Parkside Impact Wrench PASSK 20-LI A1 vs PASSK 20-LI B2

A new version PASSK 20-LI B2 of the popular impact wrench from Parkside is available - lets compare it to its older predecessor PASSK 20-LI A1

[@mypadmi8656]

Excellent video, thanks for this comparison!!

[@TheMidnightrider67]

The B2 comes with a cell ballanced 4amp battery in uk the A1 just a none balanced 4amp power pack...thanks for your video interesting to see what's inside am retired car mechanic and still do mechanical work and love parkside cordless tools I have complete range

[@Sanychmann]

which is better?

[@TheMidnightrider67]

@@Sanychmann cell ballanced battery is better

[@jeanenamoncada1494]

It is a strange question to rate the “weight” of this unit because it is basically a giant torque electric motor on the end of a handle- so yes, it is top heavy. I’ve had the chance to use it a couple times to remove tires and wheels and it works great kzbin.infoUgkx4ynqaujg7rZKFapA8s29kTpRszJGa3-K There are three torque settings so that you don’t overdo it and strip a lug. Very happy with it, especially with the price of buying it as a bare tool.

[@ps7539]

never in my life have i seen a tyre shop (or mechanic for that matter) use a torque wrench for car wheels. just pneumatic and they keep hammering. I wonder to what torque those are set

[@kevinmarsh5034]

I bought one of these about 2 years ago (have A1) and it is brilliant. Always reliable, easy and quick to use and up to the job. In the workshop I have the choice of both air and electric and electric wins most times. I would always use the impact sockets, much safer. (do you have a test on Parksides electric ratchet?)

[@icku]

I will have the ratchet very soon and will revieiw it.

[@kevinmarsh5034]

Thank you, already looking forward to it.

[@shamilbasayev952]

Sehr gutes Video!

[@jeansimoes7315]

Hi, congratulations on the video. I have an A1 400nm, and I want to install a brushless motor because the original motor heated up to the point of smoke coming out and the brush wore out prematurely. If possible, what engine would be compatible?

[@gagiska83]

Excellent video

[@soisun2658]

Good video

[@gm6941]

bello, bravo, ciao

[@VR46Monster]

podle mojeho pruzkumu... A1 verze dokáže povolit 210nm na hliníkových discích bez většího problému. ani ne sekundu a šroub povolí. takže sme 2x ověřili že se vyplatí si ho koupit! :D i did my research with A1 version, its able to unscrew bolt from aluminum rims torqued 210nm without any problem.... it takes less then second and it loosens the bolt. so its 2x prooved that its worth the money!

[@Sanychmann]

It was usefull. I have one of them.

[@ludmilkushinov9652]

Congrats for English speaking video, at least commentary below are restricted only to people with base language level that will raise level a lot :) Regarding test, I really want to see on torque tested as previous videos with A1 version because there is new electronic control of battery and it could be made to use more or less power that will change end result(surely not significantly). Plus I see that B2 was tested with A1. On mine side I have tested on tightening wheel nuts and on 400Nm it was not able to reach even 200Nm when I finishing with mechanical dynamometric tool.

[@icku]

Thanks. Still working on my hydraulic torque tester and when finished it will eliminate any doubts which tool is more powerful. And not just between those two - I'm planing to make a whole bunch of videos testing variaty of impact tools.

[@roccomarafioti463]

Prezzo grazie mille

[@AAAlexAlex]

Почему не проверил на закручивание болтов в автомобиле , с какой силой закручивает ??

[@martinsmillers1058]

Because there is a specific torque value to which you must tighten wheel nuts, you should never exceed that value. And by testing how big value can achieve these electric wrenches you can easily over torque wheel nuts

[@voynata7426]

Здравей колега, за какви пари взе нови я гайковерт, че ги гледам по 170 и се чудя дали са на оферта защото стария модел мисля че беше на 140 по едно време

[@icku]

За 170 го взех. Мдам преди бяха по 140...

[@voynata7426]

@@icku Чудя се дали си заслужава ако беше 140 веднага го взимах 😅😅

[@icku]

@@voynata7426 Ами аз А1 версията я взех преди 2 години и нещо и тогава беше още по евтина - 110лв. Машинката е добра, но за 170 наистина е малко скъпичка вече.

[@fred-san]

see Bricovideo OVH drillpro 1/4 inch but better than prkside perf. 4Ah (same price except battery...).

[@Vaiper911]

Is there a possibility to replace a brushes?

[@icku]

If you manage to find spare - yes, you can replace them.

[@gurunathpapisetty6486]

Is it a brushless motor?

[@henrykinfri1438]

No

[@kbv6065]

Здравейте!Може ли да ми напишете означението на малката интегралка SOIC-8 на платката за управление на B2, че моята изгърмя ама не се вижда означението.Благодаря!

[@icku]

Продадох машината отдавна. Ще погледна на някое клипче дали не съм снимал тази интегралка, но ме съмнява.

[@kbv6065]

@@icku Благодаря за отзивчивостта!Намерих и означението - EG2131.Специализирана ИС за управление на MOS транзистори. Ако на някой му затрябва- често изгаря при претоварване и изгаряне на мощните MOS транзистори.

[@Vladg96]

Купил C3 версию, максимум 80 нм 🤮

[@andpan3478]

dude, how about testing on 100N on all position , what nonsense it this to test on 100N tightn to unscrew on 400N :D are you serios ?