Making A 2-Stroke Live Forever

Рет қаралды 299,049

Күн бұрын

Пікірлер: 263

@MrBassassinator 9 ай бұрын

Thanks for keeping the two stroke alive. I have a 1995 C115. Always run non ethanol and a good additive every fill up. Thing is a absolute tank.

@bellgab 10 ай бұрын

One thing that is VERY IMPORTANT is to use the proper type of marine grease for lubricants. Some types of grease for heavy equipment have aluminum in them. A saltwater environment with that grease is a recipe for seize up. Use marine grade grease.

@BornAgainBoating 10 ай бұрын

Great point!

@mikey27437 7 ай бұрын

Do you have any recommendations? Is Lucas Marine grease ok? Does Quicksilver really justify its price for fresh water application? Thank you.

@panzermagier 4 ай бұрын

I agree, now there are some specific grease from manufacturers, like mercury and Yamaha you can use without the aluminum that are specifically for the bushings lube. But in general any grease that doesn’t contain corrosive metals in salt environment will do!

@hankschrader149 10 ай бұрын

Aaron I'm very fortunate to have a shop near me that still works on 2 strokes. And....he used to be an OMC instructor! Had him troubleshoot my 120 Johnson looper, had cracked carb bases which I wasn't able to find on my own. Otherwise, I do my own maintenence and repairs thanks to your videos!

@jkg6211 5 ай бұрын

VERY well done! SO many people don't realize that they can do this job themselves, and it seriously makes the difference on the life of the engine. Good video!

@briancormier8189 4 ай бұрын

I have a 2 stoke merc, just bought the boat 2 yrs ago and been wanting to do maintenance on my own instead of bringing it to a shop. Thanks for posting these videos. These videos will be major help!

@NearbyCactus 11 ай бұрын

I laughed when you mentioned removing the oil pump on old Johnsons - I had a 1999 Johnson 50 & the fuel/oil pump failed not long after I bought it. Fortunately it failed by saturating the fuel, so didn't do any damage. It was $600 for a replacement pump or $60 for a straight fuel pump. So I was premix from that moment on. It was probably about 3 years old when that happened.

@hankschrader149 10 ай бұрын

That was the 1st project I did on my old 120 Johnson 2 years ago, VRO delete!

@100GTAGUY 8 ай бұрын

We would require a contract of zero liability and offer no warranty if you wanted to keep your injection pump at the shop I used to work at, nothing like your engines life blood being controlled by a plastic ring gear that shears easy peasy. Premix is the way to go, so long as your engine is getting fuel its getting oil. Too many dummies forgot to fill their injection tank or to connect the linkage to the throttle and then expected us to pay out the ass for their new engines for their negligence when they'd fry an engine in 10 minutes. Got to the point to where it wasn't worth the hassle, if you cant mix fuel you should buy a four stroke and neglect your oil changes that way instead lol. Mind you these were aviation two cycles so relying on a single failure point of a oil pump was a serious no go, all engine failures were inspected by the FAA and NTSB, we stood behind our work and were not found at fault due to negligence and or sabotage. Operator error or incorrect installation of the oil system were the culprits (we only did engines, no installs or engine removal, reservoirs were seperate from the pumps) Our most common failure was the pump gear shearing teeth or the central spline, or people neglecting to connect the appropriate linkages and lines to their reservoir. We offered deletes and block off plates for the rotary valve/waterpump/oil pump shaft at no additional cost as an incentive to go premix only, and would also return the pump to them as they are like a $180 assembly.

@ChrissyEis 7 ай бұрын

People are always crying about the fuel pump people are just to lazy to take a minute to see if you are using any oil I have a 86 mercury now for 5 years and I never had a problem I don’t recommend mixing 50 to 1 you will lose performance and it will be a lot more Smokey

@dallasdawson3674 11 ай бұрын

Rebuilt a 16ft fibreglass runabout over winter then fitted a 2006 model 115hp 2 stroke. Got to love these 2 stroke yamahas.

@DustinKeating-yk3vq 10 ай бұрын

I also have a 06 Yamaha 115 2 stroke it runs great I use only non ethanol gas and ring free at every full up keep my oil tanks clean and change my inline filter once a year I'm trying to make it run for ever

@Grgfkn3076 8 ай бұрын

@@DustinKeating-yk3vqI have a 90 Yamaha 2 stroke. Just started using ring free, are your carbs staying cleaner longer with the ring free?

@coastalcleaningandmaintena2884 7 ай бұрын

Yes yamaha imo made the best 2 strokes for boats and dir bikes. Anybody who is handy and can use a phone to research can revive them from the dead or tweak them to serious HP and torque!

@kingfish3066 11 ай бұрын

Hey Aaron really enjoying the series your doing on 2 strokes. I have been watching your channel for years and have learned so much from you . I think we should call you the professor 😁

@BornAgainBoating 10 күн бұрын

Lol :)

@ship_wreck_d3349 11 ай бұрын

I bought a boat with one of these a few years ago, so I’m loving this video series.

@michaellicitra7632 11 ай бұрын

It is very important to clean and lube the actuating arm of the engine oil metering pump and especially the spring in the shaft of the oil metering pump. This spring actually is a fail safe to provide positive oil delivery to the engine by turning the actuating arm full open position in the event of an operating linkage/cable failure.

@100GTAGUY 8 ай бұрын

Just run premix and delete the failure point altogether, because even redundant failsafes can fail. Double or triple redundant failsafes just get over complicated and expensive like airplanes, and boats already get enough heat for costing a ton of money. Excessive positive oil feed also makes fouling plugs when underway a likely possibility and could still leave you just as stranded. Nothing wrong with keeping up on preventative maintenance, id rather eliminate a potential problem before it can become one however.

@scottf.5472 11 ай бұрын

Great video for us with old smokers. Add a couple drops of oil to the starter gear shaft so it slings up freely

@sendeth 7 ай бұрын

I bought a boat a couple of years ago. I really didn't know anything about boats. I didn't want to destroy a new one so I bought an older boat to try to learn on. Knowing what I know now, I did overpay a little bit. But it's been a great learning experience and I've watched many of your videos. Thank you. I had no idea this was something to watch out for, but it looks like the one I got is already way too far gone. This point. I'm just looking to upgrade to a nicer boat now that I'm not a complete idiot

@coastalcleaningandmaintena2884 7 ай бұрын

I jumped in head 1st. I bought a brand new 18 foot with a 135hp inboard with a alpha 2 leg. This was 20 years ago. But basically a entry level boat now is the same. I ran that thing so hard only fresh water mind u. But for 10 seasons straight. I googled how to do a oil change and leg servicing (super easy 30 mins max) also how to winterize as it was always stored outside (even easier) never changed a spark plug, air filter nothing) did get 1 flat tire on the trailer in that time, cost me 117.00 CAD installed. The 4cyl engine was amazing on fuel. Total cost of all maintenance and fluids (not gas) wasnt more than 400 cad pesos over the 10 years and I must have put 500 hours per year on it at least. It never ever let me down and i saved many a boat that was sinking and ppl in distress. Sold it running the same as it always ran. Oh i did have to replace the bilge pump once. Got exact same one from crap tire for 29.99 and about 15 mins to install. Anyhow I sold it and only lost a few thousand dollars. Very impressive and i believe its still running around some lake or ocean somewhere. And now I can tow, backup like a total pro no matter what type of trailer or vehicle. And now I work on small tin boats and motors and can fix em and use them or trade up or down and its much more work than the brand new one i had 20 years ago but it taught me a great deal of knowledge. Now i can revive old outboards yammys being my fav. In a matter of a few hours usually. Just my story and now That im old n wise I run a cheap aluminum with 0 leaks thx to those new alumawelding rods and some Map gas and a free 80's yammy outboard i revived after sitting out in the elements for 7 years (took a pull cord and carb clean) and small wire up the water impeller and had it running the 1st day. But I ordered a new seal kit just for peace of mind. Also the old yammies could be almost doubled in power with about a $50 investment and 30 mins of my time. Perfect fishing machine and de stresser or weekend boat only free camping spots that are some of the best in the world. The boating community is amazing and its truly gave me some serious skills and knowledge as well as satisfaction of saving and helping people. Stick with it youll be glad you did. Anyone needs help or advice shoot me a message. B happy to try and help. Cheers

@1972mdc 11 ай бұрын

Your ketchup bottle trick is awesome! Remembered that from before and use it every time I need to top off

@dennismcfadden7066 3 ай бұрын

I have a 1994 Johnson 140 hp looper. Runs perfectly and the VRO works right. Love the power and pick up. Has 720 hrs and it gets full maintenance annually. On a Boston Whaler Outrage and it's a wonderful combo in Monterey Bay and down the coast.

@HM-ji7le 11 ай бұрын

Good information here thank you. I’m looking at buying a boat with a 1998 150 Mercury offshore two stroke outboard engine. I really don’t know anything about outboard engines. I was told that the engine had just been serviced about 6 months ago and his mechanic told him that the engine is in great shape

@steele09 9 ай бұрын

Find and buy the Service Manual for your boat (or vehicle or motorcycle) always first and foremost. Any maintenance or replacing broken parts are outlined with part #’s and instructions. Hopefully your Merc is treating you as good as my 1990 115 is! They’ll live forever if you take care of em

@nataliechicky1894 6 ай бұрын

GREAT VIDEO!!! I bought a 1987 cobia monte carlo 172xl with a 90hp yamaha 2 stroke off the original owner. Your videos are exactly what i needed. Thanks soo much!!!

@jafo4u508 5 ай бұрын

Go Premix brother you won't worry about that engine afterwards. That oil pump will fail and burn your engine.

@fishonkayakadventure 10 ай бұрын

you can use a heat gun to gently heat the metal around the areas where this grease is gummed up. DO NOT USE A TORCH!! and be careful about using heat near the grease seals at both ends.

@chiphill4856 11 ай бұрын

Nice motor transformation! This series is full of practical content. Key west must have sold a gazillion of those 1720 Sportsman models with a 90 Yam 2-stroke. Great power to weight ration on those motors. I notice you've picked up the cadence a little bit. Nice! ✌🏼

@r.waynejohnson9968 3 ай бұрын

One very important tool that I used extensively in restoring a 1989 Mako is a Dremel tool fitted with carbon steel brushes - I went thru literally hundreds of brushes, but they are well worth the costs. These brushes will brighten up the most corroded metal parts very quickly. They will make the most corroded S.S. screws look and function like new. ALWAYS WEAR EYE PROTECTION BECAUSE THE BRUSHES SPIN VERY FAST AND THE BRISTLES FLY OFF CONSTANTLY. Have handfuls of the brushes on hand - they pay for themselves by saving many hours of labor.

@r.waynejohnson9968 3 ай бұрын

they are also very good at cleaning mating surfaces of metal or thermoplastic parts.

@jrbuch 11 ай бұрын

I regularly use a 130 Yamaha V4 2 stroke. I've had the carbies rebuilt, decarboned, new fuel lines, water separating fuel filter etc. Also did water pump/impeller. Next up, poppet valve, and i'll re-do thermostats. Been running Salt-away through the motor, as it's throwing an overheat alarm at WOT. Hoping the salt away fixes it, if not thermostats and poppet valve. Don't really want to take the water jackets off.

@cmasters007 2 ай бұрын

I have a flats boat with an 2002 Yamaha 70 HP and that engine is a BEAST ! Maintain , Maintain , Maintain and it will last a long time .

@goaheadmakeourdayscooterpe9644 5 ай бұрын

One of the best motors I had was a Merc 9,9 from the early 80's I bought new because of a hp restricted lake I fished a lot but used everywhere else too. So easy to start by hand and could sit at idle for trolling for a hour and not even whimper when going to full throttle.

@davehaddad3229 11 ай бұрын

Any excellent DIY basic 2 stroke outboard maintenance - some great tips 👍. I have a 1999 Yamaha OX66 250 EFI on a 1988 2200 Pursuit - it keeps running well, reluctant to change to 4 stroke. With your tips it should be good for a few more years.

@DirtMcGert29054 11 ай бұрын

I got tasked with replacing the steering cable on that exact same boat , cut the old cable to pull it out , had to cpull the motor off to get the new cab,e in , was able to leave the rigging tube connected ... did it with a skid loader

@sam-y8t 11 ай бұрын

I'll be using this to open in the spring! Thank you so much!

@treatzfortruckerz3913 6 ай бұрын

I worked for 2 Evinrude dealers and a Nissan outboard dealer in the 1980s you gave a lot of great advice

@BornAgainBoating 6 ай бұрын

Thank you!

@gerardmccarthy2432 11 ай бұрын

I coat all my engines with fluid film as in dripping ....the smell of the cosmoline is additive. Excellent preservative and doesnt hurt the wires, on a 95 Merc 90hp.

@Freedomjunkremoval 9 ай бұрын

Great video man! I have this exact motor, I came on here to look for a video on the rigging tube and found this one instead. You did. Great job!

@BornAgainBoating 9 ай бұрын

Thank you.

@clarkbourgeois7661 10 ай бұрын

The Yamaha 90TLRB. One of the best engines I ever owned. Excellent maintenance video. I like the tie wrap on the low oil sending unit cap. Mine seeped oil so much I would only put a quart or two in at the time to keep the level below the rubber cap. Couldn't see spending $150 for a new sensor assembly for the rubber cap when the float switch worked fine for the alarm.

@BornAgainBoating 10 ай бұрын

The zip tie is a wonderful invention :) gotta love em!

@hankschrader149 10 ай бұрын

@@BornAgainBoatingamen brother! 🙏🏻 can't live without em'

@johnszoke586 9 ай бұрын

Thank you for bringing that. Up. I noticed that the engine was very hard to turn. I lube the push/ pull cable but not that one. It's going to do wonders I'm sure

@actioncorrosion87 29 күн бұрын

Just picked up a 115 Yammie for the project boat and going through it, good tips man!

@EngineNoise305 11 ай бұрын

Thanks! This is such a great series

@rpietros 11 ай бұрын

liking the 2 stroke videos. I own the V4 130 love that motor.

@richardgatchell2523 11 ай бұрын

You are very knowledgeable about outboards and boats so jealous but you have an amazing skill

@marshmellow3110 11 ай бұрын

I have a 1991 Monarch 16 w a 60 Mariner. Amazing how great that little motor has been. She is thirsty but runs like a top. Definitely burns more than my Xpress w 115 Yamaha 4 Stroke. lol

@davidreta3664 10 ай бұрын

How are mariners engine

@marshmellow3110 10 ай бұрын

@@davidreta3664 Just a rebranded Merc from way back in the day. My 60 has been great.

@davidreta3664 10 ай бұрын

@@marshmellow3110 I’m looking at a few they want 2500 92 60 to 93 60 3500

@Dustinscustoms 11 ай бұрын

I deal with froze up grease fittings all the time there’s a tool that you put motor oil in and you smack it with a hammer it’s for clogged grease fittings changing the grease fitting you’d be amazed when you think a pin is frozen and you change grease fitting and it works. Change the grease fitting and wiggle the motor side to side as somebody greases it. You won’t have to do much of those things you were talking about. I’m 99% sure, but sometimes you do you’re right

@BornAgainBoating 10 күн бұрын

I need that tool lol

@wmkess 7 ай бұрын

Good series on this motor. I was gonna add that I never trust nice looking (aka new) gear oil as someone may have put new oil and you don’t know what the condition of the previously drained oil was. If it’s drained may as well take 10 minutes and pressure test it to be sure. All that said I actually prefer to see black gear oil as that means it’s been in a while and has been used but is water free.

@dalbertvazquez1168 11 ай бұрын

Great video! Do one for merc 2 stroke please.

@Jerry-sy8rd 11 ай бұрын

Same

@dalbertvazquez1168 11 ай бұрын

@@Jerry-sy8rd still I'll like to see the same but with a Merc 2 strokes.

@rollingrecords9019 11 ай бұрын

Your always on my wavelength thanks brother awesome video 💯

@sak4550 10 ай бұрын

I’m glad you mentioned the fact that grease does not compact. I was going make a comment on that until you got to the water impeller housing bolts

@enesarar 11 ай бұрын

Thanks mate. I have some tasks waiting for me now

@dwightyoung2269 4 ай бұрын

A pump up sprayer with plain water would work well on rinsing and be more precise and get in crevices .

@bubbleobill267 11 ай бұрын

Spend the bucks on a new head gasket. Pull off the head and get all of the crud out of the cooling galleries. I did to mine and was surprised at how much stuff had to be chipped out.

@hankschrader149 10 ай бұрын

Yowza! I'm afraid to look at mine 😂

@nygardenguru 9 ай бұрын

Lucky all the bolts came out

@bubbleobill267 9 ай бұрын

@@nygardenguru No problems with the bolts, they all came out pretty easy.

@NeverEnoughPyro40 8 ай бұрын

@bubbleobill267 Or you can just spend a little time and flush your engine while washing your boat down after every use, There is absolutely no reason why any engine should look like that! Motors like that usually belong to lazy incompetent owners who lack even the most basic knowledge when it comes to boat maintenance!

@bubbleobill267 8 ай бұрын

@@NeverEnoughPyro40 If it’s a new ( old ) motor to you sometimes it has to be done, I’m all for flushing after every use too. Maintenance is key in my books.

@dopefish93 7 ай бұрын

Tip for the rusted pivot pin. If you think that it might be full of dried up grease you can push kerosene or thinner through the grease nipple. Leave it to dry for 24h and you are good to go.

@BornAgainBoating 3 ай бұрын

That's a great tip, thank you! Never heard of that :)

@waynestanton467 9 ай бұрын

I have a 2008 90 2 stroke. Just hard to start after sitting a few days. After that you can look at it and it starts. New primer bulb pumped up super tight. Checked and cleaned the carbs and fuel enrichment system. Don't understand why yamaha decided these engines didn't need a choke. I'm thinking about getting a snowmobile plunger primer and taping into fuel line and installing a Tee where the enrichment host is attached. Goods video.

@BornAgainBoating 9 ай бұрын

Good luck!

@jimv1484 11 ай бұрын

One heck of a video! Two thumbs up!

@fastfed 11 ай бұрын

I do not save many videos but this is one I will be doing soon. thanks for all the stuff I had no clue about lol

@Al-ix5um 11 ай бұрын

Great video. Many thanks.

@LordDarthBaiter 11 ай бұрын

Rebuilt my ox66 recently and now I see I need to lube some areas I missed. 😮😊👍

@AGZ-dt6pg 7 ай бұрын

Great video keep the 2 stroke Yamaha content coming! New subscriber

@Real.Alpheus 7 ай бұрын

Could you make a video showing where to add another grease fitting in the steering tube or how to remove and replace steering tube bushings? Thanks.

@BornAgainBoating 3 ай бұрын

You just need to turn the engine to one side or the other and then towards the top about 3 inches below the steering tube top, drill the hole in the middle where you can thread a zerk in :)

@r.waynejohnson9968 3 ай бұрын

Had to open up the thermostat housing the second time because you forgot to replace some of the parts ? Always have on hand a handful of small plastic bins in order to store and segregate your nuts / bolts / and small parts. You'll never have the problem of forgetting to replace something.

@ipodaholic09 11 ай бұрын

The yamaha auto oiling definitely does fail to no oil supply. I have the seized engines and blocks with thrown rods to prove it..... Just as bad as the omc vro system

@JohnSmith-pl2bk 8 ай бұрын

Could that be that the owner has not lubricated and checked/replaced the spring that actually IS the failsafe spring to give wide open oil supply when/if the oil pump "fails" internally?

@sha6mm 10 ай бұрын

Man you do a lot more than Me. I just grease it every year, change lower unit oil, New plugs, and change prop and grease shaft. And was with lime away, and Gunk And Armor all rubber. My 2004 30hp Johnson looks new.. This is all I have done on my Boat Motors for the last 40 plus years but I am in fresh water.

@JohnSmith-pl2bk 8 ай бұрын

Have you never changed your water pump impeller?

@jamikomodo 5 ай бұрын

Thanks! That was informative video. I didt know that there was a grease plug for a steering. Mine was so dry. Thanks! 👍

@macmacguyver4094 5 ай бұрын

Unfortunately, I don't have a grease fitting at the bottom of my engine, only the top. So, after seeing this, I'll drill a hole to clean out some old grease, then a zerk fitting.

@hankschrader149 10 ай бұрын

Long live 2 strokes Aaron!

@nikademus00 11 ай бұрын

Great informations ! keep going !!

@marklaw2845 11 ай бұрын

Great series, very informative 😊

@thecableguy1128 11 ай бұрын

I have a Suzuki df140a with 86 hours on it. I have been very diligent with the maintenance of it. I flush it every time I use it with salt away. Now salt off. I changed the internal anodes and they were full of corrosion and salt. It really surprised me how much it had inside of the water passages. I wonder how much worse it would be if I didn’t use the salt away. I changed all fluids every year no matter if the engine oil change timer light is on or off. I really want to see what happens when you run the salt off through the engine.

@47plymouth 8 ай бұрын

The plated shell on NGK spark plugs don't need anti seize. In the small print it is not recommended.

@aaronellinger2662 4 ай бұрын

Great job creating this video. Coherent and condensed. Thank you for sharing your knwoledge.

@robmitchell3633 11 ай бұрын

Just replaced my tiller arm pivot last year on my 96 yam 150. Corrosion on the steel arm was bad.

@anthonymannarino3376 10 ай бұрын

I just had to change my oil tank sensor and harness. The alarm where off on me .

@Massiverobsfishing 11 ай бұрын

Why don't you use degreaser to soften up the old grease and even help clean off the other bits?

@michaelhoneycutt7138 9 ай бұрын

Spraying with WD-40 works as well breaking down old grease to free up for grease to flow.

@JohnSmith-pl2bk 8 ай бұрын

There is a clue there...WD40 it is not a lubricant..it is the exact opposite! It is Water Dispersant formula 40 (got it right after 39 attempts!) By all means use it to clean things.... Use it to get rid of water. Don't use it as a lubricant for anything. Use a lubricant for lubrication Use a silicone spray as a surface protectant for cleaned surfaces...liberally on any outboard. Horses for courses.

@TheDoug9901 11 ай бұрын

Heat or take the pump off the grease gun and pour some oil and try pumping that in with heat.

@outdoorengineering3080 11 ай бұрын

love the channel and everything that is in the video except for him saying remove the oil pump, I know where he gets his misconception from but ever two -stroke with a VRO that has seized or blown up that I have seen has indeed not been caused by low oil or inadequate oil flow they were all caused by some other less obvious reason. Again love the channel but just wanted to through that out there.

@100GTAGUY 8 ай бұрын

Man i got spoiled with my engine cleaning setup at the shop, would've degreased the whole thing from the get go with the solvent wand and dried with compressed air. Then proceeded to inspect, tear down as needed for further inspection, and relubricate. With that old grease id lubricate before and after each outing for a few weekends, and then periodically biweekly. Lube is cheaper than parts. I prefer LPS 2 or 3 for preservative coatings, its good stuff and im not here to knock other brands but i prefer it for the smell honestly. Personally ive been mixing fuel since I was 5, my dad wouldnt let me start the dirtbike until i knew how to mix fuel and only fill it with the jug labeled "32:1 PREMIX". Id rip the oil injection right out and just add the appropriate amount of oil for how much fuel i pumped. Id rather premix than risk a failsafe fouling my plugs and still stranding me lol. Im a firm believer of if you can't mix gas you have zero business owning a two stroke, thats my pedanitc generalized opinion on the matter and not a dig at you.

@BenKimim1453 6 ай бұрын

Hey Aaron, have these 90hp 2 strokes changed at all, example is a 2004 year the same as a 2014 year model, awesome vids mate thanks

@BornAgainBoating 6 ай бұрын

Very minimal changes if any at all, they are bullet proof! lol

@jackofmosttrades9127 7 ай бұрын

I have a ‘99 OX66 150 and the service manual shows several anodes under the cylinder head. Have you ever had the remove a head a replace those anodes?

@BornAgainBoating 3 ай бұрын

Depends on where you use it, saltwater, not a bad idea to do so, but at this point in time, you might be opening a can of worms pulling those bolts

@Ajaxaxxess 5 ай бұрын

So cleaning it, greasing it, new plugs and impeller and it will live forever?

@coleswagert3767 11 ай бұрын

I've got a 90s model yamaha that recently ate something on the bottom cylinder. Would a rebuild be worth it or get a new motor

@BornAgainBoating 11 ай бұрын

Depends on a couple of things. Obviously price and availability of stuff. If the rest of the engine looks good, like the lower unit, the trim unit, and other parts on the engine, like most of them are in good shape and are going to last, that is a check for the rebuild. Is there someone around you or are you able to do the rebuild? Depending on if you or someone you know can do a rebuild, how long will it take, how much will that cost, that factors. Or is there the availability of the parts to do a rebuild? Or maybe you could find a used powerhead or a new or remanned powerhead? What would that cost? And how long would it take? Based on that, those will get you to a pretty good idea of what it would cost, and if it would be worth doing it. Then compare that to a new engine, and how long it would take to get it done. Also, what's your money look like? If you got the money and don't want to mess with it, new, if money's kinda tight, but you got most of the other stuff for a rebuild, rebuild it :) 90's Yamahas are super reliable, but, they are getting older and older and parts start to fail often with this type of age, so, lots of variable here lol hope this helps

@gregfeldman6818 11 ай бұрын

Great Answer - You are a Boater’s Best Resource! One other possibility to consider would be to find a used engine with a bad lower end or seized steering.

@mikencrew8885 11 ай бұрын

Love it. Thanks brother

@minniesfishies3024 10 ай бұрын

In dropping the lower unit of my 2 stroke 25hp Yamaha, the trickiest part is detaching the shift linkage. Beware!

@KirkAllenOutdoorAdventures 8 ай бұрын

Great Tips, Thanks for sharing.👍

@rbledsoe61 8 ай бұрын

New here. Will an ultrasonic tank help to clean the Tstat housing?

@BornAgainBoating 25 күн бұрын

Yes it can

@Ruzwa 5 ай бұрын

A bit of a contradiction on the impeller: "I would not change this, but I'm going to because I'm here" ;)

@BornAgainBoating 5 ай бұрын

I never said I was smart lol :)

@Bodie193 9 ай бұрын

I would love to see someone invent a Fuel Injection system for the 115 & 130hp 2 strokes engines. I would buy it now, carbs burn twice the gas as FI engines. My 130hp is 24 years old and going strong, so I want to keep it as long as possible. The price of a new 4 stroke engine is a bunch and budget crusher! Thanks for the detail instructions on your video.

@BornAgainBoating 9 ай бұрын

You're welcome

@SherryGentry-r6e 9 ай бұрын

Great videos, I’ve got a 96 2stroke 40 hp Mariner & can’t find a video on the how too’s to get the engine cover off, can ya help?

@BornAgainBoating 9 ай бұрын

Hey! Rose here, helping Aaron with comments. What a great topic! It's headed for our podcast feature list. If you haven't listened yet? Subscribe here: www.youtube.com/@TheBoatersPodcast

@slabbusterrtr7690 10 ай бұрын

One word for making the motor last longer marvel mystery oil ive been using it for years since the 80s never any carb issues not one great for fuel pump and cylinders to

@justinlowe5880 10 ай бұрын

Hello. Love your videos. They’re great! I have a question if you don’t mind offering your expertise. I have this same motor. Under load mine does like 10mph full throttle, in the water. Out of water it throttles high and normal. Have any idea what it could be?

@BornAgainBoating 10 ай бұрын

Hi there! This is Rose. Thank you so much for your comment! Unfortunately, I don't have the answer to your specific question. We find it's best to address these inquiries one-on-one. That's why we've introduced a channel membership, where we discuss these topics weekly in live sessions. If this sounds appealing, simply click the "Join" button next to our channel name. Much appreciated!

@danieln3999 11 ай бұрын

Any tips for a 60tlrz with a persistent overheat alarm despite new impellers, new water pump housing, a muriatic acid rinse through the water jacket and even a full disassembly of the water jacket? It is clean as can be and is a fresh water motor but will alarm if let sitting at courtesy dock or when idling after coming off plane. Tell-tale is not strong at idle but it never has been and have read yamahas have notoriously low water pressure at idle/neutral.

@JohnSmith-pl2bk 8 ай бұрын

Check the water intake for the cooling system... if water can't get in at idle...at speed the speed actually helps force water in.... clear all the passages into the pump...check wear on the pump housing?

@BornAgainBoating 10 күн бұрын

Hopefully you've figured this out, but another thing too look at is the water coming out the exhaust as well as top of the water tube, if you have an issue with the water tube the water volume will be low. If it has a tell-tale it's moving at least some water. I'd also check the actual temp of the engine with a temp gun to see what is getting hot, how hot is it getting, and where :/ hopefully this is done though

@danieln3999 10 күн бұрын

@@BornAgainBoating I put a temp gun on it a while back trying to double check the temp sensor while it was installed and not just the "stove top test." I don't think it is actually getting hot. The tell tale water is not hot. If I run for a an extended period of time, then come off plane and idle (like make a long run to a duck spot then idle into a slough or backwater area or set decoys) it will usually go off. Of course then you have to give it enough throttle to push more water through it but not so much you hit the rpm limit with it limping. Just a royal pain in the butt at times.

@WildTex-m9u 5 ай бұрын

About 5 years ago I got an old 89 150 Evinrude XP. The first thing I did was throw the VRO oil pump in the trash. I premix my fuel with no issues. What oil do you guy recommend for old Evinrudes? Is synthetic blend good?

@BornAgainBoating 5 ай бұрын

Most outboard oils are all a synthetic blends so for sure they are good. I'd say to keep doing what you have been doing for the last 5 years, seems like it's working great! Normally we tend to recommend branded oil, Evinrudes get Evinrude, Yami's get Yamaha's, Mercury's get Mercury's. RevX oil makes a really good oil too though.

@WildTex-m9u 4 ай бұрын

@@BornAgainBoating Thank you Sir. This is what I’ve been wondering about. Spent the entire weekend out on the lake and the old Evinrude ran great.

@4040pmora 9 ай бұрын

Great video as always. Do you have any suggestions for spark plug sockets? My sockets will not fit my 4-stroke Suzuki

@BornAgainBoating 9 ай бұрын

@JohnSmith-pl2bk 8 ай бұрын

Find a socket that does fit!

@gennaroraggio3710 11 ай бұрын

Good video but from my experience owning two strokes with oil injection,the oil pump commonly fails on these engines especially Suzukis.The best thing to do is bypass the oil pump connecting the hoses together and running the engine 50:1 gas to oil ratio.All oil injection does is give the engine less oil at Idle and low speed creating less smoke,also making it a leaner fuel ratio.Failure of the oil pump if not noticed in time(light off)can be catastrophic to the engine.Yes,more carbon will develop on tops of pistons and inside of cylinder head but no matter what if the motor came with oil injection or not,the cylinder head should be removed and cleaned of carbon periodically along with a mild wire wheel mounted to drill to remove carbon off of top of Pistons, reassembled with new head gasket.The cleaning is what will assure very long engine life.

@SCDeerAddict 4 ай бұрын

The yamaha outboards don't send oil through the carbs to gunk them up, it mixes the oil on the backside of the carb, the mechanical oil pumps rarely fail on the yamaha, keep it lubed it will last forever, and your carbs won't need cleaning all the time like if you premix and let it sit for awhile.

@JamaicaBayRat 6 ай бұрын

I put 5000 hrs on this motor Sold it running like new

@billmurphy604 11 ай бұрын

😆 I just had to fix this... no chance of adding grease. Had to pull powerhead and disassembled. Turns like butter now.

@Mike-sl1wd 11 ай бұрын

I'd love to see a video of how that is done...hint @bornagainboating

@billmurphy604 11 ай бұрын

@@Mike-sl1wd yeah, a video would have been nice. I had to use a lot of heat and a big dead blow hammer. It was scary winging it!

@kevinjamison7240 10 ай бұрын

What kind of silicone spray to like to use? You mentioned crc but that can you had was crc I thought? Can you provide a link of what you like?

@JohnSmith-pl2bk 8 ай бұрын

CRC is a company that manufactures many types of lubricants and sprays. You just need to go to say an auto supplies store and choose the right one. They even make a lube spray for marine environments called 2.66

@BornAgainBoating 22 күн бұрын

amzn.to/3VLHVIT

@solidtangent9953 11 ай бұрын

I always heard those motors are great engines I picked up a 75HP going to be putting on a skiff I have cant wait

@BostonMA781 3 ай бұрын

Realistically - what speed should an older (2007) 90hp 2 stroke reach at full?

@BornAgainBoating 3 ай бұрын

What do you mean speed? You mean RPM, roughly 5400, 5500 is the max, speed is totally dependant on prop and boat set up

@MP-qn1jw 11 ай бұрын

Awesome video!!

@smacinskyjr 8 ай бұрын

I have a 1991 Mercruiser 150 on my 1991 ProCraft 180 Combo. The boat has very low hours (less than 200). Would you be able to do a how to on a similar engine? Right off the bat to me there are differences between the Yamaha and the Mercruiser.

@JohnSmith-pl2bk 8 ай бұрын

Look for those grease fittings on the Merc???

@earlraines6152 11 ай бұрын

Hello I am doing a 200hp Yamaha some things your doing just going. A step more and the engine. I got a S200txrx and I pulled the exhaust cover off and had 12 bolts break on me any suggestions how to get them out

@JohnSmith-pl2bk 8 ай бұрын

By now I presume you have drilled and Ezy Outed them all?

@earlraines6152 8 ай бұрын

Yes I did and it ready to be put back together just waiting on one gasket

@JohnSmith-pl2bk 8 ай бұрын

@@earlraines6152 Nice....just in time for spring/summer. Safe boating (got a Yammy "kicker" to use as an emergency motor?)

@mikesolns1364 11 ай бұрын

In general are early 1990s 2 stroke 225 Yamahas worth keeping alive? I got twins that came with my boat and have had some issues with them. Wondering if in general it's worth it to continue to help them live?

@JohnSmith-pl2bk 8 ай бұрын

They will last a very long time if you keep the maintenance up...as per this vid. What has been the major concern with your setup?

@mikesolns1364 8 ай бұрын

@@JohnSmith-pl2bk My current issue is that after I run them for say 40 minutes, they start building a whitish blue milky residue on the throats of the carbs (more so on the lowest ones) the kind I've read most say is due to humidity, condensation, etc. After a while it seems it builds so much that one engine, or the other, will die and will have hard starts, or not start again, until I get to the dock and clean them off that residue. I'm using new fuel filters, new fuel water separators (the old ones had water in them, but checked the new ones last time it happened and there was no water in them. I also added gas conditioner to my ethanol gas. I also had just cleaned all carbs before last time it happened and drained the bowls, after use, hoping it'll do them some good. Each engine has its own dedicated tank. So I'll go Monday to see how they do this time, hoping that with repeated use it'll stop happening?

@JohnSmith-pl2bk 8 ай бұрын

@@mikesolns1364 Look at the air passages from the cowling intake to the carb intakes. Look for a spray of water from say the thermostat housing/pee hole..you can't see it under the cover of course when the engine is running. If that residue is there in the throats BEFORE the jets it's being brought in with the air,,,,not the fuel.

@mikesolns1364 8 ай бұрын

@@JohnSmith-pl2bk Awesome help. I'll check that. I suspect also my cowling seals are letting water seep in, as they don't look tight enough. And when I'm in the water running them, most of the time I see the pushed out water around the engines, above the cowling seals level. Could that be causing it too? If yes how does that even get addressed? Thanks in advance

@BornAgainBoating 10 күн бұрын

Hopefully you have this figured out by now, but yeah, with maintenance they should be good reliable engines, fuel thirsty suckers, but reliable. Just reading some of the comments, looks like that was the way to go, if you have moisture residue on the throttle body intakes, that moisture is from the air somewhere and somehow. Could be cowling seals for sure or hole somewhere else or a leak in the cowling. If the engines are mounted too low, that could be an issue, so mounting height could help if they are incorrect and too low :) hopefully you've fixed this already though ;)

@markdimaio8396 11 ай бұрын

The engine tilt lock lever on my 90 is very difficult to move on tried PB Blaster and WD 40. Didn't do much

@BornAgainBoating 11 ай бұрын

Ouch, yeah, you can try kroil, but you might end up needing heat, or trying to take the thing apart. Or you could also always just leave it alone and whoever has to work on it will just need to use a block of wood to lock the engine up to work on the trim lol :)