Making Homemade Lathe Milling Attachment For Compound Slider And Tool Post

[@oficinacupimdeferroalysson4048]

Trabalho De Mestre My Friend directo Do Brasil Paraíba 🇧🇷🇧🇷

[@mr.ranyhomemade2466]

Thank you

[@ferriswhitehouse1476]

You're an inspiration. I hope I can replicate your work, thank you for sharing!

[@1crazypj]

That was actually a neat way to fabricate a 'T' slot. I was thinking you may need to modify bolt heads so they can't spin in the future when things wear in. 220mm is a big diameter for a small lathe, I couldn't do it as my lathe doesn't slow down enough. (500rpm is slowest it goes) I have used an angle grinder bolted in place of tool post to grind larger diameters around 185mm

[@mr.ranyhomemade2466]

Thanks for your introduction it very hard for me everything I made is from my mind no one tells me you make this or that. this machine is my dream. I will change some part is possible.

[@1crazypj]

@@mr.ranyhomemade2466 To be honest, a heavier lathe is always better as it won't vibrate so much and is more stable. If possible, fill hollow area's with hydraulic cement/concrete (not 'ordinary' Portland cement) as it doesn't shrink and is much much cheaper than epoxy. I trained on much bigger lathes and actually owned a very nice Colchester for a few years but had to sell it when I moved

[@mardyseanofficial9502]

You did the great job, brother. Lovely video.

[@mr.ranyhomemade2466]

Thank you for reaching I do hope you enjoyed my work.

[@graedonmunro1793]

fantastic result!!👍👍sounds peaceful wherever you are..

[@mr.ranyhomemade2466]

Thanks for your best time I will try my hard work to be best. I am Cambodia one of the small country southeast asian.

[@joaoviana3251]

Belo trabalho na construçao de maquina caseira. muito o brigado

[@GhzhsFsghssj-et1ij]

So amazing your creative

[@mr.ranyhomemade2466]

I appreciate for your best time to watch my hard work.

[@bulletproofpepper2]

Thanks for sharing.

[@mr.ranyhomemade2466]

Thank you for your patience 🙏🙏🙏

[@devurandom2019]

Nice Work!

[@ÁREAJ27]

Olá meu amigo, muito bem elaborado, essa ideia ficou fantástica da até vontade de mudar o meu!!!Esse modelo ficou muito pratico, parabéns pela qualidade de trabalho e projeto sempre!!!! Abraço e boa sorte com muita saúde e cada vez mais sucesso!!!

[@mr.ranyhomemade2466]

Olá meu amigo, como vai você? como é o seu trabalho ? bem, vou tentar o meu melhor, sabia que é um trabalho árduo, o problema não é nenhum equipamento, como fazer, posso dizer 60% feito à mão, então tudo parece lento, como um acessório de fresagem, apenas 4 peças, fiz 4 dias. obrigado novamente

[@cokhichetao72]

The master 👍

[@mr.ranyhomemade2466]

Thank you for reaching I do hope enjoy

[@medshop2931]

عمل رائع جدا شكرا جزيلا

[@mr.ranyhomemade2466]

Thanks for your comment

[@sundarAKintelart]

Very nice.

[@MrPov5]

Nice

[@mr.ranyhomemade2466]

Thanks for your watching

[@theoriginalDirtybill]

what's with the coke spoon on your pinky finger?

[@cdrive5757]

I love your work but I hate rusty tools and machines. There's no pleasure watching neglected machines. Please clean up and lube your hard work. They deserve it! Wakodahatchee Chris

[@mr.ranyhomemade2466]

Thanks I appreciated your suggestion I will try my best you knew better than me please let me know Thanks 🙏

[@embitnawai3190]

How much motor bos

[@mr.ranyhomemade2466]

Sorry what did you mean

[@embitnawai3190]

@@mr.ranyhomemade2466 boss, how many watts do you use???

[@mr.ranyhomemade2466]

Sorry I don’t understand what you’re mean 🙂

[@embitnawai3190]

@@mr.ranyhomemade2466 how many watts does the boss use

[@mr.ranyhomemade2466]

Thanks For milling attachment I used 3 pieces

[@Todestelzer]

Can’t understand a thing. Too quiet.

[@mr.ranyhomemade2466]

Thanks suggestions

[@FrankBrown-c5l]

How many times have we got to watch you flapping your hands over a bit of rusty iron as though we've never seen it before ?. Do you really think that we don't know what a piece of iron looks like ?. A thirty minute video which could have been cut down to five. Oooh, can you show us that roundy thing again, I don't think I quite got it the first time ?. And is that an actual rusty bolt I see there ?. Do you buy them ready rusted, or do you have to take the time to rust it yourself ?.

[@mr.ranyhomemade2466]

@@FrankBrown-c5l thanks I thought I seemed crazy cause modern countries use machine making, which by me is handwork because I'm living in the third country that did this. It works and it helps me continue the machine but by hand is not perfect at all. Today I almost finished holding lathe, only one is stuck making the menu south bend carriage I hope can find some of the gears. Thank you for helping me watch.

[@RB-yq7qv]

😃😃😃😃😃😃😃😃😃😃😃😃

[@mr.ranyhomemade2466]

Thank you for reaching I do hope enjoy my homemade

[@Armanufacturingskills]

Nice

[@mr.ranyhomemade2466]

Thank you for reaching