10 ingenious tricks for every master!

[@ShafaqIftikhar-pw9ld]

Super tricks thank-you for the upload!!!!!

[@glencrandall7051]

Some old, some new, all worthwhile. Thank you for sharing. Have a great day and stay safe.

[@ТлектесДалабаева]

9руб хэхалық

[@lsneiva]

Excelentes truques! 😀

[@andrewbrimmer1797]

Very innovative, very cool

[@FAUZIAKBAR89]

Super kreative 👍🤝 indonesia 🇮🇩🇮🇩🇮🇩

[@masjabrikdiy8422]

hello friends greetings healthy and successful always. thank you for sharing knowledge and always faithfully watching your latest things @💪💪👍👍👍👍👍

[@woodworkingandepoxy643]

Knew most of these. Number 2 has come in handy so many times. Hate buying stuff do I do that instead of buying those stupid little triangles

[@hokaidosax]

#7 is the best one!

[@JT-4real]

To magnetise a screwdriver tightly wrap a coil of wire around the metal shaft and briefly touch both end of the wire on a 12v car battery a couple of times, depending on how stong you want the screwdriver to magnetise. Obvioulsy do it fast so as not to weld the wire to the battery terminals. Mechanics trick in a pinch 👌

[@DireWolfForge]

You can also just slide a refrigerator magnet down the shaft of a screwdriver about ten times to magnetize it.

[@jachconi]

I hang all of my screwdrivers and commonly used bits on a large magnet. That way most of my hardware sticks to them.

[@rezafeghih1541]

سلام دوست عزیز،خیلی نکات کاربردی وزیبایی اموزش می دهید،واقعا شما مخترع بزرگی هستید،ممنون از شما استاد عزیز

[@BAKOV147]

Ещё один великий открыватель Америки через форточку 😂😂😂

[@ВалерийБеликов-щ1н]

The Cool...

[@arkaman4518]

#1!!??

[@fenderstratguy]

#10 Never would have thought of using dental floss for getting glue into a crack. The only ones of these I knew about were #5 and #4. I have done both of those. #2 The spray booth elevators were really clever and cheap.

[@edkinsel3553]

I JUST glued a board when I saw this. 😐Next one...

[@beckyleung7233]

very good

[@makenchips]

I would of left the screws sharp, I use push pins glued to sticks or board. Glue magnet to them an us a steel cookie sheet to UT them where you need them!

[@johnnyalarcon2868]

Gracias..

[@makenchips]

Thank God some one else uses yellow masking tape besides me!!!

[@TIMUR-ASKET]

👍👍👍

[@remshkola]

✌️✌️✌️✌️✌️

[@gisdad1187]

I love the "why didn't I think of that" aspect. Didn't really get #7, but liked everything in general. Good job!

[@cousindave1]

He divided the wood into 2,3 and 4 equal sections without having to do any real maths. Just find a suitable multiple, hold the ruler at an angle where the zero is on one side of the wood and the upper multiple on the other side and then put a mark on each multiple. Example : the wood is 5" wide and you want to divide it in 6 pieces. Place the zero on one edge of the wood and the 6" mark on the other side, then mark off each inch. Of course, units don't matter, so works in inch, feet, cm, metres, etc

[@objection_your_honor]

Love your content. No free (shit) music, is cherry on top.

[@789INFINITI]

💰💪👍

[@masterofcrafts]

🙂🤝👌

[@JdeanJdean]

Put a neodymium magnet on your screwdriver

[@dariuszkardas8924]

Masakra

[@tedinstead9642]

Where is an ingenious trick how not to hit your thumb nail with a hammer?

[@luispaulo362]

Qual a novidade ?

[@lintelle2382]

nuthin new here.

[@woodwizard8911]

после малярной ленты, которой он приклеил саморез к отвертке, поставил диз.. до этого момента досмотрел чтоб поржать))

[@catherineaudran783]

T

[@dredbud9272]

Hacker

[@vasilev888]

Малярный скотч и саморез - это вообще тупость. У тебя, в туалет с туалетной бумагой сходить - это тоже лайфхак?

[@craigmikesell7839]

Huh... just like literally every other video... Unsubscribing

[@Своимируками-и1з]

👍👍👍

[@philippelaperruque6297]

Ces deja vu et revu