Max 6x6 T20 Transmission Band Adjustment

[@joehrs]

excellent info. keep up the good work. here are some topics of interest... 1. how to troubleshoot popping chains and strange noises 2. wheel bearing install 3. removal of max iv tub 4. how to properly adjust chains 5. engine removal on max iv

[@dickykitchen7169]

Just want you to know how much your venison are appreciated !!!!!!!!!!!!!!!! Thanks a Million :)

[@darcyfunk]

Thanks! Planning to replace the transmission in my 1984 Argo 8 x 8 with a T 20.

[@ianread1486]

A very helpful and informative video, you're a legend.

[@raymathieu3052]

Case anyone needs them (3804-2RS Angular Contact Bearing Sealed 20x32x10) , these are for the T-20 trans outer bearings , they can be bought at VXB Bearings . This is the correct bearing for this job . Just make sure the bearing says angular contact , this makes sure you are getting double row bearing .

[@scottiecharlton]

I needed this. Thank you!

[@shanehinton1777]

What does it mean when the band plunger pulls almost all the way out of the housing unit?

[@alexburns6584]

Shane Hinton Did you happen to figure this issue out? My max IV is doing the same thing on the right side.

[@Rodrigues680]

It means that your band needs new lining the new ones comes at 0.120 if I'm not mistaking

[@kaleba5443]

What does it mean if one of my transmission lever to engage forward and reverse will not move past neutral? Does everything for reverse just fine and neutral but only one side engages for forward.

[@jcmate1692]

is the T20 skid steer or can you have one track going forward while the other track goes back or does it just lock one track to turn. and what sort of hp can they handle would really like to know cheers jace

[@RustyGunn7]

Is there a reason you didn't use the band adjustment tools and an inch-pound wrench?

[@MaximumOffRoad]

20 years of adjusting and tightening :)

[@kirbymills5973]

@@MaximumOffRoad I like your way, I love the max 4 kabota you sold me, great video!

[@dwayneg.8717]

My max 2 wants to pull to the right a bit...have to counter steer to keep it straight. Tires have same air pressure the whole way around. Any suggestions?

[@zolinagy9366]

I have a same problem

[@alcopower5710]

Thanks for the video......very informative

[@smilergrogan3344]

Awsome videos dude very helpful !!!! thanks

[@MaximumOffRoad]

Glad to help!

[@letsbelogical5537]

Brandon, thanks for this vid! can you suggest anyone that rebuilds these transmissions? I am in Texas...just got a 1994 Max II...but the trans is shot. thanks for any help!

[@MaximumOffRoad]

Not many rebuilders left anymore. I'm sure Richard's Relics can do it or Midwest ATV might still rebuild them.

[@letsbelogical5537]

+MaxRules99 . Great! thanks for taking the time to reply and post the vids. these are a great help sir!

[@wildone5295]

Great video!! Thanks

[@chrischwaz7788]

I just got a max2 with the roll bar on it how do I open it up the roll bar is going threw the upper body and to the frame ?

[@MaximumOffRoad]

The rollbar just sits on the frame and connects with two pins that are under the seat. It really doesn’t change how you open up the body. Just remove all wing nuts around the edge except for the front three.

[@morganismyname9998]

Hey, great vid keep it up!

[@jasonglonestar]

My 8x8 tracks left slightly and am constantly having to brake the right side to stay straight.. what is the solution?

[@MaximumOffRoad]

That is usually caused by tire air pressure being higher on one side, causing those tires to be a larger diameter.

[@MISP888]

Thank you so much!!!

[@mudlifejunkiepr3937]

how much do you charge to rebuild a t 20

[@MaximumOffRoad]

We no longer do any ATV service, but the cost the last time we did it was $145 Labor, plus parts.

[@jimmiedixon5153]

can you do this adjustment while transmission is still install in MAX.

[@MaximumOffRoad]

Sure, just remove the large springs holding the steering levers forward.

[@jimmiedixon5153]

@@MaximumOffRoad Thanks for the help.

[@roofking2314]

Do you still rebuild

[@MaximumOffRoad]

No sorry, that business is long gone.

[@chadguidry6262]

Any chance you'd be interested in doing a rebuild?

[@MaximumOffRoad]

No sorry I've been out a long time, I don't know who to recommend anymore.

[@Niterider73]

You guys still work on these 6x6s? You guys ain't too far from me and I would like to get some work done on my 78 Max ii

[@MaximumOffRoad]

No I’ve been out of it for a while. Check Richard‘s Relics in Indiana.

[@edwardandrews3860]

Do you rebuild for public what is price

[@jacobw446]

They need to make a t20 transmission with external disc brakes, for the diy'er.

[@MaximumOffRoad]

Many old T20s from models like the Attex did have large disc brakes attached to the sprockets.