DIY Tilting Solar Mount Build!

  Рет қаралды 25,467

Tech4U by James

Tech4U by James

Күн бұрын

Пікірлер: 77
@tiredofeverythingnew
@tiredofeverythingnew Жыл бұрын
Step-by-Step Build Instructions for DIY Tilting Solar Mount: Prepare the Poles: Use 4x6 poles buried 3-4 feet in the ground. Ensure they are all straight and level to the top of each other. Use high-strength concrete to stabilize them. Install Bolts: Once the poles are in place, measure down two inches from the top of the post and put a center mark on that two-inch line. Drill a 1-inch hole, and insert an 8-inch-long 7/8 bolt. Repeat for each pole. Build the Frame: Cut treated 2x6 boards into 9-foot lengths. Use a saw to reverse crown the boards, so the high side is down in the center. Put two washers on the bolt, then slide the board onto the bolts. Add another washer to keep the board from locking to the wood. Repeat the process for the next board. Use blocks cut from 12-foot pieces to lock the boards together. Put two screws on each side and screw them together. Build the Rest of the Frame: Divide the nine-foot boards into three-foot sections, and measure and cut pieces for the inside blocks. Screw these in place to support the 2x6 boards. Mount the Solar Panels: Install hangers to hold the solar panels. Measure the outside edge to the center of the next block to ensure they are all the same length. Screw on the faceboard, then attach the cap board. Test the Mount: The completed mount can hold up to 12 large solar panels and cost around $360 to build. The mount can be easily tilted up and down, and it can be moved around to adjust for seasonal changes. Note: It is recommended to use ground contact pressure-treated lumber for this project. Also, make sure to adjust the mount monthly to ensure maximum power output.
@Scat.original
@Scat.original Жыл бұрын
at what location is the hole drilled in the 2x6?
@swan433
@swan433 Жыл бұрын
2" from the top @ 2:00 min mark he mentions it.@@Scat.original
@JN-qo1ip
@JN-qo1ip Жыл бұрын
Just finished my solar project and want to give a shout out for a great plan and thanks for your kind assistance! Several people including inspectors, utility workers, material suppliers, and trades people have openly admired the ground stand and wanted to know where I got the plan. Of course, I told them I got it from you. Here are few notes and comments. 1. I live on a wind-swept plain in the upper Midwest where the winters are long and cold and soil is sandy, so I used 12" x 48" Ceme-Tube Plastic Standard Concrete Forming Tubes to get below the frost line, minimize frost lock, and provide sufficient ballast. For additional stability, I also added a second row of posts four feet behind the main row (Picture 1). That, combined with 1 ½” vertical gaps and 1” horizontal gaps between the panels meets national code requirements that structures can withstand sustained winds of 106 mph (which, where I live, is expected once every 3,000 years). 😊Since installing, we have had wind gusts in the 40 to 50 mph range, but you would never know it from the panels as they haven't shown even the slightest movement under those conditions. 2. My panels are each 405 kW and measure 40” x 72” mounted horizontally three high in four vertical columns. At that size, I was pushing the span limits of the wood framing and getting slight sag on the outside edges, so I slightly modified the original plan and mounted the four outside fascia boards on the inside with hangers lined up flush with the front of the struts. Then, I went back and added reinforcing boards on the outside (Pictures 2 and 3). 3. Finally, for additional structural integrity, I added 2x6 boards at each corner mounted perpendicularly at 45-degree angles (Pictures 4 and 5). 4. For adjusting the angle, I used 14 Gauge Slotted Steel Angles mounted on each of the posts (Picture 6). They are more than strong enough for the job because the array is nicely balanced and the wind exerts equal pressure on the top and bottom of the array. And, most importantly, the angle irons provide additional support to eliminate any sag or fatigue that might eventually develop in the wood components of the structure.
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Seen the pictures... Awesome work... Love the upgrades. This is how we help others. Very nice job. Glad i could help out.
@tumurmend
@tumurmend 8 ай бұрын
Where can i see the pictures? Thanks
@COGirl444
@COGirl444 Ай бұрын
Maybe you could post the pictures to your channel
@JN-qo1ip
@JN-qo1ip Ай бұрын
@@COGirl444 Thanks. Didn't know I could. Just posted the pics.
@mericasilverpatriot9110
@mericasilverpatriot9110 Жыл бұрын
Best vid on the tube for tilting solar panels
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Thank you.. At least i can share and help someone out!
@earthenergyhex
@earthenergyhex 10 ай бұрын
Saw ya on Facebook, All I can say is what a bunch of A-holes on there.
@larrybell4599
@larrybell4599 Жыл бұрын
I really like your solar frame.
@CptCanuckaNunChucka
@CptCanuckaNunChucka 8 ай бұрын
Excellent design and video! I have some serious wind in North East Ohio by the lake and will be using your design. I'll be adding some overkill. Concrete and posts at a 45 degree angle about 4' behind to help brace it. 40-60mph gusts. Not many trees around. Thanks for sharing!!!
@aspendell209
@aspendell209 Жыл бұрын
Good video James. Here in Alaska it's best to build mounts that can go just past vertical for the solar panels. That way we can catch all the very low sun angles for 6 months out of the year and going 5-10 degrees past vertical greatly reduces snow buildup on the panels, and it also catches all the reflected light from the pristine white snow which can be slightly higher output than pointing the panels directly at the sun. I think the next big thing on solar mounts will be ingenious ideas to help better harvest the full potential of the newer double-sided panels which are able to collect more reflected light than just the front single surface.
@DougMorris-b9k
@DougMorris-b9k Жыл бұрын
Excellent mount. Probably one of the better designs that I have seen for DIY. Thanks for taking the time to make the videos.
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
You bet
@AveRage_Joe
@AveRage_Joe Жыл бұрын
Looks good. I just put my post right into the ground. No concrete!
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Yeah yeah Joe... I am sure that is the way that one is designed lol
@pnowikow
@pnowikow Жыл бұрын
Very nice mount. I'll be curious about the next video
@SooluJuju
@SooluJuju Жыл бұрын
Looked at a lot of these this is pretty impressive Thank You.
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Glad i could help
@keevinboling6691
@keevinboling6691 Жыл бұрын
Use the trailer jack. That way you have a crank handle to tilt your panels
@arnecarlsson9740
@arnecarlsson9740 Жыл бұрын
Very detailed and instructive video, great help for me and others! Well done! 👏👏👏!
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Glad it was helpful!
@jasonbroom7147
@jasonbroom7147 10 ай бұрын
I would consider adding another block of material in-between your pairs of arms that is set to be a positive stop when the array is at it's most vertical orientation. My biggest worry with a system like that is it's TOO easy to move, especially when strong winds turn that entire structure into a giant sail.
@oybeutu
@oybeutu 15 күн бұрын
I'm considering building this exactly but with it not balanced by ~2", slightly off center so the weight pulls it downward toward the winter position.
@huhcom
@huhcom Жыл бұрын
Nice work. I suggest you use bushings in your posts. There should be a way to set up automatic positioning by monitoring panel output and using a linear actuator.
@steventrott8714
@steventrott8714 9 ай бұрын
I would put some 10ga plates at the pivot to spread the load to the post. The uplift from wind loads has me worried about relying on 1” of material to keep it in place.
@IMJUSTBILLUNO
@IMJUSTBILLUNO Жыл бұрын
Nice job. You’ve given me a clue (since I had none) to how I should do my single panel mounted. Thank and I hope you’re better for more videos in the future.
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Glad it helped
@xt1200z1
@xt1200z1 8 ай бұрын
I just ordered 14 panels and researching ground mounts DIY. Found you! I'm in Doyline, Louisiana. Already have a dual axis tracker with 12 panels, probably will put and actuator to tilt with anemometer to know when to go flat for high wind.
@911risky
@911risky 5 ай бұрын
I'm looking into a solar system, I never liked the fixed system. I'm in the tropics and my location is almost in a valley and I was thinking about how to utilizing the sun the entire day as it moves over, I'm glad I saw this idea. Thanks for the video
@Tech4UbyJames
@Tech4UbyJames 5 ай бұрын
Go for it!
@USA-GreedyMenOfNoIntegrity
@USA-GreedyMenOfNoIntegrity Жыл бұрын
Looks good. I need my power in the winter time for heat pump systems. So all mine are fixed tilt from 45 to 66°. I don’t make any adjustments because I have five to ten times the power coming in during the summertime. You need about triple the solar array for the winter time to make it through. Totally off grid. I produced 17 MWh in the last year.
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Nice 👍
@TheRINOShow
@TheRINOShow Жыл бұрын
Very well done. Clear instructions. Thank you! Will be biilding mine this winter.
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Awesome!!!!
@Familyadventure369
@Familyadventure369 Жыл бұрын
Love to add a linear actuator to this
@earthenergyhex
@earthenergyhex Жыл бұрын
nice Step by step explanation
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Thank you
@STxFisherman
@STxFisherman Жыл бұрын
Great video. Thanks for sharing!
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
Thank you!
@Pootntoot
@Pootntoot Жыл бұрын
Great video. Thank you for making it.
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
My pleasure!
@colormaker5070
@colormaker5070 5 ай бұрын
Thank you so much this gave me great information to start my own project
@danstenis660
@danstenis660 Жыл бұрын
If the rack was split into two halves, that would make tilting it manually even lighter.
@PrecisionGroupYT
@PrecisionGroupYT 9 ай бұрын
With the 7/8 bolts did you use a split lock washer between the nut and last washer? Great video thanks!
@olivelebricoleur8461
@olivelebricoleur8461 9 ай бұрын
Bonjour, Les poteaux enterrés, ce sont 14x14 - 16x16 .....ils font qu'elle longueur ? Ils sont bétonnés ? Beau travail 👍 Merci
@DonHighmiller
@DonHighmiller 7 ай бұрын
What is the distance between the 4x6 posts? What is total length and width of array. Great array and video!
@Tech4UbyJames
@Tech4UbyJames 5 ай бұрын
This all depends on your panels.
@timinwisco4921
@timinwisco4921 7 ай бұрын
Did you continue this build in another video? Panel Mounting? ect?
@Tech4UbyJames
@Tech4UbyJames 5 ай бұрын
That is coming... Had work get in the way for a while... Now it's time for me!!!
@timinwisco4921
@timinwisco4921 5 ай бұрын
I can’t wait because after this part, I have no clue what I’m gonna do
@ClanMercer
@ClanMercer 4 ай бұрын
Love the design and I'll be trying something similar. Quick question: what diameter did you dig the holes to? I was thinking of using an 8" auger but a little quick math says that likely wouldn't have enough strength at the corners of the 2x6
@Tech4UbyJames
@Tech4UbyJames 4 ай бұрын
8" auger and widen it out to 10" The biggest i could get for my harbor frieght auger was an 8
@ClanMercer
@ClanMercer 4 ай бұрын
@@Tech4UbyJames Awesome, thanks for the quick reply!
@JN-qo1ip
@JN-qo1ip Жыл бұрын
Thank you, James! Question: just to make sure that I got all the dimensions correct, can you confirm what is the center- to-center measurement between the ground posts?
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
That all depends on the size of your panels. On the one in the video it was 9’6”
@JN-qo1ip
@JN-qo1ip Жыл бұрын
@@Tech4UbyJames Thanks. Just emailed you at your Gmail address.
@abovethelevelentertainment430
@abovethelevelentertainment430 5 ай бұрын
but where do you buy the bolts?
@Tech4UbyJames
@Tech4UbyJames 5 ай бұрын
Tractor Supply
@coachtimp
@coachtimp 7 ай бұрын
Are the first 2x6 you put on did you center the hole on it, when you drilled it? or is it offset? thanks great video
@raygibson1295
@raygibson1295 Жыл бұрын
How did you know how long to make the topp and bottom?
@dimitrisklonaris6733
@dimitrisklonaris6733 8 ай бұрын
You are good!
@brandonoh777
@brandonoh777 Жыл бұрын
Have you ever considered a manual jack screw ( manual linear actuator) type of setup for you're tilting mechanism? I'm planning on building a similar adjustable wood ground mount and that is what I plan on using on all the posts.... quick question so you're using 4 x 6 posts... what diameter were your holes in the ground?
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
I have a video coming with a winch installed for tilting the array. The holes are 9"
@brandonoh777
@brandonoh777 Жыл бұрын
@@Tech4UbyJames I think you said you used a power auger from Harbor Freight?
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
@@brandonoh777 Yes it was an 8" and we reamed it out to 9" But now i have a new toy... Video coming soon.
@mikerumer501
@mikerumer501 Жыл бұрын
what is the distance between posts in ground?
@Tech4UbyJames
@Tech4UbyJames Жыл бұрын
That depends on your panels. Mine is at 10'6"
@Jachan-lu8yf
@Jachan-lu8yf 7 ай бұрын
Did you devise a way to tie the tilt assembly to the posts to enable monthly adjustment?
@Tech4UbyJames
@Tech4UbyJames 5 ай бұрын
Not yet. Just using 1x4's at the moment
@raygibson1295
@raygibson1295 Жыл бұрын
How much did you cut off the 4x6?
@JamesHodgson-v5w
@JamesHodgson-v5w 9 ай бұрын
What are your facial boards length.
@chrisnordstrom7431
@chrisnordstrom7431 10 ай бұрын
Material links?
@MrSteeDoo
@MrSteeDoo 7 ай бұрын
tuba six!
@timinwisco4921
@timinwisco4921 7 ай бұрын
@swan433 I think you misunderstand @Scat.original They are referring to the first 2 - 2x6's he put up, not the 4x6's
DIY Adjustable Solar Panel Ground Mount - Part 1
17:59
Rodney Hunt
Рет қаралды 23 М.
How to Build the Ultimate DIY Solar Panel Ground Mount
15:15
Martin Johnson - Off Grid Living
Рет қаралды 254 М.
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН
coco在求救? #小丑 #天使 #shorts
00:29
好人小丑
Рет қаралды 120 МЛН
UFC 310 : Рахмонов VS Мачадо Гэрри
05:00
Setanta Sports UFC
Рет қаралды 1,2 МЛН
Tilting solar mount price breakdown and upcoming things
13:26
Tech4U by James
Рет қаралды 10 М.
Our Own Power? They said we couldnt do it   ❤️#lifeonthehomestead #solar
18:21
Hippy-Cow-Yay Homestead
Рет қаралды 13 М.
10 Solar Panels on a 4 Panel Rack HAHAHAHAAAA!!!!!
11:03
AveRage Joe
Рет қаралды 44 М.
A Shocking Discovery - Grounding Your Solar Panel Frames
22:46
Adam De Lay
Рет қаралды 78 М.
Fence Contractors Hate Me For Showing You This!
24:50
HAXMAN
Рет қаралды 4,5 МЛН
Ground Mounts: Why We Choose Sinclair
12:12
Engineer775
Рет қаралды 74 М.
How to Wire Different Sizes of Camper Solar Panels Together - Effects of Mismatched Solar Panels
12:19
EXPLORIST life Mobile Marine & Off-Grid Electrical
Рет қаралды 376 М.
Quando A Diferença De Altura É Muito Grande 😲😂
00:12
Mari Maria
Рет қаралды 45 МЛН