You should really keep making videos! Finally someone did a vid with the same saw I have! Yeah, now I feel much more confident to make my own zero clearance plate. Thank you!
@abboudworkshop940411 ай бұрын
Thank you! I hope to make more in a couple of months
@Parvindk Жыл бұрын
Thank you for the video, it's great you show the mistakes so we can learn better with you!
@rusticmusicnj37743 жыл бұрын
Fantastic! Not only do I now know how to make my zero clearance throat plate, but I'm also happy to see someone using the same router table I use!
@abboudworkshop94043 жыл бұрын
Glad it was helpful!
@TheBikersurgeon2 жыл бұрын
I love my Kobalt router table too! tossed my Bosch one in the junk pile.
@MYT1FL2 жыл бұрын
@@TheBikersurgeon you must be joking
@adamik622 жыл бұрын
An instructive film. You could still show what a cut with a factory insert looks like and how with the one with zero clearance made by you in the video. Greetings from Poland Adam
@Sly_Wolf_16 ай бұрын
Just an idea to help cut your slot for the blade to through... Cut material almost to size. Stick it to insert with double sided table, replace insert with material attached and raise blade to cut slot. Route edges with guided profile bit, seperate material from factory insert, cut underside notches and now it will fit clearing the blade allowing a full height cut to be raised through it. As for the slit for the RK just use a jigsaw with a straight edge as it doesn't need to be zero clearance.
@bobbyshobbies84222 жыл бұрын
Thanks for sharing. And don’t worry about the “mistakes”, I learned from it too! Appreciate it!!!
@abboudworkshop94042 жыл бұрын
Thank you
@jeffdorrity56093 жыл бұрын
I like your attention to safety (with you camera person’s help)
@abboudworkshop94043 жыл бұрын
Camera people are the best :)
@alvaroandresbarrazaromero5454 Жыл бұрын
Buenas y saludos desde colombia, a este modelo de sierra se le puede colocar el riel deslizante TS?
@abboudworkshop9404 Жыл бұрын
I do not know what is a TS sliding rail.
@shivshah87542 жыл бұрын
Great video . I am new to woodworking . I made this but my keep coming out from the back. Blade is lifting my insert so I am not using it . Can you make one for me ?
@denverrenfro29333 жыл бұрын
I have been wanting to do this for my Delta saw. Congrats on starting a channel!!
@abboudworkshop94043 жыл бұрын
Thanks Denver! Go for it! It was a fun little project and I got to learn about some intricate details about my saw in the process.
@YulRun3 жыл бұрын
Learnt a lot thanks, I have the C10RJ not C10RJ(S) only difference I noticed, is mine does not have that lock for the plate, my plate locks in with a little lever on the plate itself.
@Hansaman589 ай бұрын
Thank you for posting. There is a seller on Etsy making zero clearance inserts for this saw. In Germany so $25 shipping on top of $33 for the insert. Much less expensive to make one.
@PaganWizard3 жыл бұрын
I have this saw, and really appreciate you posting this video. Can you please do a video detailing how you removed the riving knife??? Thanks in advance!!!
@abboudworkshop94043 жыл бұрын
I actually saw it on another youtube video but I don't have the link handy
@troyfromwork9952 жыл бұрын
The only way I saw was to use a Dremel to cut the bottom of the riving knife.
@herbertchung1093 жыл бұрын
You could use your fence to hold insert to make the cut instead of clamps
@abboudworkshop94043 жыл бұрын
That would have been a good idea for me to do :)
@LFichna Жыл бұрын
I will follow your steps except all of the safety mistakes.
@djwill91662 жыл бұрын
great video. Thank you.
@abboudworkshop94042 жыл бұрын
Thank you!
@rubeng.13092 жыл бұрын
Are you happy with the saw? I find lots of reviews of the older model, but nog about this one and i'm seriously in doubt between this one and the dewalt 4792 (similar but a lot more expensive). Best regards
@abboudworkshop94042 жыл бұрын
I have been happy with it. I had it a little over a year now and have used it a lot. Has been a good investment. And for the money, you can't go wrong.
@rubeng.13092 жыл бұрын
@@abboudworkshop9404 thanks for the quick response! If you ever think about making a review with your likes and dislikes, don't hesitate tot inform me 😅 Think you would help out a lot of people in Europe and i would love to share the link ;)
@jasonchuc3 жыл бұрын
When you switched the circular saw blade with the table saw blade, did you have the blade in reverse order?, I noticed the blade brand facing the wrong side and saw dust came out on your side of the table saw.
@abboudworkshop94043 жыл бұрын
You made me look closely... it was in the correct orientation :)
@chuckberry76922 жыл бұрын
Does the saw still roll over to 45^
@abboudworkshop9404 Жыл бұрын
No
@DominikV2353 жыл бұрын
Awesome stuff. Keep it up man
@abboudworkshop94043 жыл бұрын
Thanks! Will do!
@55realitycheck Жыл бұрын
man...where are your safety glasses when using the router??? Spectacles, are not the same thing!!!
@jameslund2212 жыл бұрын
Can you put a dado blade on the saw?
@iabboud2 жыл бұрын
Yes, I used a 6" dado stack in it. I think I could do an 8" too.
@jameslund2212 жыл бұрын
@@iabboud how do I remove the riving knife
@iabboud2 жыл бұрын
@@jameslund221 checkout this video to learn how to remove the rising knife. I used an ocilating saw. kzbin.info/www/bejne/ZmXUhouZrceahas
@brich2929 Жыл бұрын
@@jameslund221 you have to cut the notch in the knife with a saw. Dremel or oscillating tool