Making My Wheels WIDER! 👄 Relipping

[@literallyanythingelseother]

Adel you think you're slick, but the OGs know you did this like 7 years ago.

[@6spd1uz]

Stephen Bergman on them BBS rims

[@OffBeatGarage]

hehehe

[@astking2869]

Like yuh batty

[@mket_design]

Little tip for finishing the rtv after putting it on the rims, use dishwashsoap and water for a smooth and even finished rtv and the use off tape also.

[@werolopez1997]

This is what we do in the aviation industry when we use rtv/sealant comes out a whole lot better

[@Zombericasian]

Props for that editing of the clicks for the torque wrench, must have been a pain

[@jdmcarboy64]

Why, most wheels only require 42lbs on tq which I think my sister can apply.

[@lifewithmoi5759]

Hondakid64 he’s talking about the editing time

[@realkilju]

@@jdmcarboy64 no, he meant that the editing must have been a pain

[@realkilju]

The editing of the torque wrench clicks was satisfying

[@HKRXPRS]

Steel wool and a bit of soapy water works really well for taking off old sealant.

[@OffBeatGarage]

I'll try that next time!

[@TajBuchanan-vi5iq]

Dose anyone know where i can buy the barrel or three-piece wheels so I can do this conversion

[@staticpedro7843]

What size are your barrels ? Quick question if you take a 5inch barrel and and 5inch lip does that make the wheels 18x10 +0 offset ?????

[@kieranberkery]

Good video, I've some Volk split rims that I need to rebuild so this was interesting. Nice wheels there, I love a bit of dish, but that is an absurd amount! Also, they don't appear to fit the car? I can only assume there will be some sort of widebody or arch extension?

[@jdmcarboy64]

Over fenders coming soon.

[@OffBeatGarage]

Thanks man! The car currently has 50mm overfenders, but they will be bowed out to fit the wheels and tires once the car is on the ground. I'll post about it!

[@kieranberkery]

@@OffBeatGarage Great, I'll look forward to seeing that! 👍

[@freedomprotection3309]

@@OffBeatGarage were did you purchase lips/barrels from?

[@RodeoRanger]

I have American racing Wheels , cast Aluminum U109 's my rears are the widest they come in 9" I need 12" Wide...is there anyway to make them 12" . The design for me is perfect , I just want 12" wide ? Thanks for any advice or help !

[@mikegordillo6743]

Great video cannot wait to start my swap on my meisters L1

[@MRTuning704]

Sandpaper will help you get the sealant off works good for bead seal to

[@stevesanchez1975]

Yo finally someone else knows about croooober

[@finallychurro]

I need one of them hand pointers lmao

[@tomhults5862]

Where can I buy Barrels and Lips?

[@sashasoule4585]

I have a psycho question to ask. Nobody try this at home please but is it possible to shorten the radius of a wheel by shaving the lip? Ie 21 to 20 or 20 to 19 etc? If that’s not a good way, what is a good way to do this but still keep the face of your wheels?

[@AllaboutTheWoodrows]

I like those wheels only thing about multiple pieces wheels I don’t like is the fact the bolts may not come loose but could other than that guess if I had some for me to test I’d probably find no problem

[@cdavis2976]

Hello, how much do you charge to widen wheels

[@mr.cangieter8758]

Awesome stuff yo. Shouldn't you torque in a star pattern? Also I would have ceramic coated the lips prior to assembly. Where I live, stray animals are attracted to pissing on wheels.🤷🏾‍♂️

[@thebeattee569]

i was gonna say, wheels or round objects you always want to torque in a star pattern to avoid any warping or un-even pulling.

[@OffBeatGarage]

We torque in just a 4 across pattern to bring it down. After that go around in a circle. I forgot where I saw it but that's the method for many wheel builders.

[@alwaysgood808]

If you torque from the bolt head your suppose to add 20% so its suppose to be around 20 in lbs

[@rstezza]

Do you have a link to where you bought the new lips from please??

[@SAWVLIGDHAUU]

It’s beautiful. Definitely worth the time.

[@SanggTraashBodyBuilder]

Is that okay if take 2pc wheels faces and make 3pc wheels???

[@josephrugari2145]

was that a mcm barrel bro's hand stick i see there

[@firstnamelastname-th2ju]

i dont know enough about multipiece rims, but shouldnt you have put sealant on the mating surfaces?

[@YourPistachios]

No. That can cause imbalance. You want everything flush and clean and flat.

[@OffBeatGarage]

@@YourPistachios What you said!

[@davidulloa7085]

Did yiu ever sold your old lips

[@boostalmighty5505]

hell ya nice build video heres mine 19x11.5 +12 and 10.5 up front +12 stepped lip

[@patrykkowalski6]

is it possible that power steering pump is causing my car not to self steer as much as it should? or leaks?

[@jessebridges6231]

I can't find anybody that will re-lip my wheels! I'm Georgia, and I don't mind driving to a neighboring state to get it done. Who does it!

[@lewishuysmans7921]

Oof you really need to crisscross when doing the bolts

[@mileofsmiles]

Website super confusing. Don’t actually see where you could buy this?

[@Player45666]

Exactly what I was looking 4

[@battlegeek8118]

To late now but those centers would look mint powder coated white....

[@chastblind7606]

A black lip to. Or black face and white lip

[@jackclark5220]

@@chastblind7606 nope black never looks good. Hides all the detail in wheels.

[@OffBeatGarage]

I think next time around it's going to be purple faces to match the interior and bay!

[@BoostDreamer]

Bought a set of Work Euroline SL and used your last code. Thanks man

[@kemarlyons1999]

How can I order new lip or what the website for that

[@goncalofonseca5935]

May I ask you why the drift enthusiasts tend to choose wheels with straight lips instead of the gorgeous stepped lip???? Just curious if it's an aesthetic decision or if there is any benefit for you particular application....

[@OffBeatGarage]

No specific performance benefit. Mainly it's just because the most popular designs are with wheels that come standard with reverse lips (straight lips) so to go to a step lip you need to rebarrel as well which means twice the cost. Also me personally: the face of a stepped lip wheel is smaller than the face of a reverse lip wheel. So it doesn't look as cool imo because the face doesn't look as big. Also reverse lips tend to look bigger than step lips because they have that continuous reflection. Ex: A 5" reverse lip looks like a larger lip than a 5" step lip, even though they're not. So imo reverse lip wheels look bigger and wider = cooler imo. I hope that answers your question :)

[@goncalofonseca5935]

@@OffBeatGarage Thank you for the reply ☺ It surelly answer my question, but I still prefer the look of a stepped lip 😀😀😀

[@Agent_Q]

technically a step lip setup is more sturdy due to design. But ya i prefer reverse lip cause it looks more pleasing to the eyes cause step lips “look” smaller in the same size due to the 1 step design it (and not to mention having to use a 1” smaller face for a step lip setup like what was mentioned). I mean you can remedy that by rocking FAT nasty 6.5” outer steps on like say a meister (since they come step lipped by factory design) lol cause you’ll DEFINITELY see the width visual there. But overall just go with what look you like the most. The only time step lips would be a functional benefit is when if you are doing some beastly wide as fuck rebuild where your outer lips are like doubled the size of your inners... like say using an 8” outers and 3.5” small ass inners lol. You will PROLLY have a stronger wheel using step lip combo vs goin reverse lip to help with some bent wheel prevention. Ofc people still run reverses in those fat 8” at times just for offset king carshow look cause style pointz for da panty dropping.

[@Agent_Q]

OffBeat Garage and nice choice in 5.5” outers on the rears. I run 4” front n 5.5” rear outers myself on my work equips. Some fatty stuff but not THAT fatty where its too outrageous hahaha. Plus sandwich face designed wheels do make measurements wonky when you rebuild your overall wheels since the faces are 0.5” into your measurements when selecting barrels n lips for your total wheel size.

[@fa74drproductions73]

Teaming up croooober was the best !!!

[@co4988]

Bro can you widen any rim?

[@mattk9438]

holy shit he has a beard now

[@OffBeatGarage]

hehe * blushes *

[@marcusarvie7887]

Could this process be done on a two piece wheel?

[@zacks240sx]

rebuilding my 1980's ssr reverse mesh were a bitch lol, this makes it look easy

[@TazjukieGaming]

I saw a lip with kurb rash tut tut

[@Macedos_Garage]

How about the RB swap? Why didnt post about It anymore?

[@OffBeatGarage]

Need to finish it. Going to buy motor mounts because current ones have terrible fitment. Project has just been on the back burner lately though because of other things going on.

[@TheCrazymanskater]

Where did u buy the lips?

[@mikebanks6704]

Why not use a fine wire wheel to get sealant off

[@ULATAN.]

Where can one source the lips??!

[@TuckedTv]

Looks clean brotha!

[@eriction84]

Where are you ordering your lips from? I have a lot of 20 hole BBS LM, RG-R, RS that I'm splitting and rebuilding.

[@OffBeatGarage]

VRWheels or Wheelflip are solid choices. These were from wheelflip although they had some very very minor flaws and I feel like vrwheels would be better. Wheelflip is cheaper though.

[@peteranthonyanakwe9040]

where do you go for the lips and possibly the hardware?

[@OffBeatGarage]

VRWheels or Wheelflip are solid choices. These were from wheelflip although they had some very very minor flaws and I feel like vrwheels would be better. Wheelflip is cheaper though.

[@CARSHOPBLOOM]

that's gonna look sick!!

[@altezzafriendly7463]

Where did you get the new lips from?

[@OffBeatGarage]

Wheelflip.com although VRwheels also works

[@boran2009ful]

how to get the lip?

[@georgekrapivko]

There is no way you’ll fit that without going even wider overfenders

[@drew-ie9xw]

Where were you able to find the torque specs?

[@OffBeatGarage]

You can call up pretty much any wheel builder and they'll tell you. Or you can look it up via forums etc. Lots of sources :)

[@VERIFIED_COMMENT]

"We're gonna be twerking from the front so we're gonna be twisting nutts"😂

[@NoGoodGarage]

How much is the discount?

[@eriction84]

3%

[@Mia_126ic]

We’re can buy new lip for my wheels?

[@OffBeatGarage]

VRWheels or Wheelflip are solid choices. These were from wheelflip although they had some very very minor flaws and I feel like vrwheels would be better. Wheelflip is cheaper though.

[@mal3762]

What''s the intro and outro song? I wanna rock that bass with my sub

[@OffBeatGarage]

Chase - The Brothers Records

[@gedas3419]

Why yo use so wide rims? (except esthetics) like you'll have hella' stretch which can de-bead the tire, or are you going to drift 295s 305s? Actual I believe you can fit 325s

[@LowCelica82]

Style points. Thats all that matter. Besides im sure with his RB he will able to break 265s

[@alebone_]

Drifting is mostly about style anyways so why not get a couple more style points while you're at it

[@jackclark5220]

Drifting is a rolling car show.

[@OffBeatGarage]

All these responses are on spot ont! Style points! I'll most likely be running a 255 and debeading isn't a problem with that much stretch unless I run below like ~20psi which I don't plan on doing.

[@cantho11]

I love machine lip rims. I can't stand black straight rim with no lip

[@damianzacharko5060]

Good video

[@justinwright54]

Hmm my wide baller wheels arnt wide and baller enough, Installs bigger lips to increase the wideness and baller factor!!!

[@Linkcms2town]

Ayy Simon!

[@Eadss]

Mine next 😍

[@ryangranado8505]

Perfect' Perfect' Perfect'

[@aircoolednation423]

just subscribed because intro to lit

[@aircoolednation423]

wait i remember you, i subscribed before but it didn't save? or unsubscribed? KZbin, fix your stuff.. I watched you shopping on the UpGarage website

[@MRTuning704]

I have a friends who build rims for bro dozers lol

[@klebermartins1721]

Top!

[@LuisAntonio-gz8pe]

Bro I’m looking 18x10 and back 18x12

[@alebone_]

I wish I could split my rays and make em wider ;(

[@stevesanchez1975]

Please if y’all use croooober don’t use them to make a profit, they sell their stuff for cheap for common car guys.

[@lulhoofd2]

hotboi wheels for sure

[@franzein7991]

Where’s a good place to buy lips

[@OffBeatGarage]

VRWheels or Wheelflip are solid choices. These were from wheelflip although they had some very very minor flaws and I feel like vrwheels would be better. Wheelflip is cheaper though.

[@zkmotorhead2943]

where the tdi at👀

[@OffBeatGarage]

For real. I keep wanting to work on it but the s13 is in the garage smh

[@130クラウン]

berry berry nice👍

[@gabrieldiaz5778]

I don’t even care if they take my phone away in class. I’m watching this

[@aeok18109]

How badass of you. OMG. The edgiest edge lord. Let us all bask in your badassery. I wish I could be as cool as this rebel. - _-

[@stanley4290]

Thats some good mindset lmao i like it

[@gabrieldiaz5778]

Ernesto Lugo shut up dilf

[@aeok18109]

@@gabrieldiaz5778 weird ass little attention seeker. Go do your fucking math homework

[@gabrieldiaz5778]

Ernesto Lugo lmao whut? I’m the attention seeker? You’re the one that’s commenting on my shit 😂 Do you feel the need to talk shit to random people on the internet because you’re so mad that mommy and daddy didn’t give you attention? You want attention from people by just talking shit?

[@VIPSTYLEUSA]

Idk if half of inch is even worth redoing your wheels

[@static_chris4097]

I bought some bbs wheels today for $230 😭

[@OffBeatGarage]

Got damn, what a deal!

[@gazcutloose7232]

Lips for days 👌🏼👌🏼👌🏼👌🏼🇬🇧

[@Rob-kw1vz]

Them is chump numbers. Make em wider!!! Jk lol

[@cantho11]

Gotta love them lips

[@Turbski1]

Illiminate ideas

[@lokoako1104]

ricer wheels, lol

[@damianzacharko5060]

Good video