MASTER 8 DAYS BIM-BAM ANTIQUE CLOCK | FULL REPAIR | WORKING | RESTORED | RAVI TIMES

[@davidasirvatham8078]

Wow! Super Annan. Unga video'i paathu veli naattukkaaran periyaal aaga pooraan.

[@luckyravi6026]

Thank u

[@sanjeeviponturu8465]

Nice and interesting sir.Thank you.

[@teluguhealthkitchenhacks1932]

one doubt , sir the bell is ringing 2 times when it is one o clock and same for other hours how can we adjust this

[@burakdag7976]

Merhaba ben mekanik saatlerimi dikiş makinesi yağı ile yağlıyorum uygun mu acaba? Ayrıca yılda bir defa yağlamak yeterli mi teşekkürler

[@amiteshnarayanagnihori114]

hi how can connect with you for repair work

[@ganeshrao6746]

Hello sir, I have a Master Clock 8 days BIM-BAM. It's left side spring is brocken 😢, where do it find get this spring ? Plz help me if possible...I am from Bengaluru.

[@mohammadsahabanansari5402]

Ranga se scolding kar do....

[@hassana8658]

Dear when you are cleaning the clock, you should remove the rust on the iron parts also. I have been repairing clocks since 1964 but never did so poor maintenance like you have done.

[@acebusi9140]

Aap ne 2.30 mins k baad jo camere ka angle change Kiya wahi angle ko shuru se set karo .... Thanks

[@vijayjatrate2173]

इस घडी का पार्ट मिलेंगे क्या आपके पास

[@ravindranpmannadiarravindr6532]

How is the Pentilam wall clock speed controlled please reply the what's up group

[@user-br3dn1wd4j]

Sir may I know the location

[@HappyFamily17977]

Spring spare parts enga kidaikum

[@DemiiGodlive]

Where is your shop please adress of ur shop

[@bheeshmachart.k5988]

You did not lubricate,is it ok.

[@ravisankar3899]

Pl share how to do total service of Seiko transistor wall clock

[@shabeebvk1160]

The pendulam stops after some time.direction also correct. What is the reason sir please give me a replay

[@classydays43]

Pendulums usually stop due to one or a number of factors. You can address all of them one by one or all at once if the clock is fully dismantled. When dismantling a clock and cleaning it, you need to make sure all the pivots and bushes that are not worn out are very well polished and free of dirt to reduce friction. I use Autosol on a toothpick for the pivot holes and the same with a cloth and clean out all the residue afterwards but that's probably not the right way to do it. For the ones that are worn, the pivot holes need to be repaired through a process called "bushing". You can find plenty of resources on KZbin to help you out with that. The gears on a lot of clocks have an involute tooth pattern which helps the pinion teeth to push the wheels in rotation; the gears should be running both parallel to the pinions (the little gears) and at the correct distance to avoid binding and worn pivot holes prevent both of these by a LOT. A thinner oil, like sewing machine oil, helps reduce friction as well. Also make sure the pendulum wire swings evenly and is in beat. I found the wire coming from the escape lever on my Sessions clock was bent in all kinds of ways so it needed to be addressed to kep the pendulum running once the movement is level with gravity (use a bubble level to check in all directions). Another factor might be the pinions. If you have lantern pinions (they look like the little gear is made of two brass caps holding a bunch of little wires in place, called "trundles"), they can slip on the Arbor (the axle of the gear assembly) and get all wonky. Straightening them is as easy as using two pairs of pliers to twist them straight again. Now if the wires are worn you might need to replace every one of themwhich is as tedious as it sounds. I've heard piano wire works great for this. Another factor might be the escape levers. Polishing these with a Dremel polishing wheel really helps the levers to actuate on the escape wheel. Oiling the levers doesn't help as the torque on the escapement is so low that any oil on the levers acts more like a glue than a lubricant. And finally, the mainspring might be dirty and dry. A clean spring free of dust and old grease, freshly oiled, works absolute wonders. The spring slips upon itself as it unwinds, so if it binds the power it's meant to deliver is reduced by a bucket load.

[@Jaymaharashtra8490]

Sir apka shop kaha pa he

[@nareshtripathi4761]

नमस्कार जी कृपया बताए कि मास्टर क्लॉक बीम बम का गॉम्ब मे 2 रोड होती है एक टूट गई है उसे कैसे रिपेयर करते हैं क्या आपके पास इसका सेट है आप अपना पता भेज दे धन्यवाद जी

[@Mukeshkumar-el8nx]

Hamare pas hai

[@nareshtripathi4761]

एड्रेस भेजे और कीमत क्या है

[@rudrapandey824]

Sir make a video on how to put a old clock in beat

[@ravisankar3899]

Location please

[@somyakantisengupta9576]

Humko mechanical wall clock ka spare chahiye

[@WaheedKhan-f3u]

Are sir time kaise set krn ye bataiye na....ghante kch baj rhe h aur time kch aur😢

[@mcxruler8056]

Bhai Sahab Mere ghadi 5 minutes pehle he Ghata Baja deti hai ji Koi problem ka solution

[@RizwanAKhan-yu7ve]

घंटा का काँटा फिर से सेट करे

[@sammanimala7543]

E same clock repair ചെയ്‌യുന്ന arelum undel msg pls

[@dattatrayhodgar956]

हेलो सर मुझे पूरा घड़ीमिलेगा

[@somyakantisengupta9576]

It isn't clear

[@walujowalujo4033]

Kok bhs asing..bro. saya buta bhs asing,jadi ya gak ngerti apa itu.

[@vijayjatrate2173]

साहेब आपका कंटात नंबर दो