I like the fails, because it can lead you to other inspirations. So nothing is ever wasted.
@deepashtray56052 жыл бұрын
Cool. Where one lays on top of the other you could try to simply glue the bisqued pieces together, should hold long enough to get the glaze applied. The glue would burn off. Just have to make sure the glue doesn't act like a resist, and that nothing would shift after it does burn off. Could glaze them right on the shelf with a layer of newsprint underneath that you could slide out when dry, minimize carrying it around. Have you thought about using a marble to lightly press an indentation into the wet clay where you want them to stay? Not so much that it would be noticeable, but enough to keep the marbles from rolling off. Last thing. This would be cool to try, I think..... Take a bouquet of noodles, probably on the shorter scale, and set marbles in the forks. Maybe go with more of a narrower vase so the branches fit a bit more snug to hold the marbles in place.
@JustinsMakery2 жыл бұрын
Thanks for the good ideas! Got me thinking..
@phylismaddox48802 жыл бұрын
You know, those bisque rods would be great as diffuser sticks. A straight weave (lattice) is probably your best bet. It's easy to do using guide sticks since you can't fold back the clay. Fancier but easier in clay would be twining the weft. Twine both the weft and warp and the marbles won't ever move!
@jimruel21212 жыл бұрын
Love your channel and how your mind works...keep up these experiments!
@peteburton-davies10812 жыл бұрын
Could you just bisque the rods as separate pieces then only glaze the top layer. You’d only have glaze on either the horizontals or verticals depending on which direction is on top but you’d be able to glaze the whole rod and I bet it would still be a nice effect. I bet the glazed rods would stick well to the unglazed ones still.
@patspotpage2 жыл бұрын
I wonder if you spray your lateral strips with vinegar before you lay your horizontal strips on and squish them in would that help them hold together.
@barbarac41382 жыл бұрын
If you run a roller over the pieces as they lay on top of each other it helps them to fuse to each other. Or press slightly at each cross point to join them. Like your finished vase piece
@barthanes12 жыл бұрын
Great save with the unintentional ceramic sticks. Maybe cut holes in a sheet to melt the marbles in. Sculpt the woven look into a sheet with holes.
@jojorengers5368 Жыл бұрын
Those "breadsticks" are really beautiful! Very good "idea" for a mistake 👌🏻
@momadhis6 ай бұрын
Ground bisque ware .... turned to grog for clay Weave over clear plastic (canvas). Make slab with marble size holes. I think all other comments are even better. Love your experiments, makes me think of possibilities.
@leobrent79262 жыл бұрын
How about making a thick piece of plaster (kind of like a thick tile) and then cutting on it a square pattern with an old saw blade maybe on the table saw or a circular saw if you have one, then build up four walls with more plaster and use slip on that mold to get your square pattern marble holder. At least that’s what I would try.
@lilbit759 Жыл бұрын
Mistake wasn't a mistake after all. Nice decor pieces😍
@brefni162 жыл бұрын
Lay out the bottom layer of coils & then give a good spray of water. Put a coil in place for the top, hold both ends, and ever so slightly move back and forth a bit, creating a micro layer of slurry. Then press down. OR lay out the bottom layer, good spray of water, lay out the top layer , then take a small finishing nail, pierce the center of each joint. If you like the look, keep it as is. If not, fill in hole with slip trailer,
@genboomxer2 жыл бұрын
Started typing a similar answer. Yes, what you said.🙂
@micheledickey40662 жыл бұрын
I sooo love your optimism!! Lol.
@nian602 жыл бұрын
Maybe pour slip over the rods somehow, to make them stick together? You would have to put it on something that the slip can drain through, and then move it to the kiln without touching the rods or taking them off the thing. A barbecue rack, maybe?
@kathykempson22522 жыл бұрын
Would it work if you weave your extruded project? edit: OH, never mind I now see you thought about it. I have woven similar pieces and they stay together nicely.
@fredrikjohansson2 жыл бұрын
An experiment I have been thinking about is quartz crystal. To embed in the clay and see if the transparent windows are kept there after burning.
@penniewyatt9391 Жыл бұрын
I tried it and it fired off completely. 06.
@erincampbell151510 ай бұрын
Not sure what you fire bisque to, but If you are bisque firing at 04, use low fire glaze on the greenware joins. I use clear on greenware so my disabled students dont paint glaze on certain areas of pieces. After bisque, Then use a colored low fire glaze to finish off the piece. Then if you are firi g marbles at 014-015 it still shouldnt disturb the lowfire glaze.
@ankhpom92966 ай бұрын
In bisque the marble will soften and partially melt. At cone 5 or 10 it will liquify. Take it from there.
@rickwise62592 жыл бұрын
Justin Did you make that extruder? Looks great!
@shelleydoxtdator7537 ай бұрын
Are marbles food safe? I love how they blend
@yudeok4132 жыл бұрын
This channel is my animal spirit
@nonya47542 жыл бұрын
Can you cut square holes out of a slab to fake your woven pattern?
@vickibarrycoppard83362 ай бұрын
you could try a raw one glaze fire that should stick it .
@otterwench2 жыл бұрын
serrated, lay first layer, paint contact area with slip, lay top layer and roll each back and forth a little to spread glaze into top cane serrations. probably better to paint the slip a few canes at a time.
@chancerichardson91102 жыл бұрын
Use steal wier to weve between the edge noodles
@jontompkins1844 Жыл бұрын
Was any one else like "sweet Jesus he just destroyed some beautiful antique marbles"? I'm sick.
@lyndafjellman3315 Жыл бұрын
They look like the marbles I've purchased at the local dollar store