Makita DDF456 disassemble. Whats inside gear assembly

This video is for disassembling Makita 18V li ion cordless drill DDF456 (old model BDF456).
I have disassembled it and taken a look at gear assembly. I hope you enjoy!
Be sure to like this video and subscribe for more fresh updates! We try to put out the best content for power tool repair, helping you keep your kit in working order!
~-~~-~~~-~~-~
Check out the below links where you can find new versions of some of these quality brands. That is, of course, if your repairs don't work! As an Amazon Associate I earn from qualifying purchases.
Makita: amzn.to/2IBBDso
Bosch: amzn.to/3o4DmH2
Milwaukee: amzn.to/37iilCI
Dewalt: amzn.to/3nZVaDj
Metabo: amzn.to/31BeEEL
Thanks for visiting! #Handyman

[@garethgedamke7348]

I know how all the pieces fit together thanks to the video, but every time I reassemble it, the gears sit too high and I can't get the plate and cap on and it's driving me absolutely bonkers! What am I doing wrong?

[@felixwilde2551]

i've lost the two pins that block the chuck to insert a drill or a bit (at 11:00), does anyone know the diameter of these (gearbox of a dhp 484) or where one can order them without delivering a whole gearbox;

[@davidprince3856]

Thank you...I missed out the two pins and had to dismantle and re-assemble the whole gearbox on a DHP458 once I saw this. Also important to note that the yoke that goes round the armature only fits one way - there is a notch in the metal that locates to a 'pip' on the plastic case which explains why I couldn't get the damn case halves to close up for hours! Thanks again for your videos.

[@handyman7282]

Thank you, good notice about yoke unit. Now your tool works fine?

[@TheOnlyVibeHQ]

Hi, having this issue now but can’t find the notches anywhere, thanks

[@larsl7841]

Do you know where I can buy spare parts for the gearbox? This would be much appreciated.

[@mpro08]

hi. what is the bearing number? 16:00

[@moffe2k]

Litterally saved me from looooaaads of fault finding on those two small pins! Thank you!

[@joenievesjn]

Thanks for vids like this helped me reassemble the gear clutch on mine 👍

[@kingdomofsalvation]

Thanks, was very helpful, dropped the open gear assembly on the floor, with all the gears and bits flying, got it back together thanks to this video :D

[@handyman7282]

Happy to hear that video helped 🤓

[@mirdallke2]

I am asking you for the dismantling of the makita ddf458, it is necessary to disassemble the gears

[@damiandupart916]

Thanks for your video mate, I service all my makita tools after watching you. Im surprise there is no grease on the gear assembly?!?!

[@KROQER]

Thank you! Your the only one after 20 videos that showed me where those 2 flat pins come from!

[@adelinofernandez9315]

Nice Video, can you tell me pleasy witch nut you use which the ratchet for disassemble?

[@nahpungnome]

10:58 mark...thank you so much. I disassembled my brushless Makita drill in hopes to find an issue. When I tried putting everything back together, I was successful...except those two pins! I had no idea what they were for. I noticed that when I put my drill back together, the chuck would just spin and spin in either direction. After seeing your video and putting the pins back in at a similar place, it worked as expected. My model number is XPH12.

[@comandodeldesierto7516]

Friend a lainita that has that drill where long baes has some dots at one end

[@metallitech]

Impressive knowledge, thanks for sharing. This drill seems like good value now that I see how complex it is.

[@llewellynwilliams1956]

NICE VIDEO IVE REPLACED THE HOLE MOTOR WITH NEW SET OF BUSH SET 21 POUNDS UK ON EBAY

[@gg_noob_pvp]

Добрый день. Может быть у Вас имеется опыт замены плавающего подшипника на оси ударной дрели-шуруповёрта Makita 8270d? Как правильно его снять?

[@sttm1283]

thank you for the video. got a new one at work so i took home the old one and will try to fix it :D

[@iraqisonic9920]

how to repair gear fake makita DF330DWE

[@loochan325]

DF330 is the worst Makita ever, better get a Bosch GSR 12V-15 Heavy Duty @ 2 x 2Ah and 3A charger.

[@romanzbawiciel5221]

1:58 Focus you FACK!

[@MarioMarqui]

obrigado pela esplicação, show de bola

[@PurpleHurrple]

Oh my god I can't believe I only missed the locking bit on the first dis- and reassembly of the gearbox. No wonder it didn't want to stay in place. Thank you so much for pointing each out the pieces roles!

[@handyman7282]

Happy to hear that video helped!

[@xjohnlangerijs527]

ty vm. :D

[@inforbily9928]

Caralho tem peça pra caralho irmão ..

[@davidhumphrey70]

Absolute godsend your disassembly and reassembly videos, I've watched loads and helped massively. Thank you. Do you know if I can get the tiny black pins inside the gear assembly in the UK please? I forgot about them earlier and lost one from inside a DHP482. Thanks in advance

[@handyman7282]

Thank you, I am not sure if you can get them in UK, but I think if you have one you can go to ball bearings shop and they will find something similar

[@davidhumphrey70]

@@handyman7282 awesome. Great idea. Thank you. What a fabulous chap. Hope you're keeping well 👍

[@akramhassan5415]

👍👌👏💐

[@edvaldofranciscodasilvafra3553]

Muito bom gostei 👏👏👍👍

[@RayTeerlink]

Thank you. This was very helpful

[@EpicenterTepla]

👍