Not putting the shell on the cable first... It happens to all of us at least once! 😅
@ElectronicNoobBlog2 жыл бұрын
Very true! Worst when you make waterproofed connector and add silicone glue... don't ask how i know :D
@b67fstb Жыл бұрын
Nice ! Very helpfull ! QUESTION : How do you make BMS CAN BUS cable. ?
@ElectronicNoobBlog Жыл бұрын
I won't be able to help You - I never make it myself (yet). In general Victron is upfront with schematic so I'm sure You can find documentation that state pinout and technical requirement.
@sanderveenman599 Жыл бұрын
so all the wires are 1 on 1 , nothing is crossed.. itsnt this exactly the same as any standard of the shelf ethernet cable then?
@ElectronicNoobBlog Жыл бұрын
Yes - straight 1:1 cable - can be used off shelf without any problems.
@mirendorff Жыл бұрын
@@ElectronicNoobBlog then no need to make cables. a ready 1:1 cable doesn't cost so much
@jdvnautic9 ай бұрын
Well done. 👍
@ElectronicNoobBlog8 ай бұрын
Thank you! 👍
@johnplyler7054 Жыл бұрын
How about a video on how to build a terminator
@ElectronicNoobBlog Жыл бұрын
I can make video like this but it won't be soon - building my solar system is on hold. Just open PDF manual for VE.BUS protocol, there will be information what pins to terminate, buy resistor that correspond with that value, insert it into RJ45 plug and crimp - You are done. If You have problem with it - ask virtually ANY Victron dealer who is installing VE stuff - they will have bunch of them laying around (if you chain multiple devices you don't use them in between and with each device you get them so they are always surplus).
@johnplyler7054 Жыл бұрын
You said you use RJ47 plugs. Isn't it RJ45 instead?
@ElectronicNoobBlog Жыл бұрын
Yes it's RJ45, 8P8C
@hectormolina8159 Жыл бұрын
hi, then the VE.CAN cable between the MPPT and CerboGX is a 568A or 568B, cable. 1:1 ?
@ElectronicNoobBlog Жыл бұрын
1:1 straight cable - wiring standard is just personal preference.
@RA-qt5ky Жыл бұрын
Can I use standard ready made ethernet cables? If they are straight connection.
@ElectronicNoobBlog Жыл бұрын
Sure. What we make on video is just regular straight Ethernet cable. Same way I done my network.
@mirendorff Жыл бұрын
hi, what is the difference between this cable and a ready Ethernet cable with Rj45 plugs? is the pin assignment different?
@ElectronicNoobBlog Жыл бұрын
None - self made cable You can get to exactly demanded length or You can drill hole, put cable & add plug. If You don't need those? Just get regular unshielded straight ethernet cable and it will work perfect.
@johnplyler7054 Жыл бұрын
Can you make your own terminators too?
@ElectronicNoobBlog Жыл бұрын
Sure it's just resistor in plug. I believe pin-out and resistance was in Victron documentation for VE.Bus protocol.
@9111logic Жыл бұрын
Thank you so much for showing us, I followed exactly your instructions and voila', two cables of the exact length for my Victron Photovoltaic system are done 😉 And here is the proof kzbin.info/www/bejne/hX65foqKoNutm9k
@ElectronicNoobBlog Жыл бұрын
You are welcome, glad You are happy! Wish lot sun!
@_JustBeingCasual Жыл бұрын
Where do you buy those crimpers? looks really nice!
@ElectronicNoobBlog Жыл бұрын
Sorry that I missed out Your question, I just grab them online - those are not expensive ones - but slightly better than bottom line. It's nothing fancy that is worth recommending - I'm sure they came in different colors and it's just chines AliExress stuff.