Make This ● To Suck the Oil From Any Engine !

NO more Mess!! This is the simplest mess free DIY way to change your own car engine oil, rototiller oil, ride-on lawnmower oil, jet ski oil, scooter oil, motorcycle oil, pressure washer oil, inboard outboard motor oil or ATV oil. Great for changing the oil in anything that is hard to drain. Most lawnmowers today have no drain plug. Uses are endless. Super cheap to make and saves you money. Also makes a great fluid extractor for power steering fluid, brake fluid and transmission fluid.
NOTE: NEVER USE THIS TO SUCK UP GASOLINE !
●Mason Jar Oil Sucker .... • LAWNMOWER OIL Change ●...
●Shop Vac Oil Sucker .... • LAWNMOWER OIL CHANGE ●...
USA
● Vacuum Pressure Gauge .... amzn.to/3TWSvKr
● My Great Little Cordless Drill .... amzn.to/3cYzjeP
CANADA
● Vacuum Pressure Gauge .... amzn.to/3L1ARB6
or MY STORE
● www.amazon.com...
● www.amazon.ca/...
PARTS:
1.5" waste cap and fitting
4" to 1.5" reducer
4" pipe
4" end cap
9 ft. 1/4" OD fridge hose
1 ft. 1/4" fuel hose
Full Transparency! A small portion of each sale goes from Amazon's pocket to my pocket with no additional cost to you! Thanks for your support. It's very much appreciated!
Coconuts by MBB / mbbofficial
Creative Commons - Attribution-ShareAlike 3.0 Unported - CC BY-SA 3.0
Free Download / Stream: bit.ly/2vear96
Music promoted by Audio Library • Coconuts - MBB (No Cop...

[@luthead]

I love that you’re straight to the point , clear and concise. No BS , or rambling on about gibberish.

[@chrisnotap]

I try to do that in all my videos! Thanks for that great feedback!

[@nefariousyawn]

That little trick to make a barb on the clear tube was pretty clever.

[@paul_desjardins]

Perfect Chris, if one is worried about having half a cup of dirty oil left in the engine, you can add some clean oil and suck it up along with the dirty one until it looks clean.

[@chuckhall5347]

What a great project! Transmission pans typically have no drain plug so it is always a huge mess to change transmission fluid. This is a game changer for transmission service.

[@chrisnotap]

Also good for flushing power steering fluid and sucking brake fluid from master cylinders.

[@Tsuter1978]

Extractors work great for this. I have a large Pela model that will hold over 10 quarts. I believe it’s a 15L model. But plenty of room to do a transmission fluid replacement

[@jean-clauderainville677]

Hey Chris, absolutely brilliant work! As the "vacuum pump" is actually a fridge compressor, it has its own oil inside that must be kept otherwise the unit will fail... that compressor oil produces microdroplets that go out the air exhaust port. I would suggest you add an "oil trap" at the exhaust to capture the oil that will then trickle back in the compressor. I personnally use steel wool or a polyethylene fiber bundle inside some odd transparent container. Be careful of the type of pipe you use to joint it to the exhaust as compressor oil is often a very light ester based lubricant (not exactly "oil" per se) that will leak through most pressure-fit joints. Messy .... Cheers! Edit: the oil trap will also catch compressor oil in case the "thingy" accidentally falls on its side... you never know... ;]

[@WhiteOak09]

I was wondering about that because I've fooled around with one out of a dehumidifier and it blowed that stinky oil all over my basement on to me and my son but how much oil do they hold and can you put in to much and where can you get this type of oil , thanks.

[@jean-clauderainville677]

@@WhiteOak09 If I remember correctly you can find it on the 'net, check out "compressor oil" but in my experience, even a lighter sewing oil type fluid works. It has to be light and not hygroscopic since pulling humidity from the air will rust the compressor components. For the "trap", I used plastic water bottles at first but if the exhaust gets warm, it gets messy. Better use something that is a bit sturdier since it has to hold itself at the top of the exhaust pipe...and that pipe must go directly down in the compressor, don't leave loops that can trap fluid...and blow it all-over the place. Edit: if you plan on pumping humid air or steamy gases, you need tu put a cold trap *before* the compressor as any vapor will condense below the oil and rust the components. It will simply stop running if it seizes.

[@chrisnotap]

Correct. I pointed the exhaust pipe upwards and the oil seems to stay in the pipe and not come out and it trickles back into the pump. Yes eventually it will fail but it can take quite a long amount of running time for this to happen.

[@jean-clauderainville677]

@@chrisnotap It's mostly the smell and oil mist that bothers me 🤢 I run my 1500watt unit for hours to circulate an electrolytic solution trough a filter and as the wretched thing reaches 55°C, the vapors in the lab are horrible. The trap reduces that to almost nothing. Now, if I could only reduce the noise and vibration all would be dandy... ;]

[@WhiteOak09]

@@jean-clauderainville677 thanks alot for your help 🙏.

[@RichardFreeberg]

Nice project! I really appreciate the straight talk and clear presentation. None of the usual YT horrible music, posing and unnecessary verbiage. Don't know if I'd ever do this myself, but it's interesting. Thanks!

[@IFKY]

My guy if there's anyone that deserves over a MILLION subscribers it's you..

[@chrisnotap]

Wow! Thanks so much for that!!

[@shanequinn8356]

Hi Chris, absolutely brilliant how you cover every little thing. My preference is to drain hot as oil holds particles in suspension up to 28 micron as all oils filters are that grade. The quicker oil gushes out the more of the particles flow out with it. This speeds the pump out flow but that heat may allow the tube to bend again and not remain at the bottom🤔 What's REALLY great about your suction drain is not lifting the car, or scraping front moulding as you drive on the ramps, most of all not having to remove the big engine undercover. This arduous task is required to swap the oil filter on many engines though. Thanks again.

[@WhiteOak09]

I absolutely love your videos and my son was about 8 or 9 years old and he's the one who was watching your videos and turned me on to your work and Project Farm 🚜, you really truly have awesome content , Thanks a bushel 👍.

[@gregorymacneil2836]

I think it is a wonderful project but I purchased a Mityvac Fluid Extractor for $100 that handles all my oil extraction needs. It worked straight out of the box. I am not sure based on today’s prices that the parts required to build an extractor are much less than the Mityvac. That said I do love your project.

[@benjaminreinhardt259]

I like it. I pulled the compressor out of a dehumidifier a few months back with no project in mind, just stuck it on a shelf. I think I'll have to make one of these. I have a steel tank I'll likely use though, wife gets helium tanks for the kids birthday parties and I have a few of them kicking around. Thanks for the idea!

[@mizukamendoza7250]

can I use a old dehumidifier compression that no longer works or does it have to be a working compressor?

[@briantayes2418]

This is awesome. So much attention to detail to make a hassle free tool. Subbed!

[@MScott-y4g]

Great idea sure would save a bunch of messes, always hated dropping a transmission pan full of oil.

[@thisislilraskal]

Chris, you think of everything. Impressive.

[@okkrom]

Your channel is underrated. Love your videos!

[@chrisnotap]

I appreciate that!

[@NicoSmets]

Very interesting. This reduces an oil change to a very minor task.

[@zenMermaiden]

a thoughtful design, every detail attended to. thank you

[@chrisnotap]

Glad you like it!

[@mrobvious1100]

Sir, that was in genius. I am curious. Could you give me an idea on how to use the shopVac without getting oil inside. I did see a video where someone took half. A soda bottle and drilled a hole in the middle of the cap and put it in the hole where the shop vac hose goes and fed the tube through it into a container within a container and turn the shop vac on.

[@dbanka471]

Excellent- been think about buying a vacuum pump to change the oil on my jet-ski…..i have almost all the component except the compressor …thank you for the very instructive and practical video…so glad found this channel

[@dchall8]

I realize it's been a year since you posted, but you should be able to find an used dorm sized refrigerator in or near a dumpster at any university that has dorms or nearby apartments. Wait until the end of the semester to find what you want.

[@allenrusselljr]

​@@dchall8that's a great tip. I live across the street from a large SUNY (new York) college and at the end of every semester we all go dumpster diving. I've pulled laptops, tablets, Dyson vacuums, one year over 400 tide pods, a 1/4 pound bag of pot and a dozen bottles of antibiotics out. I have a neighbor who only gets mini fridges. He usually finds 15-20 and he tests, then resells them. It's astonishing to see what the college "kids" toss.

[@TheHansoost]

Not what I need at present as my 2009 vehicle's fluids can be drained fairly easily via gravity. However, many newer cars lack this "old tech" and want to force you to the dealer. I really like the idea and will keep it in mind. Really good, clear, concise video. Thanks.

[@petehayward7478]

Excellent idea. I’ve always used a manual pump to drain my cars oil and it’s a pain and very slow. This looks perfect.

[@mgreen6548]

Now I know what to make for Dad’s Christmas present. Great stuff!!!

[@sekaf4125]

I must say this is some of the very best detailed instructions Ive ever seen. Im making one thank you!!!

[@chrisnotap]

Wow, thank you!

[@victoryfirst2878]

They say great minds think alike. I used the same method for vacuum as you did sir. One thing else, I would use the vacuum to suck out every little bit of oil left in the pan. This is where the most contaminated stuff is located in the oil Chirs.

[@rmatthews5172]

Awesome idea! The best part is NOT having some guy stripping your oil pan bolt👍 The down side of it, you still have to change your own filter🤔.

[@dchall8]

I used to be in the jet engine business in the USAF, and learned a bit about oil systems as part of the job. The AF uses only synthetic oils, and they test them periodically to see if they have become contaminated. If the oil is contaminated beyond a certain limit they like to filter the metals out of the oil and reuse it (because it is synthetic). I think you can get away with reusing the same filter for 1 or 2 oil changes and take it to an oil change place (or DIY) every 3rd time. For me that would save $150 per vehicle.

[@mbehring9042]

Good timing Chris, was just researching how to do a 'topside' oil change of my car.

[@CheaddakerT.Snodgrass]

Nice job! I was thinking I bet you could modify this with some other tubes to make it self emptying as well. So you could pump right into the oil container you just used to fill the car.

[@harrypitts7389]

Bucket list project

[@scottboettcher]

When I bought my old Ford truck, the owner had put in a 427 stroker motor. The issue is that the oil pan drain plug is above a cross member, making oil changes a royal pain. He purchased a commercial unit very similar to your design (but I like yours way better). The issue is that not all oil pans have clear entry to the bottom from the dipstick hole. I reckon I got 85% of the old oil out this way, and while it's probably good enough - as long as I change it often - I don't like that it isn't all new oil. I most likely will get a drain plug that has a fitting on the end to route around the frame, and use that along with the pump. We used a small home compressor, and it did take a long time, as well as the issue we had placing the tube in "just the right spot" to get as much as we could. Thanks for a great video. This one gets two 👍🏼👍🏼

[@lyndonfring6421]

A few suggestions. Sight glass or transparent/ translucent oil sump that would show level of oil sucked out would be good. You could also have a u-tipped hose that you could insert via the oil pan plug to suck out the gunk, metal shavings, crud or whatever on the bottom of the oil pan that is lower than the plug. Thanks.

[@kenmeyer5930]

Awesome as usual. Does anyone remember Rube Goldberg? 😀And i only mean this in the most complementary, positive way! Thank you for sharing your creativity with those of us that have trouble changing a lightbulb!

[@chrisnotap]

Rube Goldberg is the best! Such creativity!

[@danamoose1234]

So many great tips in this video! Thanks for sharing!

[@butler386]

Excellent idea and project. I bet this would work for cleaning out air condition drain lines as well with proper size ends. Thanks for the videos. Gonna have to go back and look at some of the others.

[@paullarouche4648]

Another beautifully produced video about a brilliant idea from Chris.

[@chrisnotap]

Thanks for that!

[@rosegold-beats]

You one hell of an engineer!

[@allenrusselljr]

What a great project. Im glad that i somehow stumbled onto your channel. Ill now be watching the curb everywhere i go. Somewhere out there is my vacuum pump.

[@victorpalacios1017]

Excelent aproach, thank you very much this is very usefull and practical.

[@mikethespike7579]

A guess this is for guys who just want to make their own stuff. It's a lot of work for a gadget you can buy for a couple of bucks on eBay or Amazon. The bit about straightening the tubing that goes into the dipstick entrance is a good idea. I've noticed with my efforts that the tube tends to curl up in the engine and miss the oil. Once you've figured out how to suck the engine oil yourself you don't want to go back to doing it the old way. This is faster, cleaner and you save sheds of money.

[@Patriottoo2]

Great tutorial! Now change your moniker to Nodrop (spilled).

[@Nurse_Lucy]

I'm always impressed whenever I watch one of your videos!

[@chrisnotap]

Wow, thank you!

[@davedeatherage4902]

Great idea Chris! Thank you!!! From Oregon, in the coastal mountains.

[@jimsjacob]

Brilliant! Fun project I’d bet and something to save my back from crawling under my cars. For now, I can still do it the old fashioned way, but this could be in my future. I’ll just have to remember how it’s done! 😅

[@jmtx.]

Awesome project! Now to keep an eye out for useful junk on garage day!

[@MiniLuv-1984]

Very good! The details make a world of difference, thanks Chris.

[@troy3456789]

I like this for radiators, brake fluid reservoirs and transmissions (to freshen up the liquids in those). From the radiator and transmission, you'd just need to do it once a week or so for a few weeks until the those are basically brand new liquids.

[@jlucasound]

Absolute Pure Genius!! Thank You!! 😃❤

[@JamesDoylesGarage]

Glad I found you. I'm building my car business and this is a great tool to have in the shop. Thank you.

[@TargaWheels]

I appreciate you getting to, and staying on point. Other people ramble and rant. You just made me subscribe. Thank You. 👍

[@chrisnotap]

Thanks for the sub!

[@hydorah]

I've got a commercial version of this that is hand pumped to build vacuum. It's remarkably similar. This vid is full of a handy little tips like the bard creation and plastic tube straightening

[@captainkirk1745]

GENIUS!!! Many thanks for all you share! 😃

[@chrisnotap]

Glad you like them!

[@selkywaters]

Wow! That's a really useful project!! Nice video!! You've still got it!!

[@chrisnotap]

Thank you! Cheers!

[@nelsonericreed6439]

Love your genius,,,, Plus you explain things supremely well. Thank you!!

[@chrisnotap]

I appreciate that!

[@Dancing_Alone_wRentals]

That was fun, I really enjoyed the idea and the presentation. Great video!

[@67box]

Nice job even comparing vacuum levels of pumps.

[@chrisnotap]

Glad you liked it!

[@garykorzelius5930]

As usual a fantastic job! Thanks Chris!

[@percyroach5195]

That's super and well explained

[@serotonin67]

Dang, I am impressed with your best practice workmanship. If I may suggest your consideration to take a 2nd look at using a feature of your Shop Vac in the blow mode. Put the hose up to the valve cover oil filler and BLOW. I observed almost quart of residual black dirty oil quickly blown out of the oil pan drain plug. I interfaced a little hose to the Oil pan hole... so the blow out doesn't make a mess.

[@chrisnotap]

Interesting.

[@BruceBusby]

This seems like a fun project

[@frenchkey]

Great. Thanks for the metric mesures

[@chrisnotap]

You are welcome!

[@billdodson207]

Really sweet idea - iterated and executed

[@AM-dn4lk]

This video tutorial is chuck full of great information.

[@chrisnotap]

Glad you enjoyed it

[@cherrypicker8897]

Fantastic job.

[@stephenschrader4093]

Awesome. I couldn't come up with an idea for a cheap pump. The refrigerator compressor is just what I needed.

[@KelvinMeeks]

What an excellent tutorial!

[@chrisnotap]

Thanks!!

[@TopCat2021]

Great idea; I'll use the pipe to upgrade the one I made a couple of years ago that uses a 1/2 gallon mason jar. On a side note I have a tool holder that uses 3 inch pvc pipe and an old web belt (or any belt) with a couple of hose clamps makes a very durable handle, which I'll add to the 4 inch ABS.

[@stefanpuszka2835]

Nicely done video Chris

[@chrisnotap]

Glad you enjoyed it!

[@falconthree3815]

Keep the ideas coming--a man after my own ❤️ keep it simple😎. Thanks

[@johngarrett4288]

Could I use a 1/4 HP 3 CFM Air Vacuum Pump for HVAC for the suction side?

[@TheParkAttendant]

A great invention! Keep them coming Chris.

[@sonoffantm]

In a word ... Brilliant !!

[@MrFastFox666]

It's a really cool idea, I might end up making one. Although in my case I still need to jack up my car to get to the oil filter, so by that point I might as well just remove the drain plug.

[@chrisnotap]

Some oil filters are located up top or near the front underneath and you don't have to jack it up.

[@suspence25]

I hope you make more videos. I done ran out of them to watch.

[@stuartschnare152]

I’m sick of spilling oil on my garage floor when I do an oil change. This is just the ticket! Thanks

[@ednargnoslen6609]

Clever, bravo and thanks for sharing

[@jasonyannuccelli2499]

I really enjoy your practical and clever DIY solutions to every day tasks. Keep up the good ideas. I’m Subscribed !

[@chrisnotap]

Awesome, thank you!

[@Einimas]

Good idea, saw a pile of those compressors in a pile at the recyclers....

[@pl747]

We made a large one from a 250 gal propane tank to empty porta potties. It was on a trailer and we ran vacuum from the brake booster to the back of the pickup where there was a ball valve with garden hose fittings. We made a small suction hose from the spiraled suction hose you can buy at TSC and places. It ran into the top of the big tank. We put a big plastic 4 inch valve on the back bottom of the tank for emptying. Also had a two inch hose ran off the top back for a suction hose. The end of it had a ball valve with a piece of two inch pvc to stick in the potties. We put litt notches on the end of it so it could be dead headed and suck the line shut. Worked like a top,

[@chrisnotap]

Using the vacuum from the brake booster hose is clever!! That would be a good powerful suction. I doubt it ever plugged!

[@Storm_Dev]

I'm not even a handy man and these are still very entertaining to watch. Nice work!

[@chrisnotap]

Thanks for that!

[@curtdunlap6818]

Nice job. I have need for a vacuum pump from time to time. I'll have to investigate this further. One thing I would do is to add a safety strap on the top tank clip to prevent a full tank from accidentally slipping out!

[@chrisnotap]

Those "C" parts hold it pretty securely.

[@INTERNA9]

LOVE it!

[@jonnyslc9110]

This is amazing, great work Chris!!

[@Carlos-bk9rk]

Simplesmente maravilhoso!!! Você é demais, Chris

[@xhames61x]

Very nice. Not many DIY videos are this thorough. AAA+++ X 1,000,000

[@chrisnotap]

Wow, thanks!

[@Boaters_hub]

Man i love this! My kinda guy! Takes old junk repurposed it to work for other things! And it looks great!👍

[@chrisnotap]

Thanks! 👍

[@DrewanNicholson]

Thank you! Would love to see a video with tips on how to tackle the filter

[@TundeEszlari]

You are a very good videographer.🤩❤

[@chrisnotap]

Thanks for that great feedback!!

[@MASTER3RDEYE]

Nice set-up.

[@chrisnotap]

Thanks!

[@Flash1857]

Very good idea, thanks

[@HarryJCLK]

I would definitely buy that

[@stuartarneaud218]

Great job like it very much

[@tkdon877]

Love your videos Chris. Hope you'll keep making them! Would love to see more. Take care.

[@chrisnotap]

Thank you! Will do!

[@michaelwalsh7846]

I bought an electric oil sucking pump, but due to the dipstick on a skoda fabia being so narrow (3mm outer size plastic tube max you can use ) in between letting the pump cool it took 6 hrs to suck the oil out!

[@chrisnotap]

Yes the size of the dipstick tube is very important and will slow things down as the diameter is smaller in size.

[@terrywawro2951]

Well thought out!

[@ermannodangelo1062]

Always a pleasure to watch and learn new things. Would it be sucking oil out of the filter at same time?

[@Terrooks]

Great video! Any issues with residual metal particles that settle at the bottom of the oilpan? I've always wanted an oil extractor but I'm worried about buildup. I mean, technically, the oil filter should catch them but bottom draining seems to get those loose particles out a little better

[@chrisnotap]

Any particles in the oil will settle at the bottom of the pan and really not move anywhere. The particles are very small, metal, and have a bit of weight to them. Whether you suck out the oil or drain it from the drain plug doesn't really change things.

[@hartman851]

Please create more video.

[@yvlcartie]

Fax

[@FilmFactry]

Nice doable project

[@mpowersmedia3219]

So after watching your duat collection video I had to sub and check out some others and found another video that I'm gonna have to use to make my own device. Don't know how I'm just now coming.across your channel when you tube is literally all I watch and diy is my main topic of choice. You tube algorithm sucks. Thanks again.

[@DJ-ek5wi]

It's a classy way to do an oil change at home.

[@DONphantasmo]

Wonderful video, Chris. I think you just added a new subscriber!!!

[@chrisnotap]

Awesome, thank you!

[@CzowiekDemolka]

great video, everything is explained

[@chrisnotap]

Glad it was helpful!