Warning! I forgot to mention in the video but DO NOT change the speed on the override or in the program during or after the machine has cut the part on these older controls. The machine will loose the thread lead if you alter the speed and it WILL scrap your part. BTDT. Only make changes to the spindle speed after you get the part off the machine.
@derick34823 жыл бұрын
you should've shown how to do a spring pass cause that's what you need right?? just clean it up
@mazatroltipsandtricks68163 жыл бұрын
@@derick3482 I didn't think about it at the time, but yeah easy to do on Mazatrol.
@saravananj3843 жыл бұрын
Thanks sir
@mazatroltipsandtricks68163 жыл бұрын
@@christophercolumbus8944 The way Mazatrol works is you need to have a minimum of 3 passes in the threading line.
@bobbymarkiewicz49332 жыл бұрын
Thanks for your time. You save me time by not digging though 20 year old manuals! Thanks again.
@mazatroltipsandtricks68162 жыл бұрын
You're welcome.
@ronaldmadican23934 жыл бұрын
This is the first youtube channel I have subscribed to. I am just blown away with how well you explain everything. We have a T2 Mazak so your videos will help train our newbies. Thankyou very much.
@mazatroltipsandtricks68164 жыл бұрын
Thanks for the positive feedback!
@christophercolumbus8944 Жыл бұрын
what control do you have? do you use EIA a lot?
@thomasmedlin28812 жыл бұрын
Phil, I am just starting with Mazatrol Programming and I am learning a lot from you. Thanks
@mazatroltipsandtricks68162 жыл бұрын
Glad to hear its helpful.
@russguppy87613 жыл бұрын
Excellent video. I like that you got closer to the Nazak screen so I can see better. Thanks
@alejandrodavilacortes57722 жыл бұрын
Thank you sir. I found this very helpful 👍
@mazatroltipsandtricks68162 жыл бұрын
Glad to hear it.
@billmcmahon96973 жыл бұрын
Thanks for the quality video, you cleared up some finer points for me.
@mazatroltipsandtricks68163 жыл бұрын
Cool. Thanks for the compliment.
@harrychristensen59923 жыл бұрын
Tip: At 10:35 where you can set the next line to thread i an taper, If you rewrite the same stop point again eg: FPT-X =3 FPT-Z=1.8 the machine transit in a smoother motion at the end of the thread and not doing the sudden stop motion. Works on newer machines don't know about this machine.
@mazatroltipsandtricks68163 жыл бұрын
I will have to try that. Thanks.
@АндрейСугойдь-у5у3 жыл бұрын
Дажэ хлопцы у Беларуси глядяць, дрэнна язык разумею, Але Фил маладец, пахожэ што шарыць
@Docaga19784 жыл бұрын
Phil, can you do rethreading, if need to rework the workpiece that already took out of the chuck?
@stanleyfei80452 жыл бұрын
Thank you teacher
@mazatroltipsandtricks68162 жыл бұрын
You're welcome.
@mansoorahmed33375 ай бұрын
Thanks for the awesome videos. I am trying to make internal threading toolpath for which the tool should retract to X21mm and then come out of the hole. But in actual, it first retracts to a smaller number i.e. X17.3mm and then go to X21 and then come out of the hole. X17.3 will cause my threading bar to smash in to workpiece. Do you have any idea what could be wrong and how it can be avoided? Would appreciate that. Cheers.
@mazatroltipsandtricks68165 ай бұрын
On the T-2 and T-3 controls, you need to put PNo0 line ID size same as the minor diameter of the thread. Check out my ID threading video.
@ryanroberts6362 Жыл бұрын
Not sure if you will see this since it an old video. Do you have anything that explains how to add a thread relief, specifically for my situation when the thread relief is against a wall. Thanks.
@mazatroltipsandtricks6816 Жыл бұрын
I have not made a video regarding a thread relief even though I do them all the time. I did a grooving thread relief on my ID threading video. For OD threads, I usually use a VNMG 332 insert tool and program a relief groove at a 45 degree angle behind the thread.
@ryanroberts6362 Жыл бұрын
@@mazatroltipsandtricks6816 I’ll try that, thank you
@phitran89802 жыл бұрын
It was nice video, very informative, and successfully delivery all the information to make an OD thread on the mazak. Hey, do you know how to chase the thread on the mazak lathe? Thank you.
@mazatroltipsandtricks68162 жыл бұрын
Trying to pick up an existing thread is very difficult. Newer Mazaks have an option to make that easier. I've never tried it myself.
@sudeepanchan4 жыл бұрын
Nice videos Phil. Fully informative. Thanks. I m a Mazak turning machine operator. new comer to Mazak from Fanuc Using Slant Turn 600 Smooth G. I hav not seen tool shape in simulation . Only path graph we r using till now. Is there any Idea to have tool shape also in simulation as you r using.?
@mazatroltipsandtricks68164 жыл бұрын
Unfortunately, Mazak took away that feature in the later controls. You have to do a simulation to see the tool now.
@tunaakgun60358 ай бұрын
@mazatroltipsandtricks6816 mazatrol t32-2.I've just started using Mazak, I'm taking examples from your videos, but I'm still at the beginning and I'm a novice, thank you also for your answer.
@ES-fr3yz7 ай бұрын
Important question,If I don't finish threads at end of shift and power the machine off,will it know where to pick up the next day?
@mazatroltipsandtricks68167 ай бұрын
I honestly do not know. You may want to run a test part on your machine to find out for yourself.
@jimmonk79364 жыл бұрын
Great video. I run a Nexus 350 II. Threading isn't my most fun thing to do. We have added the speed override option which works great for modifying speed during the thread cycle. The only thing I never figured out is the touch off of the tool on the tool eye vs the offsets. They are never theoretically zero on the X axis like a correct turing tool at the finish. They are always way negative on the OD or way positive on the ID from zero when threading only. I use .86603 x pitch for my thread height. I can get good threads but just can't trust to go to size or close off the tool eye. Also do you have any videos of how to chase threads for repairing if loaded back in the machine. Ours has that capability but nothing in the book to truly describe how to do it. Thanks for your videos. Older machine but the concept is the same.
@mazatroltipsandtricks68164 жыл бұрын
Our Integrex has the feature to pick up a thread but I have never tried it out yet. Old machines like my 10N doesn't have that ability.
@brianmatias4714 жыл бұрын
Jim Monk Does your machine come equipped with the Thread Position Teach option?
@jimmonk79364 жыл бұрын
@@brianmatias471 yes it does I believe. I have not tried it yet since we purchased the machine about 4 years ago. Haven't needed it yet but would like to figure that feature out.
@mazatroltipsandtricks68164 жыл бұрын
@@brianmatias471 I don't remember if it was included as a standard option or if it was extra for the Integrex.
@mariocortes1337 Жыл бұрын
Very good teaching 👍, congrats 👌 👏
@mazatroltipsandtricks6816 Жыл бұрын
Thanks for the compliment.
@jepkeklinge37784 жыл бұрын
Hey man, nice video again, coule you explain the surface roughness or make a video about the diffrance?
@mazatroltipsandtricks68164 жыл бұрын
Lower numbers are rougher feed rate and higher numbers are finer feed rate. Number 7 finish is slightly better than a 32 rms finish. It feeds a .031R insert at .0039" IPR.
@Andriuxa214 жыл бұрын
how do you remove the burr at the beginning of the thread? Are there special solutions in Mazatrol? In TCP? Thanks for the reform option and other useful information.
@mazatroltipsandtricks68164 жыл бұрын
You can remove the burr by rerunning the finish pass of the turning operation after the thread is cut.
@NewHartfordLocals Жыл бұрын
Phil I’m picking up a quick turn t6 with mazatrol T plus control . Is this control similar to what you demonstrate ?
@mazatroltipsandtricks6816 Жыл бұрын
Yes. Anything I am showing will work on the T+
@dgyldmark2 жыл бұрын
Hi! and thanks for your mazatrol school service! How do you thread an acme screw? ex screw elevator, "threading incremental i Z" ?
@mazatroltipsandtricks68162 жыл бұрын
ACME threads just need more threading passes but the program is the same otherwise.
@kevmarriott627226 күн бұрын
Hi, have you any experience with tracing/ picking up existing threads for reworking? I've been led to believe that it is possible on the T series controllers??? I know it's possible on later controller, would be super handy if it can be done on T series
@mazatroltipsandtricks681626 күн бұрын
@@kevmarriott6272 extreme pain in the ass to do it. Very risky operation because it's an eyeball job trying to line up the moving tool to the thread. Not recommended.
@miguelneves3982Ай бұрын
Hi Phil, i need to make ID oil grooves in a bush, been trying using the ID threading option after 30 mm pitch it doesn't look correct on the display Can the T2 manage this? any advice would be greatly appreciated Thanks
@mazatroltipsandtricks6816Ай бұрын
@@miguelneves3982 the display will look funky with an extremely coarse thread but it will work. Be sure to have PN0 0 line ID min set to the bore diameter of the hole otherwise the machine will retract X to 0 on last pass and possibly crash the grooving tool into the other side of the part.
@miguelneves3982Ай бұрын
Thank you much appreciated
@anh67903 жыл бұрын
Hi, Mr. Phil thanks a lot for your video! At the end of the video Could you please explain why are the tool offset-X 0.005 and 0.001? How do you know it, sir?
@mazatroltipsandtricks68163 жыл бұрын
The offsets were just examples. You will need to adjust your offsets accordingly to what your part measures.
@anh67903 жыл бұрын
@@mazatroltipsandtricks6816 Yes, I got it, thank you so much for the helpful videos. Hope you're still doing well during this pandemic time
@ceugepios3 жыл бұрын
Hey Phil Thanks for all you videos they've been a big help, Do you have any tips on Thread clipping in Mazatrol?
@mazatroltipsandtricks68163 жыл бұрын
I've never attempted it. I'm sure it can be done with a groove tool running a short threading process.
@ceugepios3 жыл бұрын
@@mazatroltipsandtricks6816 Hey Just thought I'd pop back in here and share what I found, if you want to thread clip a UNC thread it can be done by running a threading cycle with a start point a half pitch farther out than your original threading cycle, and ending at a full pitch in! keep your exit angle at 60 degrees and your grooving tool should have it clipped!
@mazatroltipsandtricks68163 жыл бұрын
@@ceugepios Thanks for the info.
@ozguraytekin3800 Жыл бұрын
Teşekkürler.
@tunaakgun60358 ай бұрын
Hello Phil, I can write the program as you showed, it works in simulation, but when I run the machine, it gives error code 635 ACCELERATION DISTANCE EXCEED. What could be the reason? Best regards
@mazatroltipsandtricks68168 ай бұрын
What control is on the machine? You can slow down the cutting speed to get it to work or change a threading parameter.
@tunaakgun60358 ай бұрын
@@mazatroltipsandtricks6816mazatrol t32-2.I've just started using Mazak, I'm taking examples from your videos, but I'm still at the beginning and I'm a novice, thank you also for your answer.
@neilmcdonald80114 жыл бұрын
coming from a fanuc background why are your tool offsets all 1 instead of t0101,t0202,t0404 etc?cheers.
@mazatroltipsandtricks68164 жыл бұрын
This machine uses offset columns like a grid. Offset column number 1 or the second offset column 2. Go to 18.34 in the video. You can see the two offset columns there.
@TuanNguyen-md8cc Жыл бұрын
Can u show us how npt is program on mazaktrol and threading option ??. Thanks
@mazatroltipsandtricks6816 Жыл бұрын
Ok. Thanks for the suggestion.
@jordansnyder28204 жыл бұрын
Would like to see some videos of a 40n t plus that’s what I have and all we cut is a36 anywhere from a 16x2.5 inch blank making casters to threading an 1.25 axel bolt😂
@mazatroltipsandtricks68164 жыл бұрын
I do not have a T+ controller.
@jordansnyder28204 жыл бұрын
Mazatrol Tips and Tricks still have useful info though
@75kGa4 жыл бұрын
Is the length value the total length of the raw stock (including what is clamped in the chuck)? Or is it just the visible stock protruding from the chuck jaws?
@tomaszspiszak1814 жыл бұрын
Raw material, plus I always add some more mm.
@75kGa4 жыл бұрын
Tomasz Spiszak thanks. So the length is the raw stock the entire raw stock. This includes what is clamped and visible ?
@tomaszspiszak1814 жыл бұрын
@@75kGa yes.
@75kGa4 жыл бұрын
Tomasz Spiszak awesome thanks. One last thing. What about the inside diameter values. If I have a raw solid stock and I am to bore a hole say 6inches as per drawing. Do I then insert this value of 6 in the ID value field?
@tomaszspiszak1814 жыл бұрын
@@75kGa put 0 in the first line for stock min dia. Check out his 1st or second video , there's a great explanation.
@robertzacharias65673 жыл бұрын
I need to turn a 1-8 left hand thread. Never have done it, I can't find any information on it. Any help is greatly appreciated.
@mazatroltipsandtricks68163 жыл бұрын
Same procedure as right handed thread. You just install a left handed tool in the turret and set the chuck direction to left hand. The threading program will be the same.
@robertzacharias65673 жыл бұрын
@@mazatroltipsandtricks6816 I'm guessing it needs a left hand insert holder?
@robertzacharias65673 жыл бұрын
A colleague said I could use a right hand and start into the part, 5 inches in this case. And thread back to the front. Will this work?
@mazatroltipsandtricks68163 жыл бұрын
@@robertzacharias6567 Mazatrol does not play well with that method. Get a left hand tool.
@kevmarriott627226 күн бұрын
using Mazatrol T32-2 I cut right and left-hand threads M50x1.5 with same tool & insert, just change Z start and finish points (swap them over) you do need to allow for approach/acceleration distance for the left-hand thread
@albertta20254 жыл бұрын
Is it possible if you can make a video on thread clipping on mazatrol and explain it in depth?
@mazatroltipsandtricks68164 жыл бұрын
Thread clipping? Not sure what you mean.
@albertta20254 жыл бұрын
@@mazatroltipsandtricks6816 I mean taking away the first imperfect thread with a grooving tool. For example on a 8 stub acme thread and using a grooving insert that's 0.125 to remove the first imperfect thread. I've also heard it being called a higbee thread too
@mazatroltipsandtricks68164 жыл бұрын
@@albertta2025 Got it. Never tried to Higbee a thread.
@ronaldfairhurst29143 жыл бұрын
@@mazatroltipsandtricks6816 I think he might want to know how to run a higbee cut
@rezanasirzadeh70033 ай бұрын
Nice❤
@jeanpierrelopez72484 жыл бұрын
Hello friend, look at me, I get an error in the subject of threading, the alarm is acleration distance exceed! And it won't let me screw.
@mazatroltipsandtricks68164 жыл бұрын
What controller do you have? I only have parameter information regarding the T-2 and T-3 controls. For the threading parameter, U35 controls the acceleration distance. It is set to a low value from the factory and that causes problems with threading at high RPM speed. The range of the parameter is 0-255, but I have mine set to 100 and it works fine. Other option is to slow down the threading SFM value in the program.
@vinayakpatil91603 жыл бұрын
We have to threading OD on 4 mt pipe so please suggest
@mazatroltipsandtricks68163 жыл бұрын
Not sure what you mean.
@derick34823 жыл бұрын
i like that single process option pretty clever
@mattiasarvidsson85222 жыл бұрын
how old is that machine ? :D
@mazatroltipsandtricks68162 жыл бұрын
1986. Still kicking.
@mohamedsalahcnc79104 жыл бұрын
Can you help me Can you send( pdf) program for mazatrol t32-2 control
@mazatroltipsandtricks68164 жыл бұрын
Not sure what you are asking for.
@mohamedsalahcnc79104 жыл бұрын
@@mazatroltipsandtricks6816 I need an EXPLANATION(PDF)
@mazatroltipsandtricks68164 жыл бұрын
@@mohamedsalahcnc7910 If you mean an operation manual, I do not have one.
@funwithak5m3 жыл бұрын
Not using M03 and M04 3D program
@mazatroltipsandtricks68163 жыл бұрын
Not sure what you are asking me.
@funwithak5m3 жыл бұрын
@@mazatroltipsandtricks6816 How will the direction of turning the spindle change CLOCK WISE and COUNTER CLOCK WISE
@mazatroltipsandtricks68163 жыл бұрын
@@funwithak5m It will cut either a right hand or left hand thread depending upon the tool.
@funwithak5m3 жыл бұрын
@@mazatroltipsandtricks6816 my machine is MAZATROL SMART
@funwithak5m3 жыл бұрын
It is created in the program you have created, it does not run, it is an alarm.
@saravananj3843 жыл бұрын
How to make NPT thread in this machine plz help me any one
@mazatroltipsandtricks68163 жыл бұрын
Male or female thread?
@saravananj3843 жыл бұрын
@@mazatroltipsandtricks6816 I got it sir I need one help from you sir
@saravananj3843 жыл бұрын
@@mazatroltipsandtricks6816 my mail I’d is j.Saravanan898@gmail.com ping me sir I want tips for making multiple serrations on outer dia
@christophercolumbus89443 жыл бұрын
@@saravananj384 NPT is just angle right?different diameter?s
@saravananj3843 жыл бұрын
@@christophercolumbus8944 yes how to do in mazatrol
@elitistseeker1258 Жыл бұрын
Well I just figured out why the apprentice crashed he hit reform instead redoing the whole process after comping the thread in 50 thou
@christophercolumbus8944 Жыл бұрын
you guys EIA at all? i need some help with setting up tools