Make your MikroTik Router as an Access Point wireless router using RouterOS v7

[@etzardstrydom]

Honestly, you are the first person to properly explain each step, and most important, WHY you do what you do. Not everyone learns the same! Well done!

[@engryomiadesanya7240]

Thump up for you sir! Your teaching is just on point and easy to comprehend. I recommend to all Mikrotik Router Novice.

[@lamjac88]

Thank you very, very much. I have sorted my parents' problem of Wifi signal issues as well as Ethernet ports in their room.

[@MAICT]

Great Jacques!

[@jakobala]

So grateful for this tutorial.

[@FrancoisHeunis-h9y]

This was really awesome. Extremely helpful and in depth. Thanks a Mil

[@andriyzabavskyy4707]

Thanks for this lab, for newcomers it will help a lot

[@MAICT]

Glad to hear that!

[@NattachaiCharunnarmsirikul]

This is gold.

[@tazvagyok]

Perfect, thank you!

[@jh491]

Thanks to your video i was finally able to get my hap ac2 configured the way i wanted to even though i deviated slightly from your tutorial. very informative and i'm grateful for you doing this easy to understand explanation!

[@MAICT]

Great to hear!

[@mostafaqasemian9477]

Thank you very much for this amazing lesson🙏 i have a question: if i have two mikrotik in one network, how can i connecting these two microtik as one switch in my network? Thank you

[@maboketech5155]

Thanks a lot may God continue to bless you

[@Yusuf-us1tg]

nicely done much appreciated👌

[@chetannaik5199]

Thank you very much. I have used wireless-2G interface as DHCP client and extended the internet to all other physical ports and wireless-5G interface too... Something like a network extender/repeater. I dont know but works for my requirement.

[@makeitcloudy]

Thank you for the video, I found all your materials very consistent and informative. It would be really fantastic if you can elaborate a bit, what is the best way to lower the power sent over the antenas. Some says that it's the gain, some that tx power. I'm really puzzled, can you advise ? I'm sure some people are interested in lowering the power of the WiFi. that would be a great help, cheers

[@MAICT]

it all depends how much power is allowed in your country and how much power your router can emit, also should check the RX sensitivity on the receiver. So there are many factors to take into consideration.

[@antoniocerasuolo757]

excellent!!! THANK YOU!

[@daddycash7076]

I'm grateful

[@llantasgarcia6579]

Hello, If you put all the ports even the wireless on a bridge and turn on DCHP client it will also works as an AP, you just plug the internet cable on any port and the mikrotik will deliver internet on all the rest of the ports, it will not be necesary to set a NAT nor DHCP server, of course the mikrotik will not have a ip address but it works, any inconvenience do it this way?

[@inprosis]

Muy bueno, felicitaciones 👍👍

[@rezamotahari4926]

Hello . one question .My access method at home is through lte modem and it doesn't have bridge capability that Mikrotik can connect. In addition, my internet is gnat type, which means the IP address that the site shows is different from the public address that the modem shows. My Mikrotik cloud service works, but because of NAT, I cannot connect to Mikrotik through the cloud and set up a VPN server with it. Is there a way to do this without a public IP through Cloud Mikrotik? Thanks.

[@bigtimesahead8285]

Thanks a lot for great explanations

[@MAICT]

thank you

[@virt23virt]

Amazing, thanks.

[@thabofrankticharwa9105]

I love your content however I am yet to see anyone with a solution for the constant disconnection of clients on a microtik based hotspot. it would be great to hear from you

[@HSITAFRICA]

what of setting it up as wifi extender

[@hadishar-co1ei]

very good

[@kodok_sawah]

I'm sorry sir, if my ether 1 is red what I should do to fix it?

[@elizarassam8408]

hello, i followed the video, it seems like i get internet access on all 4 Ethernet ports. but when it comes to wlan1, my phone or any other device cannot connect to it wirelessly. i double checked all the information and I don't seem to be missing anything I don't know why its not working. any idea ?

[@MAICT]

Check if your wireless interface is disabled :)

[@MrBazsi888]

which is the best mikrotik access point today ? I have MikroTik RB4011iGS+5HacQ2HnD-IN Router.

[@MAICT]

All are good :)

[@MrBazsi888]

@@MAICT right now i use three MikroTik cAP XL. its works like a charm and elegant looking.

[@MAICT]

@@MrBazsi888 gr8

[@ofiraroya]

Hey can I get internet connection without isp?

[@luminusion]

thank you

[@Fyneskills]

Your video on route summation is incorrect sir. I would have commented on the video, but you turned off the comments.

[@MAICT]

Yes I saw that. Actually the summarization also work the way I did, it just takes 1 bit more. The issue was from the typing that I missed 1 bit.

[@otakoutnik]

Name of this video is misleading. This in not an Access Point configuration, it is router with Wi-Fi. Access point is subdevice in LAN that provides WiFi access to LAN and if that LAN have access to internet it will provide it if configured so.

[@MAICT]

It is clearly mentioned: Access point wireless router.

[@AmanyaHenry859]

𝐘𝐨𝐮 𝐚𝐫𝐞 𝐭𝐡𝐞 𝐦𝐲 𝐛𝐞𝐬𝐭 𝐭𝐞𝐚𝐜𝐡𝐞𝐫 🙏🙏🙏

[@AmanyaHenry859]

𝐘𝐨𝐮 𝐚𝐫𝐞 𝐦𝐲 𝐛𝐞𝐬𝐭 𝐭𝐞𝐚𝐜𝐡𝐞𝐫 🙏🙏

[@onequestonevideo9457]

Thank you