Subscribe to this new channel: / @trythisthing Unboxing and testing the cheapest cordless impact wrench I could afford. It is very good for the money. I bought it in LIDL for 79€.
Пікірлер: 439
@downloadedxzx Жыл бұрын
Upgraded from an older 18v kit. kzbin.infoUgkxW1vOBRCMrgTCDEijzpVzDWsgI-Jm2iQv I independently chose the drill and impact tool, before I came across the kit.I like the 3 speed impact gun. It seems more powerful than my older one, and it can be set to be really gentle. The drill is more appropriately sized for my use. I used to have a hammer drill, but I did not like that it was so big and it was not a great hammer drill. I rather have a smaller drill like this, and then get a corded hammer drill for the odd case I need that.
@dariuszszewczyk31064 жыл бұрын
400Nm seems to be cheap replacement for BMW M3 engine
@MakeAndTest4 жыл бұрын
Man, you made my day hahahah
@piotrradwanski25073 жыл бұрын
@@MakeAndTest also for me :)
@Amer76R2 жыл бұрын
Im happy with this tool, it easely removes the 36 mm VW axle nut. Thumbs up from me, and the battery lasts really long.
@niteblaster13 жыл бұрын
good review😎 the sockets that come with it reduce it's power output as they are not a good fit and they rattle use shorter quality sockets and you will notice and massive difference 😀
@rotorblade95083 жыл бұрын
Yes, force is given by mass and acceleration so basically a hard material produces higher acceleration (deceleration) so a harer socket, harder stud and disc rotor (the studs are bolted into the discs) and a higher mass of the disc produce a greater torque for the same impact gun
@chucky23163 жыл бұрын
How do the sockets stay on mine just fall off. I didn't see this guy putting a pin in either. Do I need a hog ring replaced. I haven't been able to use mine
@chucky23163 жыл бұрын
How do the sockets stay on mine just fall off. I didn't see this guy putting a pin in either. Do I need a hog ring replaced. I haven't been able to use mine
@dushk02 жыл бұрын
@@rotorblade9508 None of that pseudoscience at all! It's just the contact areas and that the socket doesn't deform during the impact. The mass is standing, so a heavier socket would actually hinder acceleration, if it did anything noticeable, that is.
@georgiojansen77582 жыл бұрын
dušan a test would be nice
@denardou4 жыл бұрын
pour l'avoir achetée juste pour tester (j'ai du meilleur matos mais du coup elle restera dans le camion avec les outils de bases ) : -Vous prenez les douilles d'origines, vous les mettez à la poubelle -Mettez des douilles à choc de qualité et vous verrez que le couple affiché est proche ... les douilles fournit mangent énormément de puissance (acier souple "mangeant" l’énergie) -le témoin de batterie ne vaut pas grand chose Sinon pour le prix et garantie c'est très bien
@MakeAndTest4 жыл бұрын
Thank you for sharing your experience.
@nisarzaman3 жыл бұрын
Beautiful silent review
@MrKingbesh4 жыл бұрын
It’s ok if you are using it at home u will need a breaker bar for some bolts for 60 pounds impact drive 4 Amp battery and charger it’s not bad + Lidl sell the battery packs for a good price if u need a new battery after a few years , once u have the battery and charger you can pick up other tools that are sold as body only for a very good price drill grinder compressor and much more but if you want a good impact it’s the Milwaukee 2767-20 , if u have a garage Snapon CT8850,
@donegal2010able4 жыл бұрын
I have a milwaukee 1/2 drive served me well one day something happened I don't know what thought it was the battery bought a new one made no difference it could tighten but not loosen well any who was in lidl one Thursday morning didn't even know they did a 1/2 impact bought it and must say it is better than the milwaukee mind you I bought the milwaukee back in like 2009 I'm sure there much better now. On a side note I used a friend's Hitachi hex impact on site driving 8inch bolt's it was like knife through butter it's really amazing how good all these tools work the air compressor is almost obsolete.
@dushk02 жыл бұрын
Need proper impact rated Cr-Mo forged sockets and it all suddenly works.
@johnwarner38093 жыл бұрын
I have bought this from lidl, it's worth every penny , forget all the barmy demonstrations showing it wont tighten or undo to 400 nm, we're not building bloody battle ships, its got more than enough torque for what its intended for .
@gardenfeed92493 жыл бұрын
I was able to hold the socket in my hand while trying to simulate fastening/releasing wheel nuts. Even on max setting of 400 NM, it was possible to hold the socket by firm hand grip, and this just does not meet my expectations. As I always tighten wheel nuts manually using spanner I have a feel how tight they should be. Rarely using torque wrench. Tried the tool on my wheels bolts and it was not possible to release any bolts I had tightened with spanner, torque on the tool was on max setting of "400 NM" but it was not possible to release any. Will continue to use my trusty spanner and this impact wrench will go back to the shop. I like to trust my hands instead.
@dushk02 жыл бұрын
@@gardenfeed9249 I have the basic model and I would pay for seeing a show where a weakling who makes up BS stories on YT tries to hold that down with their hands... And I'd love to know the brand of gloves if that actually worked out. And yes, I've just made a socket pretty hot trying to give that story a shot. Seriously, you didn't xD
@gardenfeed92492 жыл бұрын
@@dushk0No gloves, I was not filming unfortunately , if I ever find the tool I will demonstrate. Btw, battery was 100%.
@maxextz3 жыл бұрын
I got one of these and it's really good. Great price too. Aldi do their version for the same price but it's only 180 nm. Parkside stuff is good for the DIY dude.
@MakeAndTest3 жыл бұрын
exactly
@typhoontim125 Жыл бұрын
Surely the Aldi one you mention with 180nm is an Impact Driver and not an Impact Wrench. The collet is 1/4 inch & not half inch.
@JohnnyTheCache3 жыл бұрын
Its currently available again at LIDL and I have just bought one (model 2021 ASSK 20-Li A1). After many comments here and at the lidl online shop, I was very curious. After a test I can now say: The thing has POWER !! If your device does not open the bolts on your wheels, you are either doing something wrong or you have a defective device.
@MakeAndTest3 жыл бұрын
It's good to know that you have to press the button and hold it for at least 10 seconds for the best result.
@JohnnyTheCache3 жыл бұрын
@@MakeAndTest Exactly, an impact needs some time. Maybe some people expect it to work like a regular screw driver? Well, it doesn't :D Seriously these Lidl things are great for occasional use
@johnlever66963 жыл бұрын
They have been at your lidl already? They aren’t available till a week on Sunday apparently
@JohnnyTheCache3 жыл бұрын
@@johnlever6696 i got mine from the lidl online shop in germany, it has been available since last week and they still have stock
@johnlever66963 жыл бұрын
@@JohnnyTheCache nothing here in the UK till a week Sunday. I’ll have to wait.
@madcatminis3 жыл бұрын
Good video. Thanks 👍🏼👍🏼 6 adverts for a 10 minute video
@screwsnutsandbolts3 жыл бұрын
Excellent video !
@GenMaster1242 жыл бұрын
Suggest only using impact sockets and then only six sided ones 👍🏻👍🏻
@charlescarabott76923 жыл бұрын
I got the dewalt 1600 nm impact because i already had two 5ah dewalt batteries from another tool but if i fpund this at lidil i might have bought this one and saved some money. Nowhere as powerful as dewalt but probably will do most jobs on a car
@rickilaws9601 Жыл бұрын
the black parkside performance model is an animal of a wrench !!! take tractor wheel nuts out with em .... never seen a performance in the UK .. I think they sell them in Europe . it's a serious bit of kit !!!!
@InBoostWeTrust7MGTE4 жыл бұрын
3:40 now that sounds like lawnmower engine
@michaelstubbs4518 Жыл бұрын
This gun is good for a mid torque impact wrench but you should never torque a wheel up that high you will sher off the bolts.
@MakeAndTest Жыл бұрын
youre right. But I had to test it somehow. It's an old car that I dont use
@overhaulgamerz8552 Жыл бұрын
I agree, don't use this to tighten the nuts, previous mechanic tighten my car wheels with impact wrench and when I went to change tyres, tyre shop had a hard time removing the nuts.
@dalebassett61194 ай бұрын
I accidently torqued one of my car bolts on no 3 setting on a milwaukee high impact wrench that has 1650 torque it didn't rip off 😂
@DomRivers673 ай бұрын
So, was it reasonably accurate?...it seemed to take another quarter turn on the lower settings to get to the correct torque
I bought one, works fine. The circlip socket retainer isn't very good. I'll get a couple of ball bearings and a suitable spring and fit one, easy enough...
@dmitrys13935 ай бұрын
Got mine a month ago and tested it yesterday on some brakes job and i was disappointed with it because looks like the mechanism starts to slip somehow when it's not perfectly aligned, i dont know how it works but the bolt goes easily for a second and then the next second impacting sound changes and the bolt just stays in place and then if you wiggle the tool a little bit the impacting sound goes back to normal and the bolt goes normally again for 1-2 seconds until it stops again. That was super annoying and i had to undo the bolt with hands. Probably defective device or something
@lummeltje4 жыл бұрын
wou eerst een milwaukee stubby 12v kopen maar dit is al prima voor wat ik er mee wil gaan doen! dank voor de video!
@MakeAndTest4 жыл бұрын
Ja, dit is erg goed voor de hele werkplaats.
@jjmmjj99994 жыл бұрын
I don't understand German but I own a milwaukee stubby 12v and was impressed with this tool for less than half the price
@MakeAndTest4 жыл бұрын
@@jjmmjj9999 it does the job
@grazianolaudisio36444 жыл бұрын
Wat ga je doen dan?
@lummeltje4 жыл бұрын
Graziano Laudisio brommers opknappen, en de jaarlijkse bandenwissel
@dennisinanir33852 жыл бұрын
goeie video thanks! LIDL heeft goed spul
@donegal2010able4 жыл бұрын
The 20v range is the bomb, I've collected quite a few of them 14 battery's the first set of 2018 batteries work just a good as new and I use them all the time. Parkside make dam good tools the 4 in one looks flimsy but its pretty handy I use the saw all the time
@12BlackKnight343 жыл бұрын
Damn good tools.... yeah right...
@user-zt4ry9hm9u3 жыл бұрын
There's nothing really wrong with the tools and they are priced well, however they are same Chinese made generic tools that are also sold under many different brands such as Stanley, silverline to name afew
@RobertBosch93973 жыл бұрын
Nice video 👌, i bought 2 in Germany, they work excellent 👍
@UltimateTBone2 жыл бұрын
Hi Robert, nice to see you here :-) I read complains on the Lidl site about loosening wheel bolts. When the are tightened with 120NM, only the 400NM stand on the Parkside will get them loose. And tightning with 100NM would be around 75NM. But you're using it on your work, so I'm curious about your opinion.
@RobertBosch93972 жыл бұрын
@@UltimateTBone I don't use it anymore T this moment, it's a good tool but much to light, I bought a milwaukee M18 fuel, 1700 nm 😂😂
@kmieciu4ever4 жыл бұрын
8:36 metalowa brecha wygrywa :-)
@derwaldmeister39543 жыл бұрын
I compared the torque from this thing to a torque wrench. The torque is not half as high as declared. 400 Nm is not even 200 Nm when loosening and tightening. 200 Nm setting is only 90 Nm. If wheel screws are rusty you can be lucky if you can loosen them. I also own the smaller version of this impact driver. Parkside says 180 Nm. Even if I use the shock adapter of milwaukee I can't loosen a screw what is tighten with 50 Nm.
@MakeAndTest3 жыл бұрын
Great info. Thanks for sharing.
@Ljosi3 жыл бұрын
something is wrong with your unit, or you are using it with a 2Amp battery instead of 4.. I tested mine and it's very close to the advertised numbers (+- 5%)
@rickjohnson87823 жыл бұрын
Should be reported to trading standards . Clearly doesn't offer the performance it says it does .
@mindaugas19064 жыл бұрын
Good review. With proper impact socket cr-m not original cr-v ones it produces 300+ nm torque. Not 400nm as claimed but still good enough for the money.
@MakeAndTest4 жыл бұрын
Thanks. I've come to the same conclusion. Not the advertised torque, but it will be usefull in the workshop anyway.
@animation01boy4 жыл бұрын
say whats actually the difference between cr-v and cr-m thnks?
@derbigpr5004 жыл бұрын
You don't even need 400 Nm for anything really. Even 100 is overkill for most things, unless you intend to work on tanks and trains LOL.
@mindaugas19064 жыл бұрын
@@derbigpr500 you bet its not overkill... tire shops sometimes overtorque wheel bolts to 300+ nm. Good luck removing them by hand without long bar. This wrench is not strong enough for that. And you always need more torque because tightening torque is always way less.
@Neulich4 жыл бұрын
@@mindaugas1906 everything you said i can confirm. Shops overtightening and ~300nm max. on this mashine.
@DashCamSerbia4 жыл бұрын
I bought an impact socet for mine. You need an impact socet to get better results. They transfer the force better.
@donegal2010able4 жыл бұрын
Too right I've seen a chrome socket explode when trying to remove a seized axel nut, it was like a grenade 3 of us up close just staring seeing if it'll work luckily no one lost an eye or a nose all that was left was the bottom half, it was a decent socket Halfords brand. Impact for impact they are softer and will wear faster but jesus they are safer
@DashCamSerbia3 жыл бұрын
@flip inheck No, it comes with 4 sockets. But they are not impact. They are regular Ch-V painted black.
@DashCamSerbia3 жыл бұрын
@flip inheck Not untill it breaks and sends shrapnel into you. And they don't transfer torque as good as the impact ones.
@s14driver4 жыл бұрын
It is useless for a car wheels removal, 5 out of ten screws won't be removed without breaker bar. Works good on recently mounted maybe greased screws up to M12 thread torqued up to spec or lower. If you would mainly use this for car wheels removal or similar jobs, save up some money and search for min 600+Nm. Good value for small bolts though....
@MakeAndTest4 жыл бұрын
thanks for your feedback man :)
@DashCamSerbia4 жыл бұрын
It removed my wheel bolts torqued at 105-110 Nm like they are nothing. But I used an impact socket with it.
@kayathepiratebaykid4 жыл бұрын
Then again people who work on their own cars, will generally tighten and loosen their wheels every half year at least and grease them up.
@bigtrev8xl2 жыл бұрын
@@kayathepiratebaykid 🤣🤣🤣🤣🤣🤣🤣🤣
@oneummah67952 жыл бұрын
Great video, the torque settings are not true. As a example you would never torque your car wheel nuts more than 120 NM in a majority of vehicles otherwise you can snap the wheel bolt. It makes sense to buy a proper brand like Milwaukee.
@davidcole58427 ай бұрын
good demo many thanks
@gamefoorum3 жыл бұрын
Why are you trying 210nm precision when most of the cars have around 110-120nm ?
@MakeAndTest3 жыл бұрын
Yeah I know I messed that up a little bit. But I had to test it on a much bigger number than just 100Nm. Also I dont really care about my car anymore, so it can take a beating :)
@hakansen71913 жыл бұрын
Insane Builds it only tightenes up to 100nm. The other numbers are for loosening the bolts
@stay_jaki3 жыл бұрын
Milwaukee No.1
@hadipewe3 жыл бұрын
do you mind to make some video and release the bolt of front strut ( it is m21 tight at 165 nm, two bolt on bottom side of the strut), also is it possible to release the suspension bolt, the center bolt of front tire
@Ljosi3 жыл бұрын
@@hakansen7191 that's the case with the corded model, but the cordless one does both up to 400 Nm
@Soni-sGarage3 жыл бұрын
Meiner ist nach 5 Monaten inkl Akku kaputt gegangen 😡😡😡 aber haben ohne Probleme komplett ein neues bekommen. Lg Soni’s Garage
@socialghost44004 жыл бұрын
Good review, I bought the very same one in Lidl last week, so far it has worked the charm, my only complains are that it is not a brushless motor and theres no locking ball for the sockets (there is a locking ring tho, and I have not had any sockets fall off either, so not the biggest issue), but I mean for the price, those are easy to live with....anyway....Subscribed!
@MakeAndTest4 жыл бұрын
Yeah I noticed that sparks are shining inside the machine when you suddenly stop it. I just dont understand why are there differences in prices. I paid 79€ some say it was only 59€...
@socialghost44004 жыл бұрын
Insane Builds I guess it varies from country to country, I paid €75 / 555DKK for mine in Denmark
@MakeAndTest4 жыл бұрын
@@socialghost4400 for the same kit? Fast charger and battery included?
@socialghost44004 жыл бұрын
Insane Builds yes, and the four sockets 🙂
@saschaschulz87304 жыл бұрын
Des doch nur Müll des gelumpe
@m.b.4627 Жыл бұрын
Das ist das allerletzte Ding, was am 09.01.23 bei Lidl angeboten wurde, PASSK 20-Li A1! Schafft nicht mal, Radschrauben mit 130 NM zu lösen! Obwohl ich die Schrauben vorher manuell gelöst habe und mit dem Drehmoment auf 130 NM angezogen habe, um sie dann mit dem Schrauber zu lösen. Ging sofort zurück zu Lidl. Weiß nicht, wie das Video zustande kam!
@BedsitBob2 ай бұрын
of course, you shouldn't really be using an impact wrench to tighten wheel nuts.
@ronin58923 жыл бұрын
Con 400 NM allenta i bulloni dei semiassi é una bomba
@ufs9103 жыл бұрын
Gutes Video gemacht.
@electricdixie343 жыл бұрын
Brilliant video well tested
@zfloz98953 жыл бұрын
If you put a De Walt on those wheel studs, it will play with them.
@SUNSETRETREATSXM2 жыл бұрын
Goede test!
@MrPabsUk3 жыл бұрын
I thought you were going to try the crankshaft pulley bolt at the end! Oh well! I think I`ll stick to my Makita 1000nm impact wrench, costs a lot more, but MUCH stronger, will last MUCH longer, & the batteries & chargers will be available, anywhere, for decades..
@MakeAndTest3 жыл бұрын
I'll try that machine next. Wats the specific model?
@MrPabsUk3 жыл бұрын
@@MakeAndTest Mine is a Makita DTW1002Z. Its amazing. Not cheap, but amazing!
@MakeAndTest3 жыл бұрын
@@MrPabsUk I'm glad you like it. If I have time and money I'll test it.
@johnlever66963 жыл бұрын
You can’t even compare the two and it’s silly to do so.
@dushk02 жыл бұрын
Dream on! Using an impact tool for decades... And who wants new batteries on a yr. 2000 battery-powered tool at this age?
@aasgardthor211 ай бұрын
Awesome review
@MakeAndTest11 ай бұрын
Glad you enjoyed it
@TheHamouda Жыл бұрын
wheel should be torque 110NM N0T 220 NM.OVER ALL GOOD DEMONSTRATION
@domigashi4 жыл бұрын
Das Problem liegt nicht beim Akkuschlagschrauber, sondern die Schraubnüsse sind von Parkside zu dünn leider, besorg dir die Schraubnüsse von andere Hersteller wie z.B von Bosch, die dicker und stabiler sind, dann wirst du sehen, dass der Akkuschlagschrauber von Parkside sehr gut ist und jede schraube Sekundenschnell aufmacht.
@edinfahrzeugdiagnose3 жыл бұрын
Hey meinst du wenn ich mir die Alufelgen Schraubnüsse von Lidl für 10€ dazu kaufe kriege ich auch die Mutter gelöst oder sind die auch scheiße ?
@makakk03 жыл бұрын
@@edinfahrzeugdiagnose es gibt ein sehr gutes ungarisches Video dazu, hier probiert er mit den originalen und mit den CrMo Schraubnüssen: kzbin.info/www/bejne/iJrFfXlqh5Ksi80
@Alexxx2210813 жыл бұрын
@@edinfahrzeugdiagnose ich habe mir auch diesen schlagschrauber gekauft und habe zuerst die beigelegten nüsse probiert. ich habe die schrauben nicht gelöst bekommen. daraufhin habe ich mir schlagschrauber nüsse aus CHROM-MOLYBDÄN gekauft und die schrauben gingen ganz leicht auf. ich glaube bei lild gibt es die auch zu kaufen oder? wenn ja dann auf jeden fall holen. denn sonst wirst du die schrauben nicht oder kaum lösen können
@edinfahrzeugdiagnose3 жыл бұрын
@@Alexxx221081 ok wunderbar danke dir für die Antwort. Werde ich mir dann holen
@aspos4287 Жыл бұрын
Il est prouvé que les valeurs sur la machine sont à diviser (presque)par deux (voir les autres tests sur KZbin)...
@hofi18154 жыл бұрын
Hallo, du hast ein tolles Video gemacht, endlich mal kein gelaber und falsche Infos, sondern einfach einmal zeigen was wirklich Sache ist. ---------TOPP ----- Das versteht jeder und es wird nicht geschummelt. Ich hatte mir auch den den Lidl KFZ Schlagschrauber gekauft, musste aber dann bei den ersten Tests feststellen das der Schlagschrauber die versprochenen 400nm nicht leisten kann. Bei verschiedenen Tests mit Accuschlagschrauber und Drehmomentschlüssel komme ich auf maximal 200nm löse Modus. Eine Schraube die mit 200nm angezogen ist kann ich nur mit der Einstellung 400nm lösen. Habe das Teil zurückgegeben.
@MakeAndTest4 жыл бұрын
Vielen Dank für Ihre Erfahrungen.
@horstniebuhr11674 жыл бұрын
Der Parkside schneidet schon ziemlich gut ab im Vergleich zu anderen Produkten. Der hat einige verglichen: m.kzbin.info/www/bejne/sIrde5-jg7aAm68 Wie die Hersteller auf ihre NM Angaben kommen, würd mich aber auch mal interessieren.
@einfachmicky84254 жыл бұрын
Hast du die dabei liegenden Nüssen benutzt? Es wird in einigen Videos geantwortet, das die Nüsse nix taugen und er deswegen seine volle leistung nicht auf die Schraube bringen kann. Haben bessere Nüsse genommen und er konnte dann seine Kraft auch voll übertragen. lg
@nguyent24773 жыл бұрын
Only Makita DTW285 number 👍🇯🇵
@divljacina13 жыл бұрын
very VERY nice tool....but dont expect miracles :) have it few years now.....
@Twinturbo_4 ай бұрын
210nm on wheels??? Madness. Should be 100-120 depending on car brand
@MakeAndTest4 ай бұрын
It was just for test
@Twinturbo_4 ай бұрын
@@MakeAndTest then its okay! Great video thanks
@derbigpr5004 жыл бұрын
Hahah I bought this in Lidl too, nothing wrong with it. Will see how long it will last for occasional repairs.
@MakeAndTest4 жыл бұрын
It works just fine for me. All around good tool for a home workshop.
@shalvabenidze70454 жыл бұрын
@@MakeAndTest qué precio tiene?
@MrBadboyrus3 жыл бұрын
how much you pay for it?
@johnlever66963 жыл бұрын
With normal torqued up wheel it’s and bolts will this impact undo them?
@nabilbourouisa3 жыл бұрын
@@johnlever6696 yes, wheels on my car are torqued to 130nm (ideal torque), it does it without problems
@user-lc1um8xu7d3 жыл бұрын
Очень напоминает ЗУБР ГУЛ 401. Наверное на одном заводе делают в Китае. Нет в нём 400 Нм. Ему красная цена с 1 АКБ 4000 рублей.
@Grozniyterek3 жыл бұрын
Так это не дорогая модель можно сказать до первой поломки и потом на мусор
@rondhole3 жыл бұрын
Most Toyota and subaru had 103Nm torque for wheel
@poppsmiel47274 жыл бұрын
Un péteuse n'est pas fait pour serrer au couple....uniquement pour desserrer donc normal de ne pas avoir le couplé sélectionné de sur le serrage des roues.. '. Qui doit se faire à la clé dynamométrique dans tous les cas.
@MakeAndTest4 жыл бұрын
Thank you for sharing vital information.
@pdany44 жыл бұрын
C'est du désserrage qu'il fait :)
@poppsmiel47274 жыл бұрын
@@pdany4 pas du tout à 2:30 il montre que sa clé dynamo est au max à 240Nm et ensuite il serre les écrous aux différents couples de la péteuse 200 300 ect... Et on voit que même régler à 300 ensuite il arrive encore à serrer avant que sa clé déclenche ce qui veut dire que la 300 Nm de la clé ne marche pas pour le serrage.... Ce qui est normal d'où mon commentaire 😉
@mtay653 жыл бұрын
I still love my WORX WU279.
@mtay653 жыл бұрын
@flip inheck Time to switch to 20V as 20V is so popular now. 18V batteries are too old to be found.
@mtay653 жыл бұрын
@flip inheck Change your impact drill to 20V type. You would be amazed with WU380S.
@martinatrybusiewicz24052 жыл бұрын
Will this be enough for a stubborn sump plug? Or to remove drop link locking nuts?
@Asad-2166 Жыл бұрын
Piece of cake
@SBBUK3 ай бұрын
Drop links yes. For a sump plug i'd stick to a normal breaker bar as you will have a really bad time if you damage the thread.
@mattiapresti72953 жыл бұрын
400Nm means that you could stop your citycar's engine and also make it running backward
@MakeAndTest3 жыл бұрын
you got a point there man
@massimo70794 жыл бұрын
Pagato ieri 02/07/2020 59,00 euro alla lidl
@Asad-2166 Жыл бұрын
Now battery charger sold separately 😢
@1marcelfilms4 жыл бұрын
Never seen this in lidl before
@voycok36394 жыл бұрын
Selling once a year.
@rustypanda4 жыл бұрын
Bonjour pour le prix elle semble très correct
@Fanatiekeling747 Жыл бұрын
Very nice vid. !
@henrykinfri1438 Жыл бұрын
Ça vaut le coup de l'équipe et d'une batterie de 8ah ?
@dergeneralist71063 жыл бұрын
Good Test, but the impact driver has no power.
@gardenfeed92493 жыл бұрын
I agree. I always trust my hands when tightening wheel bolts. This tool was not able to release any.
@muhammadakhyar84364 жыл бұрын
Can your dellevery to Brunei Darussalam?
@momoabdel56944 жыл бұрын
Bonjour merci pour le tuto,et puis ça vaut le coup de l acheter pour la mécanique auto???
@Crocodeal3544 жыл бұрын
Un peu lourde mais utile pour les roues etc je devisse du 200-250 nm et revisse le même
@Darag11232 жыл бұрын
I have this gun and I have the gun for the compressor. the Parkside gun won't even undo lug nuts.
@abrahamcoga8424 Жыл бұрын
Video muy bien echo 👌👌
@Domenico-ow8jo4 жыл бұрын
test einhell TE-CW 18 Li Brushless VS Impact driver Parkside PASSK 20 L-iA1 einhell 215nm VS parkside 400nm
@stipestipe45603 жыл бұрын
Einhell win 😂
@Domenico-ow8jo3 жыл бұрын
@@stipestipe4560 🤔
@liamhoanzl29203 жыл бұрын
I had an Einhell before and it crapped out after an easy repair , it just doesn't stopped spinning
@williammincher683 жыл бұрын
Einhell and parkside are literally made in the same factory its just rebranded parkside for lidl. Google it
@curtisjeffery87233 жыл бұрын
Those torque selections are for loosening, for safety reasons and to prevent over tightening will only torque to 100nm
@aleddavies7703 жыл бұрын
Curtis Jeffery how do you know that ?
@curtisjeffery87233 жыл бұрын
@@aleddavies770 the last parkside impact I had (12v one) had that feature in built, but I know from workings of impacts is that the selection button is for loosening torque (pretty sure it mentions in user manual too)
@aleddavies7703 жыл бұрын
Curtis Jeffery I have this one. I bought it new yesterday. It says in the manual to just use the smallest setting to tighten nuts to avoid over tightening. So you can't tighten any more than 100 N/M ?
@Pjotr19823 жыл бұрын
Tie dodávané CrV nádstavce sú blato, treba použiť kvalitné chróm molybdénové a dá sa z toho dostať cca 350Nm.
@giovannir.79733 жыл бұрын
carica prima la batteria e vedrai che funziona bene, avevo fatto lo stesso errore.
@cardo11114 жыл бұрын
You didn't open the box with a reciprocating saw like AvE does ?
@MakeAndTest4 жыл бұрын
Can you give me more context, cuz I don't know what you're trying to ask me?
@cardo11114 жыл бұрын
Insane Builds I Appreciate the response. I was joking, there is a channel called AvE where the creator opens his brand new tools and other items he tests in potentially damaging ways often using saws.
@MakeAndTest4 жыл бұрын
@@cardo1111 Ahh ok. Nice one hahah
@user-qy8tb6gp8j4 жыл бұрын
Very good Strong test
@makantahi37313 ай бұрын
so lidls 400nm is 200nm in real life
@MakeAndTest3 ай бұрын
Yesterday I tried it on my wheels. It could not remove the bolts that were tightened to 125Nm
@oliversatory14943 жыл бұрын
Funny. Mine couldn't get the Bolts loose from my car. Why does it work in these videos? You know the answer, don't you?
@MakeAndTest3 жыл бұрын
I heard you have to press the button and hold it for at least 10 to 15 seconds. Only then it goes to full power. Also you must have cr-Mo sockets for better results.
@oliversatory14943 жыл бұрын
@@MakeAndTest I stopped when it started to smoke
@MakeAndTest3 жыл бұрын
Well...thats not good. Refund it. I think it has a 3 year warranty
@oliversatory14943 жыл бұрын
@@MakeAndTest I sent it already back and bought one from Milwaukee. Endless power!
@MakeAndTest3 жыл бұрын
@@oliversatory1494 You like Milwaukee? How does it compare? How much torque does it make?
@leszekm44144 жыл бұрын
Szkoda że ich nie ma w sklepach już
@nadneDonaDon2 жыл бұрын
Jsou porad na prodej.
@user-bp9uo3bz1l Жыл бұрын
ប៉ុសផ្សានឹងដំលៃម៉ានបង
@InverJaze Жыл бұрын
Wohw the wheel nut is way too tight.
@joseduarte10213 жыл бұрын
Amigo sabe aonde posso comprar urgentemente uma pistola dessas Obrigado
@saudinord24812 жыл бұрын
Хороший инструмент для себя и цена норм!Надо брать!
@nadneDonaDon2 жыл бұрын
Бери не пожалеешь. У меня эта версия и та сильная
@user-wu5en9un1o Жыл бұрын
@@nadneDonaDon ну и как работает?
@ahmedadegboyega36783 жыл бұрын
I am in south Africa. How can I get one?
@jocalibusohump4 жыл бұрын
Good vids sir I wanted to buy soon bec every weekend I go in aldi and lydl here in Carmarthen 😂
@mr.pinter10804 жыл бұрын
Use with Cr-Mo Socket, it is stronger 👌🏻
@MakeAndTest4 жыл бұрын
Will do, next time I use it.
@bars7871 Жыл бұрын
Где такой купить в россии?
@olivierberg97713 жыл бұрын
Kan je hiermee de vario van een scooter los halen?
@stepankenig29054 жыл бұрын
Подскажи пожалуйста ссылку на litl где заказываешь. За раннее спасибо.
@oleglvl3 жыл бұрын
У Лидл нет интернет магазина. Только в самом магазине можно взять
@SplinterPlay3 жыл бұрын
@@oleglvl вообще то есть
@SplinterPlay3 жыл бұрын
Есть два похожих только в цене немного отличаются 1: www.lidl.de/de/p350791?productId=350791&countryCode=DE 2: www.lidl.de/de/p350790?productId=350790&countryCode=DE А вот нашёл ещё только без аккумулятора: www.lidl.de/de/p355166?productId=355166&countryCode=DE
@dfg95623 жыл бұрын
@@oleglvl www.lidl-sklep.pl/ это в Польше, часто там покупаю. Гайковерт тоже имеется в коллекции, кстати не плох. Отправка только по територии Польши. Насколько я знаю лидл везде имеет онлайн магазины.
@kush34242 жыл бұрын
How to buy this product?
@alxrilli4 жыл бұрын
It s 160nm real max
@AncorPereiraValencia3 жыл бұрын
Hola, donde la compraste a ese precio?
@Giancarlo-ol2mu3 жыл бұрын
I don't know how long this toy screwdriver can last as it only costs 79 €! If you want a tool that lasts over time you have to spend at least € 400/500, see DeWalt or Milwaukee and some other brands.
@liamhoanzl29203 жыл бұрын
I have it since it came out and it was used well not only on cars also on Traktors . So cheap is not always bad or is it ? But I have to say that the sockets are crap they rounded out fast
@johnlever66963 жыл бұрын
Completely depends on how you are using it. If you are a mechanic or a steel erector then fair enough, spend more. But if you are a DIYer and do wheel rotations and put the odd coach bolt in then it’s enough and perfectly fine.
@valeriocoelho81384 жыл бұрын
A chave tem o maximo binario no fim de 30s. Aqui nem 10s foi aplicado. Alem do mais os valores serao mais corretos com chaves de qualidade
@MakeAndTest4 жыл бұрын
Thank you for the help. I'll try it next time.
@stephane548803 жыл бұрын
Il faut changer les douilles sinon ça marche mal..moi j ai pris leur douilles blanche et a 200 nm ça desserre facile sinon avec les noires non il faut mettre à donf
@typhoonm.24323 жыл бұрын
How much nm is its resl powe?
@Thanhnguyen-cw9db2 жыл бұрын
Có ai biết ở đâu bán hiệu này không
@faizansportsbikework10903 жыл бұрын
Is brother avilabel in India or not
@gustavomejiacarmona2 жыл бұрын
Donde la compro
@CoisasdeMacho3 жыл бұрын
I have a Makita dtw1002z that can remove any Screw, It was useful to change the crankshaft pulley on my bmw e46
@knightsgarage16444 жыл бұрын
Just buy Milwaukee.
@benogorman80614 жыл бұрын
knightsgarage supose u are pretty hard
@davidelliott58434 жыл бұрын
If you use it every day Milwaukee Bosch DeWalt etc can take the pace. If you do the odd jobs at weekends the Lidl too will do just as well. I have the angle grinder. Actually prefer it to the full price Hitachi corded which stripped its gears after very little use.
@benogorman80614 жыл бұрын
David Elliott here hai i dont care
@johnnycassell23054 жыл бұрын
Thank fuck there were no more sockets after the 23mm