

[@ABTabi]

Yes, Thank you dear friend for interest ,,,,,,,,,

[@Rajeshvaika]

good video man, keep it up

[@sustainableforestmanagemen6714]

Please remove dirt from the solder tip otherwise .. such a vomiting condition by looking at it.

[@mukeshkumarsihmukeshkumars3539]

Bhai mast hai

[@ABTabi]

Thank you dear friend for interest ,,,,

[@thomasandrews7255]

Plz list some alternatives for bd136

[@ABTabi]

BD138, BD140, BD786, BD176, BD166, Bd376, BD227, BD234, BD438,,,,,,, Thank you dear friend for interest in my electronics projects,,,,,,,,

[@amitkumarvishwakarma9605]

Sir ye jo belnakar hai ye kya hai

[@anuroopdinkar]

Sir i have a question from you please provide me the information about a dc fan that run by DC54V and 10W . So how can i manage current

[@sumitsainiharpal6323]

h

[@gavinminion8515]

WAHAYYY! He sticky tapes the mains wires after twiisting them together and I'm out!

[@ABTabi]

My dear, i am making Temporary circuit for teaching.

[@spacial2]

@@ABTabi Really should be using insulated connector blocks sir. Covered with proper electrical insulating tape, before applying mains power. Just saying. I do appreciate your videos.

[@michaelkarger7175]

@@ABTabi If you want to teach, teach correct manners/building. Even if temporary you could use e.g. luster terminals. Teaching also means explanation but all i heard was annoying music. At 08:00 you are no model at all, by touching the energised 230V area (especially because of this crappy "insulation"). Thumbs down!

[@charlielennon5411]

Electrical engineer - Level 0.

[@carlosmolina8835]

Colombia mil gracias por su información por compartir sus conocimientos escuchar opiniones profesionales éxitos amigos

[@ABTabi]

Thank you my dear friend.

[@Smartunboxp]

Watch our channel also for this type video

[@harrylanza]

Had to stop watching right after the clear boxing tape and come read the comments.

[@garbojad7056]

Ale druciarska robota

[@jimparsons6803]

Pretty clever.

[@edifierbass7821]

Yes its working but the Battery charger is not good , make it automatic charger