Maytag dryer - change belt & rollers, how to remove front

[@jz53223]

My Maytag dryer is exactly the same as the one in the video. All the same controls and printing on the control panel. Maytag Dependable Care, Quiet Pack, Heavy Duty. It is model LDG4916AAE and serial # 10736647QY. Manufactured in Nov 1996, Newton Iowa USA. Btw, I did all this work on mine by myself. I would've been happy to have someone with big, hairy arms to help me!

[@michellesfrugallivin]

good info thanks. Yes having a hairy armed man's help is nice.

[@michellesfrugallivin]

@@Lord_Zore I don't have that dryer any more. It seems to me that if it is working for you then don't change anything.

[@fredoh2010]

Exactly what I needed! This was the BEST Maytag repair video of them all. Showed every step. Thank you SO MUCH!!!

[@michellesfrugallivin]

Thanks for watching

[@Buckethead1074]

I just did this repair this morning. A little hack to make it much easier and save some wear on your knees. Unbolt the wheel shaft and pull the whole assembly out. Its easier than reaching back there to take the snap ring off. The replacement kit comes with new shafts so assemble them first then all you have to do is bolt it back up.

[@michellesfrugallivin]

Nice

[@ronahue1946]

This was a big help to me. One thing I did differently because I have an awful snap ring plier is I put them on before placement of the wheel... this was real easy on the left side and not too bad on the right but on that side there is only room for a wrench behind the wheel but I had new wheels so the nut could be hand tightened mostly. Thanks for making the video.

[@TheShoreman1]

Thanks. Very helpful. The belt on my Maytag #LDE9306ACE had slipped into a groove on the drum and was thus, not in the right place. This caused the belt to appear to be too long and rub against itself at the motor pulley. Just needed to see how the belt was routed. Exactly what I needed to see. Thanks again.

[@paulah.8294]

Thank you so much!!! I just replaced the wheel part on mine and couldn't get it back together because someone else took the front off. You are amazing thank you for the clear easy to see and follow video!!!!

[@michellesfrugallivin]

I am glad the video helped!

[@ronahue1946]

Thanks for the video... big help. I would like to add a tip on the belt... It wants to curl back to the way it is packaged making it hard to get it twisted correctly (smooth side around the drum) as it curls and I found getting it in position on the motor and slack adjuster difficult. I used 4 magnets in the end but later thought if I had hung it with a heavy weight overnight in the correct configuration it might have made a difference.

[@michellesfrugallivin]

That is a good idea. Probably could be applied to anything that is coiled up like that. It seems like I am always buying parts just before I install them...like the belt for the lawn mower deck. Always has a tight bend in it.

[@jackstraw5527]

Ever had an issue where the dryer spins very slow? I was told it was a belt. Thanks for this video!

[@michellesfrugallivin]

That does seem like a worn out belt. It would be worth opening it up and checking it for cracks or if it is loose.

[@jackstraw5527]

@@michellesfrugallivin I opened it up and replaced it. Thanks! It was so much easier than I thought it would be.

[@michellesfrugallivin]

@@jackstraw5527 good

[@bobholst874]

If your rollers were binding up, it is a good idea to replace the shafts along with the new rollers. There is a 9/16 nut and lockwasher on the back side of the mounting plate. I have found it wise to use only OEM Rollers. I had to replace 2 aftermarket rollers at different times. Better to do repair 1 time in lifetime than multiples!

[@michellesfrugallivin]

good idea

[@JohnB5304]

I just replaced the Blower Wheel with Clamp, Heating Element - 240V and the Drum Support \Roller Shaft Kit i shopped around to find parts before ordering and can find deals. This was an easy fix after watching this vid, good job Y'all.

[@michellesfrugallivin]

thanks for watching. On a side note, it turned out that the plastic fan blades in the blower was causing the noise. The hole where it went onto the metal rod that is connected to the motor used to have a flat area that matched a flat area on the rod. It was all worn out and the rod had made the hole completely round. It was just flopping around on the rod.

[@xoringe]

My Maytag MDE5500AYW developed a loud squealing due to a dragging right-hand drum support roller just like yours. I replaced both rollers while I was in there and now it runs like new, BUT… The old roller failed because 19 years of supporting a slightly angled drum shifted the roller rearward ~3mm on its bearing until it eventually rubbed on the white metal housing behind it. So if you clean your spindle and it looks fine, check to see if the metal bearing is still centered in the support roller. If not, press it back in or just FLIP IT AROUND for 19 more years, free!

[@michellesfrugallivin]

Good advice

[@ScottDuensing]

Thank you! Just fixed my dryer with this video!

[@michellesfrugallivin]

great

[@jzxwood]

Thanks for the very detailed video! I have a maytag dryer too, my belt broke last week!

[@michellesfrugallivin]

Glad it was helpful!

[@ProjectCryo]

Only one that worked for me been out of a dryer for 2 weeks and just seeing the back helped so much

[@routinedrop4692]

You and your husband are awesome! I wish I could fix things with my wife and have her understand anything. Great video!

[@michellesfrugallivin]

We fix lots of stuff together. I always was always watching and helping dad when I was young and I watched all the PBS fix it show growing up. Thanks for watching.

[@lauren-8889]

I wish I could fix things with my husband and have HIM understand anything!

[@lonnieblackwell5107]

Excellent video. Just what I needed for a Maytag dryer left in a house I just bought. Works except it “clunks and screeches” when rotating.

[@johnevon8220]

Video was very good learned a lot thank you. would have been nice to hear the squeaky noise in action before tear down, people would say, yup that's the sound mine makes

[@ju2067]

Thank you so much. Have the exact same dryer and so easy to fix. No computer to go wrong like newer appliances and these thing work really well.

[@michellesfrugallivin]

Glad it helped. I now have the newer computer ones. I hate to think about them breaking.

[@sthrn1378]

Ju what size belt does this take I have same unit

[@michellesfrugallivin]

I don't know. I don't have it any more.

[@journeyappliance7807]

your camera person is a really good helper I could use her in my business lol great video

[@michellesfrugallivin]

Thank you. I do try to be helpful when he is fixing things.

[@danschechter9069]

Great video -- well done! You probably already know this, but the special pliers are called snap ring pliers. You can get them at most auto parts stores for about $6. Don't try this repair job without them. And don't ask how I know this, please. (Sigh.)

[@michellesfrugallivin]

those pliers to help😁

[@tm4000m]

Just saved me a service call! THANKS!!

[@BayouCityzen]

Thank you, thank you, THANK YOU!!! I have a model LDE9806ACE and your video is the only one that I found with instructions that almost exactly corresponded to this model. The only difference is one additional wire attaching to connector on the front panel along with the yellow and white wires. Also, using the rear access panel to get to the pulley assembly is brilliant! So much easier than all the other videos I found showing people reaching around and working by feel back there. I've got it apart now and diagnosed to a bad drum roller. I'll probably replace the belt while I'm at it, given the dryer is 26 years old now .😃 I have a question for you: When I removed the front panel, there were two pieces of foam, about an inch thick, that just kind of fell out. It looks like they were attached to the door. They have deteriorated to the point where I wouldn't attempt to put them back. I haven't seen any mention of something like this anywhere. Did your dryer have similar foam pieces inside the front panel?

[@michellesfrugallivin]

I am glad you found my video. We made these dryer videos because we couldn't find any for us to watch so I figured people would find them useful. I don't know about the foam pieces. It does seem odd they would be in there. Doesn't seem like you would want foam in something that heats up. After you get to using it again, keep an eye on it to see if you think they were actually doing anything for you.

[@ShorelineHomeschool]

Great job! Its so awesome that you can fix your home products. I often have to, as well.

[@brianash5096]

Michelle, thank you so much for the video. I have the same dryer - your video was extremely helpful, especially since the belt tensioner is different than many of the other videos I've seen. My model sticker is worn off. If you could be so kind as to look at the sticker inside the door, below the opening of the dryer, and give the model number, it would be very helpful to people. It will also help people find this video if they search by model. Thanks again! I really would have struggled getting the belt on if not for your vid!

[@michellesfrugallivin]

Glad it could help you. It isn't my dryer but I should see it this weekend and see if it has the model number.

[@7lines]

My dryer looks exactly like that one and is model # LDE9306ACE & serial # 10647948SK. Hope that helps others.

[@michellesfrugallivin]

thank you

[@calgaryscluelessdrivers1794]

Great video

[@tej226]

Thank you thank you! Same make and model as mine, same noises and all. With some help, I hope to fix it

[@Kovaction]

Awesome sauce. Thanks for this. lde9606ace rumbling and I have to replace the rollers and belt... but probably the washers too. Nice to save the dryer from the landfill before it's time.

[@Kovaction]

So it was mostly a success. Quieter but I'm wondering about the tensioner... May still be a source of some rumble... But much better. Thanks again!

[@1165slugman]

The older ones that are electromechanical no computer and humidity sensor are more reliable and dry better

[@stevemccooleq]

And are much easier to fix if something does break.

[@daviddoan8076]

Thank you!

[@ponketon]

Thanks for the video, it help me out alot.

[@jduub10]

Nice job guys

[@amadoresparza772]

How to replace de thermostat in same Dryer?

[@ariselgreenhill2690]

Awesome video! I’m a bit confused with the direction of the belt. I’ve replaced many belts in the past however this model is a bit different. A first for me. The pulley is quite big and the direction in which it goes in your video would put the grooves facing outside instead of against the drum. (In order for the grooves to sit on the shaft) am I correct or confused lol heeellllllllppppppppp 😊

[@michellesfrugallivin]

someone else commented that too. It has been long enough that I don't remember. You should really go with what you think works especially since you have done them before. I don't remember there being any problem after we put it all back together. And not too long after we replaced this belt he was given a new washer and dryer so we don't have it any more.

[@jz53223]

The belt goes on, smooth side against drum. A little counter-intuitive, but that's how it goes on. As you said, so that the grooved side rides on the motor shaft.

[@speedfreak8200]

Ha,O-ring pliers, gotta love the ladie's terminology ... snap ring

[@lauren-8889]

Condescending

[@1165slugman]

Actually it's called a split ring not a snap ring. And the tool is split ring pliers.

[@enavy58]

Thank you for pointing out the difference in terminology. Whether you want to call it a split ring or a snap ring? The important thing is to understand that it’s a metal retaining ring, that holds the roller in place, on the shaft. NOT an “O” ring, which is usually rubber and that usually keeps fluids in a cylinder. This is an excellent video of superior quality and lighting, so you can see how things work and are assembled. Thank you Michelle and your man too! Awesome work!

[@albertosilva2878]

What band measurement is 92 1/2 long

[@kramco.5984]

The grooved side of the belt goes inside against the drum, no? Is your belt a tad loose?

[@liggc]

Hello, I have seen several videos in which they place the band in this way

[@ad2181]

Not sure what is right way (flat on drum cause grooves on motor pulley) or ( grooves on drum causes flat on motor pully) Seen another video that contradicts.

[@woodsey52]

need to see how to get the clips back in...why didn't you show that or was it too hard to do?

[@michellesfrugallivin]

It probably wasn't difficult and he probably put it back on there before I noticed.

[@homevideos91]

Any idea where the hi limit thermostat is on model Maytag gas dryer model PYG2300AWW? Thanks!

[@brandobz3dtv602]

Do you know why that dryer model would sound like there is a brick 🧱 in the dryer when it’s drying?

[@michellesfrugallivin]

I had a dryer that had a noise like that. When I opened it I saw that the drum was rubbing on the top. Over the years of me sitting stuff on top of the dryer it had bowed down and was rubbing the drum. Made an horrible sound.

[@googleuser7853]

I have this same dryer electric . Model# LDE8426ACM Since it is an older model where did you get the replacement belt? Mine broke but putting the tape measure against it shows 991/4" but I can't find that the longest I've found it 93

[@michellesfrugallivin]

There happens to be this very old mom and pop kind of store here that does nothing but appliance parts. It is called the handy man and is in jeffersonville Indiana

[@ren7ee]

I have this model and it stopped turning on completely. I'm thinking maybe it needs a new fuse but I don't know where the fuse is located. Is it in this video?

[@michellesfrugallivin]

I didn't talk about fuses in this video. There aren't a lot of places they can be. Either flip the top open or take the back off and look at all the wire connections.

[@ren7ee]

@@michellesfrugallivin My dryer is the exact same model as the one in the video. There's only a small square panel on the back on the bottom right corner. Maybe it's there. There's no way to remove the entire back panel from what I can see.

[@michellesfrugallivin]

@@ren7ee ok I had to look at the video again to see which dryer it is. I was getting it confused with another one we worked on. This dryer was very old and maybe yours is too. I am not sure it has any fuses and I don't think we ever opened the top. you could have a switch burned out on one of the control knobs or the door closed button.

[@ren7ee]

@@michellesfrugallivin For what it would cost to have someone come out to repair it, I maybe should just buy a used one.

[@michellesfrugallivin]

@@ren7ee right. My man was given a used newer set a while back so he doesn't have this one in the video any more.

[@sthrn1378]

Plse what is the belt size I have same dryer and I got wrong belt but don't know correct size

[@kedoriwilson]

Hi. Can you tell me how to use this dryer. I have been drying my clothes all evening and its the 3rd time I have had to restart it. My clothes just aren't dry.

[@michellesfrugallivin]

you might need to clean out your vent pipe. The lint collects in there and really decreases the drying. This might mean disconnecting it from the back of the dryer for access in the house and go outside and clean out the opening on your house. You can buy a brush on a flexible handle to run through it to really clean it out.

[@rapaent]

What happened to the end of your video???? Would be nice to see if it ran ok..........

[@michellesfrugallivin]

Sorry if it seems like no real ending. Sometimes, when I do videos with my man, things get a little difficult. The dryer runs just fine. He was given a newer model, so this one is in storage until someone needs it.

[@azrooster602]

love it

[@peppon_9724]

What is the belt that you used can’t see to find it

[@michellesfrugallivin]

I can't remember exactly what the belt was. We buy parts from a local parts store. You might see if this is your model # LDE9306ACE & serial # 10647948SK. there is a website appliancepartspros .com

[@heidib7026]

I have that exact same dryer and flooring 🤣🤣

[@michellesfrugallivin]

LOL Did you think we were in your laundry room.

[@jackeemoore1545]

My washer don’t wash correctly

[@brandilocs4657]

I sure hope this shows me how to put the door back on. I did the hardest part: taking it apart to unloosen and remove a strap from a mechanism now I can't fit the door on the grooves...ugh!

[@DreamlandWildlife]

Do you have any videos that explain how to fix this same dryer not heating?

[@michellesfrugallivin]

No. This dryer is gas. It could be the switch if you have gas. If you have electric it could be a sensor that is connected to the coils or the coils or the switch on the door or the on off switch. If you have a handyman shop that sells appliance parts they can test you sensor or switch to see if they are bad. I did a video on a whirlpool dryer electric that had no heat. You can find that video in my appliance repair playlist linked my homepage.

[@Jerry-Parker]

Thank you so much ! 👍 Excellent Video ! 5 ⭐👍

[@rafaelpalacios9720]

Hi , i need some hlp .. Which one model is? .. Belt ? .. 90 in. 100 in? .. thanks you

[@michellesfrugallivin]

I don't know

[@brianash5096]

I would love to know the model too, my sticker is worn off. I have the same model dryer - the belt is 312959, which is 100 inches.

[@michellesfrugallivin]

@@brianash5096 Ford W 13 hours ago My dryer looks exactly like that one and is model # LDE9306ACE & serial # 10647948SK. Hope that helps others.

[@ad2181]

The flat side goes against the drum, so the grooves side matches the motor pulley grooves and the flat side against the idler wheel.

[@raymondallen7870]

Great video the first one I picked same model as mine

[@phatbackbeat6553]

Mine looks just like this. Model # MDE508dayw

[@melvinmcisaac6215]

Could be pully wheel squeeking

[@mattiasfenton2847]

What do you mean ‘two screws at the bottom?’ At the bottom of what?? At the first step a pretty big fail. Not specific with words. Not showing where the screws are with the camera. Don’t quit your day job.

[@AdvancedTacticalHSV]

Thank you, this is a really good video.