Making Camshaft For Racing | Extreme Camshaft | Camshaft Lathe #lathe #racing #otomotif #jupiter #LATHETECHNIQUE The following is the camshaft lathe process to add open and close valves on racing engines
Пікірлер: 66
@honkie2474 ай бұрын
I doubt the cam you modified is the cam that was in the engine when you started the bike. You can't eyeball opening and closing ramps or the ellipse on the base circle. Not to mention that you ground off the hard facing on the original cam. Nice slight of hand tho.
@DaveMcLain4 ай бұрын
Cam cores are hardened before they are ground so the heat treat extends pretty deep from the surface. The problem with this freehand method of modification is that there is no way to duplicate the results without a master.
@joepkortekaas88132 ай бұрын
It is simply one camshaft destroyed!
@honkie2472 ай бұрын
@@joepkortekaas8813 And another example of CLICKBAIT on youtube.
@joepkortekaas88132 ай бұрын
Splendid! One camshaft destroyed!
@leonardofabiotorrescamacho784411 ай бұрын
Hola , no se qué idioma hablas , pero me gusta tus modificaciones , me gustaría me enseñarás a usar el transportador con el que tomas las medidas en el rotor o volante magnético y como logras tantas RPM al acelerar en un motor tan pequeño 😮 saludo desde Colombia
@soerif25197 ай бұрын
Bahasa indonesia
@abuelitoyukillo43668 ай бұрын
Gran máquina, gran trabajo, gran idea, y gran , gran , gran MAESTRO.
@ddvan59478 ай бұрын
Itu alat papas cam shaft bikin sendiri atau beli bang,,rapi bgt alatnya.saya punya alat papas cam seperti itu tapi hasilnya untuk papas kok nggak bisa rata ya,,padahal saya beli di salah satu bengkel balap daerah sini
@bhagasasi4255 ай бұрын
Orang bule ditanya Indo mana ngartos 😂
@АлександрНихтферштейн8 ай бұрын
Это не спорт.распред.. у спорта перекрытие больше и фазы шире.. а тут.. на хх норм работает... А на спортивном распредвалу холостые обороты ужасные.
@antoniogrullon740424 күн бұрын
wbat is the machine model ?
@progaragechinskiemotorki Жыл бұрын
super maszyna :)
@c__TattinhNhi8 ай бұрын
Tolong izinkan saya bertanya kepada Anda. Durasinya harus sesuai dengan setiap rasio kompresi yang berbeda-beda kan?
@IvanWijaya-ze5rj11 ай бұрын
Very precisition
@SCus_lipetsk Жыл бұрын
Уменьшил подъем клапана? Это же приведет к уменьшению наполнению цилиндра , падение расхода и мощности. Или увеличили вазу открытия клапана?
@lathetechnique2279 Жыл бұрын
Menambah vas pembuka
@SCus_lipetsk Жыл бұрын
@@lathetechnique2279 🔥🔥🔥
@user-zy7pe9cl2e Жыл бұрын
да нет увиличил я так на днепре зделал
@SCus_lipetsk Жыл бұрын
@@user-zy7pe9cl2e за счёт чего? Он же на токарном высоту снял, и компенсировал стачиванием задней стороны. Подъем остался прежним. А вот фазы сместились на более раннее открывание и позднее закрывание
@user-zy7pe9cl2e Жыл бұрын
@@SCus_lipetsk я высоту кулачка неснимал только базу таким образом и фаза шыре и высота рабочая выше
@nghiepnguyen47028 ай бұрын
machine good
@BabakDoroudi Жыл бұрын
عالی
@edgarferreira3497 Жыл бұрын
Cuanto cuesta una máquina de esas usada y donde la venden por favor 🙏 gracias
@oky73462 жыл бұрын
Andalan🔥
@lathetechnique22792 жыл бұрын
Maturnuwun mas
@luisbatista597 Жыл бұрын
💪💯😎
@ojahlala13 Жыл бұрын
nice lift 8mm. here we call it sleep cam. because use rocker arm ratio.
@lathetechnique2279 Жыл бұрын
yes that's right, I found the ideal lift at 8mm with a large duration to form a perfect camshaft profile so that there is minimal floating, the final result is very surprising with very large power
@australiandirtbikeracing2108 Жыл бұрын
@@lathetechnique2279 do you guy's race these bikes, if you do i would love to see a video. Thank you for sharing the video👌👍
@lathetechnique2279 Жыл бұрын
@@australiandirtbikeracing2108 yes of course, I will make it in the next video
@arkanfatih87727 ай бұрын
❤
@alfianr8435 Жыл бұрын
Sering bikin noken punya MX king mas
@lathetechnique2279 Жыл бұрын
Iyaa mas noken random juga , cuman kalo request angka pengerjaan nya manual seperti yang di video , drag,roadrace,cross dan korek harian kami mengerjakan juga ( bergaransi )
@bowowibowo6401 Жыл бұрын
Kuat sekali torsi nya
@lathetechnique2279 Жыл бұрын
Kebanyakan camsaft jupiter kalo di rubah menggunakan roller dia akan mudah floating(gas segar yang terbuang membalik) ,nah disini saya mencari agar minim floating dan menghasilkan tenaga yang besar
@fiktorrosyidi7752 Жыл бұрын
@@lathetechnique2279 hooh.. Pake roller akan menambah berat templar alhasil kelembaman dan momen inersia akan bertambah.... Mudah floating
@lathetechnique2279 Жыл бұрын
@@fiktorrosyidi7752 mungkin yang anda kira berbanding terbalik ketika sudah menemukan profil yang tepat , coba perhatikan pada akhir video (motor hidup) ketika di rpm tinggi minim sekali gas yang keluar menandakan sangat kecil sekali terjadi floating
@lintangprayoga8516 Жыл бұрын
pengaruh in close jika karburator nyembur
@agasagas8037 Жыл бұрын
Bng klw bikin mesin bubut nya habis dana brapa yg kaya gitu
@lathetechnique2279 Жыл бұрын
Kalo sekrang kurang lebih 5jt , tapi kebetulan alat itu saya jual Bang
@user-gk5tc8pq3z11 ай бұрын
Фаза перекрытия клапанов не изменилась почти! А значит и толку мало от увеличения открытия клапана
@markderzhec70978 ай бұрын
Перекрытие надо было увеличивать ? То есть чтоб кулачки ближе друг у другу были ?
@user-ks1zi1qc8q7 ай бұрын
Да изначалная форма почти не изменилось у этого вала не было острого угла изначально
@markderzhec70976 ай бұрын
Вы можете по образцу перешлифовать ?
@michaeljohnfillartos9370 Жыл бұрын
SanA all naka racing
@theo_korner Жыл бұрын
125cc or smaller?
@lathetechnique2279 Жыл бұрын
135cc
@galihpratama567 Жыл бұрын
Daerah mana om
@lathetechnique2279 Жыл бұрын
Jawa timur banyuwangi
@pierremathonnet95918 ай бұрын
Petit ou gros moteur, les techniques restent les memes.
@jessewoody5772 Жыл бұрын
I'm surprised it ran.
@lathetechnique2279 Жыл бұрын
Thank you brother
@needmoreboost6369 Жыл бұрын
Why?
@lathetechnique2279 Жыл бұрын
@@needmoreboost6369 which part are you asking?
@needmoreboost6369 Жыл бұрын
@@lathetechnique2279 I’m impressed with your machines simplicity and efficiency,nice work! Jesse woody comment said “I’m surprised it ran” but I said why as myself I use a reduced base diameter re-grind cam with good results
@thongdo7338 Жыл бұрын
Mài kiẻu nầy chắc kêu điếc lổ tai luôn
@lathetechnique2279 Жыл бұрын
Benar sekali
@yunkchannel586 Жыл бұрын
Ada kontak wa nya
@lathetechnique2279 Жыл бұрын
Ada pak di chanel saya
@lathetechnique2279 Жыл бұрын
Kalo gak tau boleh yang ini 082334359465
@helmutblumberg9087 ай бұрын
The cheapest and most unprofessional tuning doing for a camshaft. Engine damage is already inevitable. The most important thing is the starting ramp, and that is ignored and destroyed. Simply rubbish!!
@javeriaqavi1955 ай бұрын
I stead of doing all this bullshit, he should have grinded the rockers or loosen tappets.