Nice set up and try adding a DC capacitor to smooth out the DC voltage and a longer crank arm to make it easier to turn it.
@awesomemcsumsface14162 жыл бұрын
Correct me if im wrong but isnt this an AC motor so it should be outputing AC current?
@jclowe7352 жыл бұрын
@@awesomemcsumsface1416 your not wrong that is indeed a three phase AC generator/motor which he has connected to a three phase full bridge rectifier to convert the AC output to DC but it's not smooth so adding a DC capacitor to it it'll become a smooth DC voltage which will be better for charging electronic devices such as phones, tablets, laptops or anything that has a battery.
@franc948613 жыл бұрын
Gosto de assistir vídeos desse gênero, eles me inspiram e me trazem Novas ideias. Gostei!
@a_tgamerz3553 жыл бұрын
Bro make this at big Laval👍
@srujantm99403 жыл бұрын
Yes bro please make it
@a_tgamerz3553 жыл бұрын
@Pulak Sinha level
@davidgeiger2 жыл бұрын
Great work, only thought is maybe a flywheel on the generator end to help smooth the minute pulsing hand cranking induces.
@animedj2hd2903 жыл бұрын
thanks bro that's what i was looking for for a school project really thanks for that you get a like.
@yashgautam92232 жыл бұрын
Can you tell me what was your project and how do you made it because my project is 'generator with gear' and I don't know how to complete it
@woodworks21232 жыл бұрын
This is a very nicely made piece. I noticed turning the handle was a little difficult, making the handle longer would help but I think this would be great as a pedal powered device. Not strapping this to a bicycle but like one of they small pedal exercise devices meant to be used while sitting on a chair, I'd love to be able to sit and charge my phone while at my desk or watching TV.
@planktonfun12 жыл бұрын
the 3d print is really good
@shaikirfhanvali17483 жыл бұрын
Bro first 🥇🥇🥇 comment and like brooo🧐🧐🧐🧐
@믿음소망사랑-d6i Жыл бұрын
기계 기술이 대단하십니다
@क्रेजीनंबरवन-न3ष3 жыл бұрын
ले लो पुदीना - आ गया #Pawan Singh का DJ पर तहलका मचाने - Remix Video - Pudina Ae Haseena - Ft. Maahi
@redbull12172 жыл бұрын
Тысячный лайк
@surefiremushroomsmicrogreens3 жыл бұрын
You are the man I swear 😎 I just commented a couple times in your other videos to use a rotor and stator!!!
@jamallaidley47183 жыл бұрын
Very Cool 🤟😎
@0513.R4nDy2 жыл бұрын
well done man
@jomao-astechtv99843 жыл бұрын
Nice,lodz
@codebeat41922 жыл бұрын
Great vid and tut, looks like carefully and well made video with high quality prints and other high quality materials. IMO the handle radius is too close, pushing can made easier by increasing the size of the bar handle. I am also thinking about such kind of generator however by using gravity with a cord and weight, similar way used at an old mechanical clock. This system can be mounted on a wall and can charge a battery or powerbank. To charge the battery you need to manually rewind the weight to the highest position. When released, it starts the charge process. There must be a limit for the weight to fall down like at a mechanical clock so you need special gears for this. This must be not too slow and powerful enough (enough weigth to handle resistance) because when the generator (motor) provides current to the battery, the generator has some 'mechanical' (flux) resistance. It would be great the system can run for a few hours, more than enough to charge the battery to full capacity. This system only needs one preparation for a cycle, gravity (free) and some time to charge it (but this is a normal procedure when charging). What do you think, is this possible?
@rottucow3 жыл бұрын
Do you have the dimensions on PDF for 3D printing, good learning for the coming generations or may I purchase this model for $30US via Paypal.
@garrygill11772 жыл бұрын
Weldon I proud of you
@garrygill11772 жыл бұрын
Nice to project brother
@-ALPHAMAN3 жыл бұрын
It's need more power and torque which is also equal to generator producing power but it's great one keep go bro 👍
@inventorrajesh7833 жыл бұрын
Please make a very powerful DC motor for bicycle
@sssad87572 жыл бұрын
Swing arm is too short. Try to use longer one to rotate easily.
@russell.w14522 жыл бұрын
What’s the music? It sounds nice
@jd876432 жыл бұрын
Tobu - Infectious 😎🤝🏻
@rajatkarmakar45863 жыл бұрын
It feels they purchase the product from market, unassemble it and then make a video of assembling.
@pedromoura15063 жыл бұрын
Top broou
@unjunan3 жыл бұрын
First comment
@invictagaming26833 жыл бұрын
Make it on Big Level
@EmperaGOD2 жыл бұрын
Yo lo haré
@rupamitadebchoudhury42693 жыл бұрын
Please make a V12 engine
@pargalis1622 жыл бұрын
That material is spinning round the coils B?!
@gianfrancopurpura81122 жыл бұрын
occorrerebbe un orologio meccanico per ricaricare quando di vuole una batteria per telefonino.
@Mpomidor3 жыл бұрын
3 volts is good! And how much ampere?
@narendraas54452 жыл бұрын
nice 😘
@lubotin64822 жыл бұрын
Отлично но рукоятку можно сделать и побольше
@user-xxxxxn2 жыл бұрын
change the big and small wheel and it will turn very light
@bosiv41242 жыл бұрын
Hey man, cool project. Just I don't know where the magnet is perpendicular to the coils. Is it in the axel?
@MELLO-jb9en2 жыл бұрын
You can keep it as cycle light too
@موادقيمة3 жыл бұрын
Can you manufacture the engine of the descending weights, you own a plastic sanding machine, and you can manufacture a gearbox from which the motor of the descending weights is made, I will tell you a way to increase the operating period of the motor of the descending weights by multiplying the weights. If the first weight descends, the second weight descends, and the process continues for a period that may reach an hour or hours محمدعلي mohammed ali
@tonypower5625 Жыл бұрын
Where are the the magnets???...it seems they were already installed as part of the spinning drum....👀
@davoodzarei695 Жыл бұрын
🤩🤩❤
@RodrigoSilva-fn6pg3 жыл бұрын
TOP
@coffeenguyenchat58052 жыл бұрын
quay nặng nề quá :)
@brijitrisho92843 жыл бұрын
👍😎
@DCmotorsc.r3 жыл бұрын
Bro key shai hai
@dileepdwivedi51072 жыл бұрын
Give me link to buy these model plz
@ИзраильБагаев3 жыл бұрын
Механизм создан на 3D принтере, но не это важно а суть работы механики.
@catthecommentbothunter68903 жыл бұрын
Blyat
@fabiosantucci66282 жыл бұрын
Try whit a bigger lever
@samuelarthur67882 жыл бұрын
Pliz tell me how u connected the copper wires to the diodes
@CasamTheAnimator Жыл бұрын
This is a replica of 3D Printer Academy's 3 phase generator.
@marcogonlop2 жыл бұрын
me gusta tu diseño, quiero hacer uno pero movido por los pies, con pedales y una rueda de metal muy pesaso tipo giroscopio para conservar la inercia y siga funcionando sin pedalear.
@lackypie16102 жыл бұрын
Я вот не понимаю. Ты напечатал ручку, что бы, когда крутишь, ей не пользоваться? В чем смысл тогда?. Не печатал бы ее. Ну прям бесит
@HuDz1966 Жыл бұрын
Each phase has a coil every 90? I thought each phase only needed 2 coils every 180 :-) ??
@crandonborth Жыл бұрын
It’s 3 phase so yeah every 120°... what the heck is 2 phase at 180° never heard of it?
@pramodjalgaonkar12212 жыл бұрын
Which module gear used
@timson92982 жыл бұрын
Sir can you really design it for me I want to buy it.
@CLOCK-WORK2 жыл бұрын
It's a good thang he copped another youtubers desine
@oneslap012 жыл бұрын
Lol the, light part is scam,it didn't dim lol
@64_bit_coding2 жыл бұрын
Yeah, it also just turned off immediately
@ياسرالربيعي-ب8ك2 жыл бұрын
نفس فكرة ملف الدراجه
@PugsPhotography2 жыл бұрын
Clone tycoon 2.
@inayatullah79892 жыл бұрын
🌹
@inayatullah79892 жыл бұрын
🌹❤
@NINE_YOTA2 жыл бұрын
tenho uma leve desconfiança de ser falso, mas ok
@bangjamil28073 жыл бұрын
Gg
@mahendersingh-ir5yi3 жыл бұрын
Mob no
@microwavetransformer63782 жыл бұрын
Fake : if it was real, the leds whould slowly light up as you gain speed , also it whould have bean way harder to turn if it wasent he was using a battery Also he has a tag free energy which is not real Also he probs bots his subs , comments and likes , there is no way out of 900 000 people on 35 commented or 1 out of 30 000
@graphenepixel82312 жыл бұрын
I noticed, good job at debunking.
@microwavetransformer63782 жыл бұрын
Also i realised a few more things that make this fake The LEDs if they were powered by a real genarator like his whould have a very tiny flicker, i am not sure if you chould see it because very high frequency , 3 phase and the rectifier, but at startup it you should be able to see the small flicker when the frequency is low If it was real the light output whould vary because it is very hard to have consistant crank Also if you are interested in electronics i whould recomend a youtuber called electroBOOM, he is very funny yet educational
@microwavetransformer63782 жыл бұрын
And 1 more thing i forgot is the vidio is very slow to maximise revenue from what i know