Making simply LED Lamp

[@jonathantice9387]

It's videos like this that we will all remember after World War 3 or a huge economic collapse and we will be able to build amazing tech from scrap parts thanks to forward thinkers like M.N. Projects. Thankyou.

[@davesmulders3931]

Seeing that the led strip is probably about 15Watts/1000 lumen, and the led modules are cool white, so around 10W/1000 lumen each, that aluminium profile does not have enough surface to radiate all the heat. It probably runs very hot when you leave it on for half an hour?

[@richardsandwell2285]

A very neat build there, I was told that you also need to put an electrolytic capacitor over the supply in leads, this stops any large in rush currents that could destroy the chips, it basically gives them a soft start. I think I used a 25v 1000uF

[@TheBlackadder-Edmund]

He mentions he is using a 12V supply, which in turn will be DC/Capacitors etc... wouldnt the rush be the same adding a capacitor or not?

[@jameshauser1507]

no

[@johnberry5339]

Wow this is a great tutorial and probably better than something you could buy... :)

[@nilangarukshan8464]

I made a lamp by paralleling two 3.7V 18650 lithium batteries to two 1W LEDs. Can you tell me what the correct resistor is? When the two 3.7V batteries are fully charged, they are around 4.2V, so the LED heats up

[@Vichardhara303]

what is that casing and caping ?? from where to buy this ?

[@maciejnowakprojects]

"Shade for LED tapes" or "led profile" :)

[@taunteratwill1787]

AliExpress has everything you need for all led projects you can think of.

[@iamcytrus]

Have You made power consumption measurements ? With resistors in series You lose min. 14% of total power. Did You consider constant current power supply insterad of constant voltage supply ?

[@kingchiefk.c.7662]

Do you need the resistor?? Should just be able to hook them up in parallel with no resistor if you have a driver right??

[@scott1506]

how can u power 12x 3.6v led chips from a 12v supply?

[@roopavarma4124]

Nice Vedio and the music is simply awesome

[@bratan7498]

Молодец, руки растут откуда надо.

[@zippythechicken]

I would like to do this and power the lights with Solar Panel and AA Batteries do you have any suggestions how I can make them?

[@LearningsExperienceAquarian]

Bro can u tell me wat is triple serial module?? And how much volts needed to run them?

[@Voltermort]

i need help understanding the placement of the resistors, thanks! wicked project.

[@ka6pnl]

How about a parts list and place to buy them. I need to replace a fluorescence desk unit

[@brianvo1437]

Where did you buy the LED case housing? How many volts and Amp for power input?

[@danielwe2517]

May think about glue-thermal-grase instead of mounting with screws - to save parts and time?

[@GoncaloMartins]

I second this, I use thermal paste in the centre and thermal silicone glue on the outer edges. Works a treat.

[@MadeinPolandChannel]

Nice job! :)

[@espenbgh2540]

How much power does each of the two panel comsume?

[@gabrcatt]

if i connect LEDs in parallel mode i also need resistance?

[@Anurag-ky9yt]

which resisters u used in that?

[@convoxccsc7670]

how to connect, how to connect what type of resisters... etc are not showed... what is the voltage adapter that used also not showed

[@egorgozdak9767]

Сколько вольт вы подавали на вход?

[@harishrajamani4922]

hi i have 5w uv led n i need 12 of this leds in series and the each led consume 3.4-3.8 v wit 1400ma can u suggest any driver setup as im using resistor but it get hot wit 12v power supply

[@Wolfgang3418]

Hi! I was making this one, which I can highly recommend. www.christiankoch.de/archiv/led-ksq/

[@natekallu]

Which glue you are using??

[@muniyandimaxi3133]

Where you collect this materials.....?tell us pls

[@antonios4926]

thanks for taking the time and effort to make this video

[@marufulislamnion1049]

its good i like it, if i go to a bulk production how much its gonna cost me ?

[@ezeprojects5425]

What gauge wire did you use to connect the pcb stars?

[@susantpal]

In all electronics presentation the circuit diagram giving value details of all used compnents and stagewise input output is a must. without it, it is just a documentary without purpose.

[@rehanhaque5024]

How many resisters you used for this project???

[@eduardogm8236]

i have those leds and inted to make something like that was been years but i couldnt find those "profiles" as you call. :(

[@Kahvimasteri]

Eduardo GM you know amazon and are eBay are invented

[@eduardogm8236]

international shipping its really expensive sir, dont worth it :)

[@चेतन_महाराष्ट्र]

on eBay some Chinese sellers ship for free internationally. don't ever buy off any chinese website like alibaba.

[@Kahvimasteri]

Tej yea

[@JS-wc4xs]

can u please share the location of where these parts were gathered from?

[@19811402]

they use a lot of power if you connect them like this. You are better of using a 10watt or so led driver.

[@oysterlampable]

What's the name of the group that re made this song?

[@brianvo1437]

Hey! Very nice job. Like it

[@andristefanus]

how many watt overall?

[@N.160.vloger..]

1 watt ko series me karke tub light kaise bnye

[@dm3705]

I love the bgm music, nice work

[@jimmyhornbuckle7449]

Nice video I'm trying to build 8 foot long grow lights for a greenhouse growing Heirloom tomatoes I'm wanting to install them in the trusses of the greenhouse I want to use 4:1 ratio 650nm and 460nm with a few 730nm far par I'm sure what I should use 10 watt leds? I found 75 in long heat sinks on line but not any longer (heat sink USA.com) I would like to wire up 240 volts and daisy chain a few if possible if not then I would run homerun power back the electrical panels but I don't know where to begin and I am trying to get 200 micro moles of light at the plants at 20 inches above the Tomatoe canopy got any suggestions for this project? Leds, power supply

[@lumen5699]

great job but your led caseing where I can buy from??

[@shanthiprakashs7829]

www.ebay.com/sch/i.html?_odkw=led+ceasing&_osacat=0&_from=R40&_trksid=p2045573.m570.l1311.R1.TR12.TRC2.A0.H0.Xled+alum.TRS0&_nkw=led+aluminum+channel&_sacat=0

[@sammy2888]

i am trying to built one under kitchen led light with 3w chips .. intent to use 10 chips .. what is the voltage power supply i need to run this board n chips .. can any one help

[@raymondkgolo8171]

How do I get all that?

[@qazzaq3421]

nice design, simple but effective, what current is required to light-up, i am asumming you used 1A led.

[@wowiealbarracinmcclaskey5392]

Nice video nice build thank you

[@RichDogOfficialMusic]

Can you share the diagram schematic that you used to connect leds?

[@HemantaKrRabha-lv2og]

say about material costs and WHR to find

[@123budujemyPl-blog-budowlany]

cool ! nice job

[@davidshack5574]

I could not get the triple serial module ..! please help me to understand

[@TheBlackadder-Edmund]

These are the "radiators" he mentions at the begining, look on ebay for "star led base aluminium". The "triple serial module" probably makes reference to having 3 points of the star are "negative" and 3 are "positive"

[@Voltermort]

i also dont understand this part, could you please elaborate more for beginners?

[@karimismail3734]

24 LED's Grouped in 3, each 3 connected pos to neg in series as in the video(8 groups)Then each group neg and pos on the ends are connected together ( in parallel) to have each group receive voltage from the source.HELPFUL ?. Good luck.

[@goodgoat3096]

Three LEDs are wired in series, the 12 volt power going to LED #1 anode and the cathode of #1 LED goes to the anode of #2 The cathode of #2 LED goes to the anode of #3 LED and the cathode of #3 LED goes to ground. White LEDs usually have a forward voltage requirement of approximately 3.3 volts and there must be a resistor added anywhere within each string of three LEDs to limit the current, which is normally 350 mA for one watt LEDs. This is repeated 4 times to use 12 LEDs and 4 resistors. The author used a 680 ohm current limiting resistor which should drive the LEDs to full brightness and the power rating should be 2 watts. The 4 LED string anodes all connect to the 12 volts and the 4 LED string cathodes all connect to the ground. Normally there should be at least 4-1/2 square inched of aluminum heat sink area for each watt of LED power being dissipated, so in this design 459 square inches. It would seem like this design could get very hot especially since there is no air flow and the heat is trapped under the plastic diffuser. The power supply should be 12 volts capable of supplying at least 1.5 amps of current, but 2 amps would be better. 12 volts-----\/\/\/- |>----|>----|>----ground

[@НиколайКостов-ю8и]

Hi Good Goat.Please specify this: With 680 ohm resistors each one 1w LED diode consumes 2w energy or one series of 3 LED diodes consumes 2w energy ? Which one is correct ?

[@jacoboisraellarasanchez7133]

how many volts?

[@dermot.jkeogh3497]

COOL!-NICE UNIT,WELL BUILT..COULD YOU SAY WHERE TO GET PARTS YOU USED ,PLS?

[@MrDavid2163]

Friend Thank you for uploading the video How many watts the lamp consumes.

[@bl.randy617]

Awesome!!! Nice make your own LED light =)

[@mhuzaifaamjad2813]

1:11 name of the binging instrument...

[@ramdhansaiidi4746]

Amazing, so bright idea man. Thanks!!

[@charlesurrea1451]

So, I found out something interesting about some commercially sold LED lights. Some use UV emitting LEDs that act on a phosphor coated cover. Works just like a fluorescent bulb without the mercury vapor.

[@Qasem810]

Is there a tutorial how to make RGB lamp using high power leds?

[@Aptenodytes]

So skilled. Wow subbed and faved. I also loved the karambit vid

[@roopehaimila4353]

Why don't you just use two 24V 14,4W/m LED Strips?

[@bor1422]

par purposes. I ll wait another 4 years for the answer.

[@sammy-pp1gl]

Hi thanks for this useful video , I intent to convert my ceiling tube lights to led lights 3 , 5 w light , prefer bright ones .do I need the resisters to fix as what your clips shows . your valuable info please

[@komatsu65]

hi, Great video. I eventually got around to making my own led lighting bar. only thing is, it flickers a bit like a strobe light. Any ideas?I've only used 9nr led instead of twelve. Would this make a difference? it's run of a 12v DC transformer.

[@davidkomdeur]

I'm late, but if you are still wondering it is because the transformer still has AC on the output, so put a full bridge rectifier over the output of the transformer and connect the LEDs to the output of the fbr

Where did you buy the items?

[@jasonjahsah5845]

@ the shop

[@antonios4926]

well done. I am impressed

[@Niaiss]

С прищепкой это ты класс придумал!👍

[@arturhomer2811]

Good job! But on video you compare brightness this two lamp, and you didn't compare power. You use 12 powerLED, and this lamp has 12W electrical power, while second lamp has 2 strip of 60cm, so this lamp has something about 5-6W. Tell us what is a total cost of your product? :)

[@LearningsExperienceAquarian]

Bro make a detailed video like this for 30 cm cube Aquarium and using 1watt leds with 12 v supply bro..

[@Vacation.Trith_vlogs_07]

Bulb name

[@चेतन_महाराष्ट्र]

great video

[@vzvdhd2349]

linh kiện này có bán ở đâu v

Nice build dude. i like it.

[@abyaby9008]

Hello This led bulb which watts.and it's price,?? Plz replay

[@mhuzaifaamjad2813]

Yours the best...

[@davidferguson8478]

You should use a constant current led driver for those types of leds

[@محمدشفیق-غ3ع]

Sir aisa pvc kahan milye ga

[@mhuzaifaamjad2813]

Any one please tell the name of the binding instrument @1 : 11 please....

[@zwillx3953]

clothes pin lol

[@VipsNiceGamePlay]

Very Awesome **o**

[@dibyendukhawas6333]

Kitna volt amp ka led hai koi batayega please???

[@chamilsara]

good work, but be careful when use the drill, use a tool sir,

[@babasolar7100]

bhai material khaha se milega address milega kya

[@КотКросман]

Одноваттные "звёзды" лучше клеить сразу к профилю термоклеем, предварительно отогнув ножки вверх. Таким образом из теплоотвода исключаются подложка и один переход "металл-термопаста-металл", что значительно улучшает отвод тепла.

[@vimalarul3227]

Bro can I get this in skemetik diagram....

[@FloppyCDdrive]

where do you come from???

[@maciejnowakprojects]

From Poland :)

[@FloppyCDdrive]

from germany :)

[@der8lachende8mann]

Hatte mich schon gewundert das er so viel Deutsches Werkzeug benutzt, für einen Ami wäre das ungewöhnlich gewesen ^^

[@dilkashrazat5381]

4 voltage ki battery se 3 watt ka bulb kaise jalaye aaenge

[@gokhanozdemir9314]

Flawless.

[@goodgoat6019]

Have you measured the temperature of the LEDs or the heat sinks? My family is from Iwonicz, two generations ago they came to the US. My grand father was a Corporal in the Russian Army and defected to the US. Two years later my grand mother followed with two children.

[@pyyai4547]

Nice job.. Can you show the connection circuit?

[@vipankumar-vs1wc]

nice job bro but i am not understand soldering

[@muneerramlapresscholakkal7648]

ok this project is very good and yous full but haw can we get the components and profiles to by

[@taunteratwill1787]

MUNEER RAMLA PRESS cholakkal AliExpress China.

[@goodgoat3096]

eBay or Amazon

[@sandeepsharma9434]

Nice series combination

[@manjurani6151]

I can use this led in making drl of scooty

[@martinussugianto1687]

Good job....

[@jeffersonlisboadealmeida2720]

brasilllll.....city..santos.....goood job.....

[@punitvyasbrd]

thank u Shanthi Prakash for sharing link from we can buy

[@fristiansusilo]

Resistor who ohm???

[@SUMITKUMAR-bt2sj]

nice background music....

[@sunilbamiya8091]

Hii

[@jeremydu13]

I'm suprised you don't need an isolating material between bolts and PCB circuit o_O

[@yavuzturan6830]

actually, there is. watch 1:29.

[@jeremydu13]

Yavuz Turan Oh thanks, i didnt pay attention ^^

[@knoellerup_xxshalligalli8627]

Wouldn't it be better to reduce the voltage (diodes, adjustable led-driver) slightly, you would lose a tiny glimpse of brightness, but have less power input, resulting in less warmth and the LEDs could live a longer time?!

[@iceberg789]

the profile you created is giving out blue lights. :D

[@JoshuaPaxton]

cool white, it's got a different color temp.

[@wmtch]

hey man, you said in your karambit video that you would probably do the M9 bayonet, just wanted to know if your still on about this idea ^^

[@maciejnowakprojects]

Of course :) Currently I create a grinder and a hardening furnace. As I wrote in the film description, when I finish the modernization of the workshop I will start doing bayonet! :)

[@wmtch]

nice !

[@naniyanluihttpyoutu.bedbsx6547]

M.N. Projects ，

[@Naveenmahourkoli]

👌👍👏

[@premjameslobo5501]

good one