Maker Pipe Hacks, Tips and Tricks @ MKE Gadgets

[@jerico902]

Thanks for this! I'll try out your 3d prints! 👍

[@mkegadgets4380]

Let me know how it turns out. Please consider subscribing if you haven’t.

[@williamsmillie4357]

The presenter is a skilled craftsman with great tips, thanks.

[@mkegadgets4380]

Thank you for your positive comment. Please consider subscribing I really appreciate your support.

[@m.o.f8720]

I can only add my 👍👍 to all the other comments below as they say what I would say as well or better than I. Excellent video. Got me interested in exploring the 3D Printing rabbit hole...( as if I don't already have enough like MakerPipe and going off grid to upset friends and family with.....). Hopefully you have some equally excellent videos on that. Thanks again

[@mkegadgets4380]

Thanks for your positive comment. Please consider supporting my channel by subscribing. I would really enjoy it.

[@motoservo]

Good stuff, thanks for sharing.

[@mkegadgets4380]

Thanks for your comment I hope you found the video helpful. Check out my other 151 videos I have on KZbin. I try to do a new video each Wednesday.

[@frankenpine8071]

Excellent demo ! Thanks for sharing !

[@mkegadgets4380]

Thank you for the positive positive comment. Please consider subscribing my channel if you haven’t. I’m trying to get to 1 million subscribers by the end of the year. Check out my other 225 videos. I’m sure you’re gonna find something you would like. Thanks again.

[@josegolfpiper8342]

Great Video!! I learned a lot!! Thanks for sharing...........Jose from Texas

[@mkegadgets4380]

Thank you for your comment. I hope it helps you when you use and build Maker Pipe. Please support my channel by Subscribing. And check out my other 160 videos.

[@partytempo]

Thanks to this channel, I upgraded my plastic toro battery string trimmer using 3/4" EMT. Feels like a real tool and no longer a toy 🤣

[@mkegadgets4380]

That Maker Pipe is some crazy stuff you’re only limited to your imagination.

[@Makelifehappennow]

Nice video. Helpful. I like the 3D printed feet. How well does the plastic thread hold the 3/16" bolts?

[@mkegadgets4380]

So far so good have not had a problem with them.

[@dianeladico1769]

Hi, I found you through Maker Pipe. Great video. You're my new hero. Subscribed. Thanks so much for sharing.

[@mkegadgets4380]

Thanks for your positive comment and supporting me by subscribing to my Chanel. Check out my other over 119 videos on KZbin. New video on most Wednesday, your going to like the next one.

[@dianeladico1769]

@@mkegadgets4380 Oh yes, I'm going to check them all out-this one was clear and easy to understand and had such good ideas.

[@erikaamac2727]

Thank you I feel much more prepared and ready to order!

[@mkegadgets4380]

Thanks for your positive, please support my channel by subscribing. I have five or six videos Om maker pipe. You might wanna view him before your order comes in. Thanks again

[@HD_Machinist]

All these ideas you show makes me want to build something now. It looks very easy to do.

[@mkegadgets4380]

Thank you for your positive comment. It is easier than you think. The first thing you Gotta do is just get started.

[@lakeratatouille]

I'm here from maker pipe. You've got some great ideas Thanks!

[@mkegadgets4380]

Thanks for your positive comment please support me by subscribing to my channel if you have not. And check out my other over 100 videos on KZbin. Thanks for your support. New video on most Wednesday, your going to like the next one.

[@partytempo]

This is really cool. I've never seen anyone mention Maker Pipe. Looking forward to seeing what you make with it.

[@mkegadgets4380]

Thanks for your positive comment please support me by subscribing to my channel if you have not. And check out my other over 100 videos on KZbin.

[@jhtvideo]

A great video with lots of practical well explained tips and techniques. You had an excellent explanation on the various ways to cut conduit with the pros and cons. It was also nice that you're presentations were short and to the point, and that you put your models on Thingiverse.

[@mkegadgets4380]

Thank you for your support with your positive comments and subscribing. Check out my other over 100 videos on KZbin. Most Wednesdays I put out a new video, I think you’re gonna like today’s thanks again.

[@atomicdmt8763]

excellent- is there a 1" conduit option?

[@mkegadgets4380]

Thanks for your comment. Please consider subscribe to my channel if you have not. Go to makerpipe.com. They just came out with 1 inch connectors.

[@keithguiste2659]

Thanks for a clear concise informative video I plan to build a solar array for my recumbent trike from EMT and use maker pipe connections

[@mkegadgets4380]

Thanks for your positive comment please support me by subscribing to my channel if you have not. And check out my other over 100 videos on KZbin.

[@keithguiste2659]

@@mkegadgets4380 yepp already subbed, will b looking at your vids

[@mkegadgets4380]

Thanks for your support. New video on most Wednesday, your going to like the next one.

[@p1dru2art]

maker pipe connectors ??

[@mkegadgets4380]

Yes you are right Maker Pipe connectors. Check out makerpipe.com website for more information. Thanks for your comment and please subscribe if you haven’t I appreciate the support

[@taylorphillips5118]

Conduit clamps. Great info. Thank you.

[@mkegadgets4380]

I’m glad you found my channel. Thanks for subscribing I appreciate your support I try to put out a new video every Wednesday.

[@yourtruckerfriend1584]

How can i get the drill jig and the foot /end cap parts please?

[@mkegadgets4380]

Thank you for your positive comment and continuing support. Please support my channel by subscribing. As mentioned there is a link in the comments to think of us so you can print your own. If you don’t have a printer quite a few libraries now have them.

[@SuperSpecialty]

I wish everyone who publishes vids would utilize your format i.e. don’t need to view their (uh, hem) “good looks”... if it’s neat, cool or awesome, who cares what you look like! Also, ahh’s & umhs are disenchanting. Yes, I’m subscribing... hope there’re the same format?

[@mkegadgets4380]

Thanks for your positive comment and for subscribing I really appreciate your support. My philosophy for my channel it’s about the projects not about me. Please check out my over 120 videos.

[@patrickmchugh695]

Erector set for old kids..... Dude you need gloves?!

[@mkegadgets4380]

You have to be careful wearing gloves when you’re cutting or grinding. If you cut your finger wearing gloves you’re probably gonna cut your finger off and it’s not gonna be a clean cut. With no gloves it’s a clear-cut and easier to reattach. If you don’t believe me ask my friend thumbs.

[@patrickmchugh695]

@@mkegadgets4380 I see that, but the way you were holding the drill (ream) and pipe, gave me the willies :)

[@williammunn1680]

where do you buy the fittings

[@mkegadgets4380]

Thank you for your comment. I mentioned in the video there was a link down below. But if you missed it here it is makerpipe.com. Please support my channel by subscribing if you haven’t.