Mazda 3 cracked screen replacement

[@billlove1691]

Tip: Don't take the 5 cables off the back of the unit... just unscrew the 4 screws on the top and leave the rest of the unit attached in the car. Way easier and quicker! Brilliant video and thank you again for the assist!

[@garrettgreen5642]

U gay

[@not-AI]

thank you for this I just popped those two clips underneath and the four screws on top and left the rest connected saved me a lot of time. All I'm trying to do is disconnect the touch screen cable to prevent the ghost touching I basically just needed the first 5 minutes of the video but anyways everybody here is a great help

[@hannahspence5857]

Disheartening to see how many people are experiencing these random issues with their Mazda. You would think Mazda would correct this issue. 10/10 on this video! Thank you for creating it. :)

[@joshymcdaniel9233]

They did / are if you have ghost touch or screen not working take it to dealer and they will replace u set special warranty they extended radio to 7 years only applies to 2014-2016

[@jacul3697]

@@joshymcdaniel9233 are they? Mine is 8 years old now

[@ijustneedmyself]

​@@joshymcdaniel9233But not to 2017, yay 😃😃😃

[@paulvasta5944]

Thanks for the video. For anyone considering doing this, if you are the least bit handy this is very do-able. Just a steady hand to pull off the dash vents. You don't really need to unplug and remove the whole assembly. Just take the four screws off of the main module and remove the display and dash mount. One important tip - don't just pull on the ribbon cable connecting the touchscreen to the PC board. There is a small white-ish latch at the point where the cable goes into the connector that you gently pull away from the connector. This releases the cable, and it easily slides out in one piece (unlike in the video). Connecting the new cable is just doing the reverse. The video is correct about the hardest part being how to remove the touchscreen from the bezel. The adhesive is very aggressive. Just try to get a thin plastic spatula or other flat tool under the touchscreen and slowly work it off. Too much force and you might break the plastic bezel. The glass will definitely crack as you go, so at that point there's no going back. I used Goof-Off to dissolve most of the remaining adhesive, then a little elbow grease with a soft piece of fabric will get the remainder. Once that is done, the rest is a piece of cake. Good luck!

[@eranmeir90]

Hey, I wanted to thank you. I think that so far this is the only relevant video I have found regarding this problem. My screen was also broken for some reason on 3 different spots and the touch screen wasn't working. Yesterday I replaced my screen the same way you did here, and for only 20$ and 3 hours of fun it turned out like new ! I am leaving here some more tips that I found helpful: * Use Isopropyl Alcohol and a razor blade when you're removing the old glass glue. * Let the Isopropyl Alcohol get into the cracks you're making with the blade and let it soak. * You can use a heat gun to melt the glue but this will cause the Isopropyl Alcohol to vapor so you'll need more of that. * Work while your hands and screen are inside a plastic bag that could catch all the tiny glass shards. * Don't panic when you notice another glass on the inner side of the screen and you think you've messed the touch screen - a new one comes with the new touch screen you're replacing this is the part that has the connector to the circuit board * When you disconnect the steel case of the circuit board try to work around from right to left, there are 2 "stoppers / holders" on both sides and you want to be careful. I used some leverage with a screwdriver and it worked for me. Thanks again, Your video was SUPER helpful !

[@BurlyNerdGetsTheWorm]

Good call on the heat gun! Took all of 30 seconds to pull the screen off in one piece!

[@mjtoscano3039]

Hello and thanks for your comments Did you buy 36 or 50 pins? Thanks for your help

[@JOELY713]

Very good tips. Another one is: the connector is secured by a thin white tab latch. You must push it out and up to pull and insert the ribbon connector without damaging it (ref video here @ time 0:33 kzbin.info/www/bejne/aXKrZHl5n5mdntU ). I only used a heat gun and a knife to separate the glass from the bezel with no loose shards but I agree working over a plastic bag is recommended just in case.

[@heatherk9]

That video about ribbon cables was helpful. Thank you!

[@hammereisen7493]

Thanks to your video we successfully renewed a Mazda 3 cracked display. We followed your video step by step. Without it, it would be difficult. 👍

[@mrcuic1]

Hi, do I have to disconnect the battery first or is it not necessary?

[@AlanRosenberg-p3f]

You made it possible for me to save so much money by sharing your techniques! Thanks for creating this. I think it is the only one that shows the actual screen replacement.

[@theboydslife7809]

Thanks. I looked on KZbin also and couldn’t find anything. That’s why I decided to document the process I took.

[@AEGHZEHJT]

Can I get a link for e bay? Can't find it

[@theboydslife7809]

@@AEGHZEHJT the link has been posted on a previous comment. Sorry if you need it later I will go try to find it

[@JenandPaul09]

Thanks for the walk-through! Just replaced my screen and this was very helpful. The worst part was getting that last metal bracket off- those tabs were a pain.

[@SergioMartinez-md1ip]

Thank you for creating this demonstration video. Also thanks to all of the commentators that gave feedback. I just finished replacing my screen 🎉

[@microzoom]

I bought the screen from AliExpress and installation was easy because of your video. Many thanks.

[@JohnnyPM14]

Went ahead and did this while installing CarPlay today. This was a massive help. Like other commenters said, throwing the screen in the oven then using a box cutter to cut from the outside worked wonders for getting the broken glass out.

[@joshualucas2412]

So I watched this video a couple times and in an hour I was able to change my Daughter's screen out. I used a heat gun to remove the old screen as well as a razor blade. Thank you so much for the video!!

[@theboydslife7809]

Awesome. Glad I was able to put the content out there

[@m0nd3]

Thanks for the video. It really helped prep me for the screen replacement. Just to add to/reinforce the tips for anyone else ready to embark upon this journey. - Leave the connectors attached to the back of the CMU - Just take the four screws off the top to remove the screen from the CMU and the two connectors to the screen - Be sure to disconnect the digitizer ribbon cable correctly (pull the white bit out and then up) - Heat gun and a razor blade works wonders for removing the screen adhesive

[@JD_Aguilar717]

So I've been doing cell phone repair for over 17 years. I have a 2014 Mazda3. I've done this repair. To separate the old touch screen from the frame. Turn your oven to the lowest setting. Usually around 180°F. When the oven is up to temperature. Put the screen in for 5 min. It will separate very easy. Also, you'll want to remove as much of the old adhesive as possible to ensure the new touch screen adheres properly.

[@adriandude85]

You’ve been doing cellphone repair for 17 years and never bought a heat gun?

[@JD_Aguilar717]

@@adriandude85 🤣😂 i have a heat gun. Ovens are better.

[@adriandude85]

@@JD_Aguilar717 then your heat gun sucks

[@JD_Aguilar717]

@@adriandude85 work smarter not harder. I guess no one taught you that. Plus the average person doesn't own one. 🤷‍♂️

[@adriandude85]

@@JD_Aguilar717 heat gun is literally $20. Using an oven then means you have to clean the oven. You’re the one working harder.

[@neldias1718]

So glad I found this video. My 2016 Mazda CX-3 infotainment screen came apart on the edges during -46 weather up here in Canada, Winnipeg. Perfect teardown video. I have a new screen. Thanks again!

[@Khell23]

I have the same car and my screen is cracked in the inside.. can you please give me the link where you bought the glass cover?

[@steveboulay8831]

did you find?? @@Khell23

[@steveboulay8831]

Waht is your info intertainment model number?? something like BHP1611... or K40005A... or KA0G669...??

[@rickb3674]

I wish your video was around when I had this problem a year and a half ago! I had the same thing happen. It was extremely hot outside and I forget to close the cover for the sunroof. When I got back in my car I noticed a mark on the digitizer. I searched the Mazda 3 forums for info on how to get it fixed but they just recommended taking it to the dealer or buying an entire display unit from eBay. I knew there had to be better way so found a replacement digitizer for less than $20 and swapped it out. The new digitizer is clearer than the OEM one ever was. Too keep this from happening again I keep an old hat on my dash and use it to cover the screen the car is going to be parked outside for more than a couple minutes.

[@theboydslife7809]

Great idea on keeping it covered.

[@foothillspropertymanagemen4761]

Dude, thank you! There was a service bulletin from Mazda to replace the delaminating screen, but of course I bought the car right after that offer had expired. So either a $900 OEM display from Mazda, or a $23 eBay gamble. This worked perfectly. What's funny is that I didn't know it was actually a touch screen since that function hasn't ever worked. Once I got the screen separated on one corner, I was able to run a razor gently along the seam from the OUTSIDE and cut the adhesive. Razor then used to get the old adhesive and foam off, followed by isopropyl and a rag. Once I cracked the screen, I realized there was no going back, but it worked perfectly. Thanks again.

[@barbaramolina7167]

where did you find it for $23? if you could send me a link, im trying to find it but no luck! thanks in advance

[@shakes268]

$900? My dealership wants $2000 to replace my CX-9 display

[@MichelLaplante-m4o]

@@shakes268 De Grâce fais le toi-même, crackpot les concessionnaires

[@magicmaybach]

​@@shakes268 Dealers are just thieves in disguise mate, same in the UK. Wouldn't use a dealership if it was the last place on the planet!!

[@jalo6292]

Followed you step by step and got it done. Saved alot of $. Thank you. Cheers.

[@carogasm]

My screen was broken, I called Mazda and they told me it was $800 to fix 😂 I then asked how much is the part alone and they told me $450 for the 2017 Mazda 3. I laughed in their face, ordered the part on EBay for $150 did it myself. Thanks

[@MichelLaplante-m4o]

Moi aussi j'ai fait pareil

[@Seskoi]

Me too but for 40$ :D

[@matthewjamesonjr]

Just did this today, thanks for the upload! Only thing that really sucked was the clips just above the glovebox. Dropped the glovebox and reached back there with some small needle nose pliers to get them to release

[@simg7584]

My dealership quoted me $1700 plus installation lol. Thanks for the vid

[@edwardshupe7420]

Hello everyone! Definitely a time save to just remove the 4 screws on the top. Fairly simple! Took me 20 minutes from start to finish! Thanks everyone for the tips and instructions 🤘🤘

[@mscookie3613]

I live in Florida (typically 70°’s + and humid as hell) and we’re up north visiting family and my screen just cracked from the 17° weather from this years winter storm. Thank you for this video I will be following it when I get home! 🥲

[@theboydslife7809]

Dang weather. Good luck with your repair.

[@markgbastin]

Amazing, just finished mine. Took just about an hour after watching this. Thanks a lot

[@madresults_952]

I just replaced my screen with your video. Thanks a ton for this great video!

[@MiniBOJ]

Life saver! Thank you. I just finished mine, just because of your video it took me about an hour! Amazing. Thank you very much!

[@nigelbowen6299]

Thanks for the instructional video. All worked great, but can defiantly recommend using a heat gun to soften the glue to remove the old screen and disconnect the ribbon cable just before removing the CB by sliding the holding bar to release the cable.

[@Istartedthefire87]

Did the same repair, your video walked me through the whole process, thank you .

[@craigj6916]

Got a link to the screen kit?

[@СобачьяСасиска]

Thank you for the video! Very helpful in solving the problem.

[@charlesduncan2051]

great video, I would add that you can soak the plastic frame in hot water, then take a razor blade (or sharp pocket knife) to the adhesive. the adhesive seems to come off all in one strip more often when it's warm and soaked. I lost a 10mm bolt down my air vent though, full cost to repair at home was around 25 for a new screen on amazon and a new ratchet set which was around 40 dollars. took about three hours with the trip to home depot.

[@SenorBezi]

In my 2014, my touch screen was bugging out hard so much that I couldn't use my gps so I disconnected my touchscreen ribbon cable 5 years ago. A few days ago, it was below freezing in the morning, but rose to 60 degrees in the afternoon and I came out and it was cracked from the temperature rapidly changing. Definitely going to do this now.

[@geodesocio561]

I like that you were prepared, but didn't rehearse :-) You did a good job! Some thoughts: You tore the ribbon cable because you didn't release the clip/clamp part of the circuit board connector. You should have removed the metal bracket before removing the ribbon cable. You were lucky. If you damage the clip/clamp on the circuit board, you're toast. The clip/clamp is hinged and lifts up to disconnect, and pushes down to clamp the ribbon cable connections together. Lift carefully from center of clip with fingernail or spudger tool to retract the ribbon, and press down after you've pushed the ribbon cable home. Do that before you put the metal cover over the circuit board, it's easier that way. You can use a heat gun to make the adhesive soft by warming it up a bit (don't warp the frame)... removes easier. Also use denatured alcohol instead of rubbing alcohol, if you have it. You should wear exam gloves while working on the touch panel and display screen. Easy on the Mazda, can be a real long process on some Toyotas. My daughter's dealer said $2000 to fix. Criminals. It's a defect and should be recalled. Thanks for the video!!

[@theboydslife7809]

Thanks for the info. Yeah the ribbon was stubborn.

[@not-AI]

apparently not reconnecting the touch screen cable will prevent ghost touching issues. I'm experiencing like a lot of other people the ghost touching where the screen likes to randomly do its own thing and this video was helpful in finding out how to remove the touch screen just so that I can disconnect the touch screen cable

[@GrE3kGoD]

Not sure if it's been mentioned but when i did this backup camera wouldn't work. Before tearing it back apart i found you can do a hard reset on the screen by holding Mute + Nav + Back (the hand controls by shifter) button until when goes off.

[@Beanlekin]

Thanks for the awesome video! So good to find one that hasn't been pre rehearsed but also isn't full of a bunch of waffle. For anyone else attempting, when you remove the ribbon, get you fingernail in behind the little white clip to pop it backwards and then the ribbon will slide right out. That's what holds it in place. 😊

[@alejandroerentxun9689]

My touch screen was cracked like yours, I went to dealership and they wanted to replace the touch panel & display screen for $600 usd 😳😳 After check your video and also visit different websites to get the correct touch panel I followed your instructions and got the same fucking result 👌🏼👌🏼, my touch screen works perfectly & looks amazing 😀😀, thanks a lot buddy..!!

[@iandavidharwin]

Which website did you use?

[@AmodSachintha]

Thanks for this, replaced the touch screen on my Axela as well!

[@TheForge101]

Well have a 2018 mazda and the heat just started doing this to my screen last month. Its not 1/4 of the screen. Taking it into mazda next week to see if they will extended warranty it. If not ill be doing this myself the day after.

[@JuancarlosMontes-m3t]

Muy bueno, estoy a punto de comprarme un Mazda 3 y probablemente me sirva el vídeo, gracias compadre

[@viejo1955]

this was a great guide, the only thing I did different was use a heat gun to soften adhesive and use a spudger.

[@theboydslife7809]

It crossed my mind just didn’t want to overheat something that didn’t need to be brought to temp. But yeah some temporary heat would definitely make it easier. Good tip

[@PicassoOficial]

Thank you for the video, I'm going to try it, greetings from Mexico.

[@koroshkabir904]

After replacing the touch screen, I found out that the touch screen was not cracked, as it looks like. It was the adhesive between the outer glass and the touch panel that is not sticking well and it looks like the screen is cracked, so you don't have to buy a new screen. you can take the outer glass and touch panel apart using hot airgun, then remove the adhesive with some alcohol and then put them together again with UV glue.

[@theboydslife7809]

Nice, in my case it was cracked pretty bad.

[@michaelalvarez1037]

what kind of glue should i use?

[@theboydslife7809]

@@michaelalvarez1037 you don’t use glue

[@michaelalvarez1037]

@@theboydslife7809 what kind of glue

[@koroshkabir904]

@@michaelalvarez1037 Loca UV glue which is used for smartphones LCD display, then put the screen under UV light for about 15 minutes so it sticks.

[@glorialeyva4066]

I need to do this myself, thanks! Dealership was going to charge me $600!!! Screw that

[@tonymartucci3384]

Awesome video! Thanks for all the info.

[@billking7894]

Great video..just did mine on 2015..mazda 3..I used a heat gun and oven Mitt to remove glass.thx for the info

[@j3cu]

I went to the dealership and they wanted to replace the entire computer..for $500ish...Thanks for the video

[@theboydslife7809]

Yeah dealerships are cray (I use to work for one ) this is a way cheaper option

[@joshymcdaniel9233]

Never go to dealership always check eBay or junkyards first ALWAYS! Most stuff is very simple a few screws or clips hold it in’ just don’t forget where screws go etc’ take pics etc rite down your disassembly steps like step one left screw then put a piece a tape with #1 on counter etc put screw on #1 then u can just reverse when putting back together

[@Istartedthefire87]

Same so I did it at home for 40 dollars

[@christianlorentzen4124]

Nice to know it’s possible. I got a Scion Ia which uses the same screen.

[@christianduguay8878]

Merci beaucoup pour votre vidéo chez mazda me charge 1600$ pour la réparation j ai commander la vitre sur amazon 45$ j ai suivi les étapes de votre vidéo et ça fonctionne comme une neuve

[@bryancardenas5470]

Hey man, thanks so much for the video! I just finished doing the replacement following your procedure. My only note is for whatever reason things did not go as easy for me (one of the first screws on my head unit were stripped for some reason???) as it did for you haha. Might be an issue from my end though. Thanks again!

[@darcyhines1786]

Blow dryer or heat gun works well it will peel right off . Easy. Careful if using a heat gun gets hot faster.

[@gptriplesticks]

Would the process be the same for a Mazda 3 that doesn’t have a touchscreen? My car is a 2014. Thanks

[@theboydslife7809]

@@gptriplesticks are you sure it’s not a touchscreen? Mine touchscreen didn’t work once the screen was cracked. After the screen replaced, it worked as it should.

[@daximusr]

Thanks so much for the video! About to do the same repair.

[@BakrTouati]

does the broken touch screen give a sign of check engine?

[@avivcaspi4132]

Hi,, 5:36 I did not understand how I disassemble the last part (with clips) How did you do

[@theboydslife7809]

After removing the screws then just place a small screwdriver underneath the clips and lift up. Believe there’s 4 of them.

[@avivcaspi4132]

okay, thank you for help..

[@ddjerusalem]

hi , its the same screen for mazda 2 2015?

[@theboydslife7809]

Yes

[@andymedina323]

Thank man you help me fix my screen from my 16' mx5

[@Megadebt]

Thanks I just can't get those four metal clips on the sides of the mount how do you get it removed? I tried a screwdriver but to no avail

[@theboydslife7809]

Had to use a couple little screwdrivers to keep pressure on the clip as you release the pressure on the other clips. Hope that makes sense

[@pedropedroza5617]

Hello good video and helpfull, hoy do you separate the stereo in minute 6:00?, thanks from México

[@sarahe4129]

Yup…it’s off screen and I’m lost

[@mrcuic1]

Hi, do I have to disconnect the battery first or is it not necessary?

[@oozboy]

Thank you so much bro 🙏

[@dianapena9779]

hello, I have this problem with my mazda 3 grand touring 2016. I would like to know where to buy the display and if you can install touch because the one that comes with my car is not touch. Thank you

[@manolotrovador]

Gracias! saludos desde México. Me va a ayudar mucho este video

[@Rio-d4v]

Can you tell me the name or type of kit you purchased from eBay? I have the exact same issues on my screen with the cracking and would like to replace the screen. Thanks.

[@theboydslife7809]

Not sure off the top of my head at the moment. But the link has been posted in the comment section somewhere.

[@matthewcutler_tx]

Boydie can't you just put the link in the description mate?!

[@imabigfanshow783]

This just happened to my son’s 2016 Mazda 3. Looks like this may be in our future.

[@theboydslife7809]

@@imabigfanshow783 luckily it’s a easy job

[@kaipaz10]

The 10 mm bolt is FREAKING tight. I can’t loosen it!!!

[@theboydslife7809]

@@kaipaz10 wonder if somehow they rusted in there ?

[@Umdringside]

Same stuck on that

[@JDuBz815]

Mine cracked this winter -5F at Christmas. Nice to know I don't need the whole unit.

[@3srs5U]

Thanks for this, I have exactly the same repair to do. Nice to know it'll only cost me the ~$20 for new glass. Next step is for me to stop living in a desert that gets to 125 degrees in the summer so maybe my screen doesn't crack again. -_-

[@theDarweesh]

Dubai??

[@-I-d-a-n-]

Hi. Where did you buy the replacement Part?

[@juliekim7775]

Good question, I’m also wondering where you can buy the replacement kit

[@magicmaybach]

E bay.

[@aurellleshi9779]

Great video thank you

[@sigi_aoeageofempires2defin765]

Min 11:56 y broke the flex in your right hand the small one :( do you have an idea how can i solve that? where could i buy that flex?

[@sigi_aoeageofempires2defin765]

Help pls

[@bananaman30]

the way you ripped the digitizer cable gave me a heart ache as a tech for future reference those digitizer or ribbon cables have a flip siwtch hold them down you just have to flip it up

[@ALIFOKTAFIAN-RCH]

My mazda 2 somehow had tons of dust under the glass housing, can i open the glass frame to get rid of the dust without replacing it with the new one?

[@josephochoa5230]

Is there a way to do his without taking the entire unit out of the dash? Could you heat up the adhesive and remove the glass and replace?

[@theboydslife7809]

Not sure how you would, but taking it out takes less the a minute.

[@wariskhan8350]

I'm about to have the CarPlay update installed in my vehicle and the part is coming in around an month from now, do you think I would still be able to follow this video exactly?

[@theboydslife7809]

Not sure to be honest with you. If it involves removing the head unit then yes

[@wariskhan8350]

@@theboydslife7809 Sorry I misworded the question lol. I meant I’m getting the car play retrofitted in a couple of days but in about a month I’m hoping to replace the screen so I have no clue if I can actually do it since they’re retrofitting the car

[@bigrywhat]

Definitely needed this video. Thanks

[@vallejo6206]

Thanks man for the video, I have the same problem on my Mazda!

[@bh2005]

Hi! What year mazda is yours? Will it work on a 2014 3rd gen?

[@magicmaybach]

Yes, same procedure. Easy job and a cheap fix, unless you like being robbed by legalised highwaymen aka dealerships!!

[@yosofya]

thanks for the great tut. Would appreciate it if you share the link for this exact screen so i get no surprises when i purchase it :D

[@theboydslife7809]

Don’t have the link right now but it is posted in the messages somewhere

[@redposthill7253]

Awesome video - thanks!

[@gurmeetsinghdutta1237]

I was trying to update it to a new firmware and i turned the car off while updating. Now the screen is black. I took to the mazda service centre and they couldn’t get it back to the normal. I need your help😢

[@theboydslife7809]

Sounds like a programming issue. But may have fried something also. I really don’t have a fix for that. May be about to find a cheap used screen on eBay. If you took it to Mazda was they able find that the screen was as receiving power and signal? If so yes you will probably need a new one. If not may be a computer issue.

[@gurmeetsinghdutta1237]

They did a diagnostic test and saying the system is corrupt and you need to buy a new one for $2600. I am thinking to buy it from a write off vehicle. Is it worth ?

[@theboydslife7809]

@@gurmeetsinghdutta1237 not worth what they are charging but definitely worth trying to find one on the the used market.

[@joshymcdaniel9233]

Search 2014-2016 mazda 3 bricked cmu It’s called bricked updating software is dangerous if u don’t know how to do it’ lots of videos / fourms showing how to fix a bricked cmu

[@joshymcdaniel9233]

@@gurmeetsinghdutta1237 if u find one at a junk yard do it’ prolly can pick it up for $50

[@danterobles3140]

What is the part number I can not find it on eBay

[@theboydslife7809]

Not sure of the part # but they are all over eBay. Someone posted a link somewhere in the comments .thanks for watching though

[@richieriched]

does this work for the 2017 mazda 3?

[@theboydslife7809]

No

[@ramonmorales2502]

where did you buy that screen replacement?

[@timdybala1719]

Ebay but don't know what he used to find it.

[@etchesketch]

How did you remove the metal bracket at 6:03?

[@theboydslife7809]

It has tabs on the outside of the bracket that you need to pry up to release

[@etchesketch]

@@theboydslife7809 Thanks. I struggled and got it eventually using various screwdrivers and picks.

[@TopReactions.]

Give us the link of touch screen to buy it

[@johnmarshal4096]

I woke up for work an noticed that spider web looking damage, in the corner of my screen. I'm a bit upset considering cars should be suited for any environment. It did dip below 30°s that night so I assumed it was because of the temperature. Because that's the only factor that I could come up with. How do I prevent it happening again or getting worse?

[@magicmaybach]

You can't, it's a common delamination fault down to the manufacturer, they, however, will come out with any old bullshit to avoid taking responsibility and will instead try to persuade you to part with hundreds of dollars/pounds etc to replace the entire unit! 😮 Easy and cheap fix to DIY thankfully.....

[@YTOS86]

Can I have a link to the part?

[@MrSuperiorTech]

Same

[@akire564]

I did not know this was commun for the mazda cars I also have this same problem

[@williamdixoniii]

To everyone having trouble trying to get that metal bracket off that holds the plastic bezel to the actual screen. Move it to the left or right then pull back. Will pop right off.

[@JaimeVenegas-f7m]

This happened to me exactly! The temperature dropped and it cracked my screen!

[@cyanideaside]

I did this repair and now my screen wont turn on. I connected all the wires you did and triple checked. The radio music still plays but the screen is black and theres a high pitched noise coming from the radio. Does anyone know what I could've did wrong? :(

[@theboydslife7809]

Wish I could help with this. But if you did plug everything back in it’s hard to diagnose with looking at the car. First start simple and check fuses make sure you didn’t short anything then take back apart to make sure everything is actually plugged in all the way. Then check the ribbon plug make sure it’s not upside down or ripped

[@cyanideaside]

@@theboydslife7809 I appreciate your response. For anyone else with a similar issue, recheck the ribbon wires like mentioned. My issue was that the ribbon wires on the left and right side of the screen were moved around when I was taking off the metal mount and one of those wires controls the display of the screen. Thank you!

[@cannonjanes994]

@@cyanideaside Man I have the same problem!! Followed the instructions and now I have a black screen! I tried disconnecting the ribbon cables and re-installing them but that did not work. I will try again and cross my fingers. If it works I will add to this comment. So frustrating

[@dannyg.6431]

Do any of you guys have an ebay link to this exact one?

[@theboydslife7809]

Not sure if the is the exact on I used but is the same thing www.ebay.com/itm/394280992665?chn=ps&_trkparms=ispr%3D1&amdata=enc%3A1wrCNaP3FSoqqFR9tEiOe7w18&norover=1&mkevt=1&mkrid=711-117182-37290-0&mkcid=2&mkscid=101&itemid=394280992665&targetid=1644837434523&device=m&mktype=&googleloc=9031695&poi=&campaignid=16743749222&mkgroupid=138744546207&rlsatarget=pla-1644837434523&abcId=9300842&merchantid=644208330&gbraid=0AAAAAD_QDh8Xyd6o1s9v15VLMt72rGfGZ&gclid=EAIaIQobChMIwN-P3ouq_gIVZZBbCh0KhQvUEAQYASABEgIL1fD_BwE

[@dannyg.6431]

@@theboydslife7809 thank you!

[@sarahe4129]

Any tips on getting the “clips” off around 6:00? Mine’s definitely not falling apart.

[@theboydslife7809]

Sorry just saw this. One at a time and keep pressure lifting up while you pop the other open. If you let off the pressure they will re-clip themselves. Not sure if that helped or not.

[@sarahe4129]

@@theboydslife7809 Thanks! I eventually got it. The clips were a little mutilated, but it all went together fine. Thanks for the video!

[@theboydslife7809]

Always great when you can do something yourself. Great job

[@adilcanada7862]

I went to the mazda dealership for screen replacement on my 2018 Mazda3 gt i want bigger one with android auto they say you can't replace it because it design like that so its impossible to replace it is that true?

[@theboydslife7809]

Nothing is impossible, but that isn’t something a dealership would offer.

[@panukasz2291]

Mistrzu czy ten ekran jest taki sam jak w maździe cx3 z 2015 roku bo niby wszędzie tak piszą

[@magicmaybach]

Yes, same procedure...

[@domademedame]

Wow where you bought it ??

[@martinking3064]

Can you give the part info you found

[@pauliefaris1578]

Hi I was wondering what the kit was called that You got off eBay

[@theboydslife7809]

7” touch screen glass for 2014 2015 2016 Mazda 3. That’s the way it worded on eBay. Also may be there part number BHP1611J0D

[@ratherbesurfing333]

@@theboydslife7809 thankyou for this info just place my order

[@cristianalexisrocuantveneg4993]

Eso me pasó con mi pantalla, al parecer por el sol, alguien sabe si al reemplazar por la nueva pantalla vuelve a suceder? o solo era con la pantalla de fabrica?

[@theboydslife7809]

This one has been good since I put it in.

[@jimcrow8562]

Is there a reason you didn't use the toolkit that came with the replacement screen?

[@theboydslife7809]

Nothing it came with would have worked any better then tools I already had.

[@flippedbinary]

@@theboydslife7809 I'm about of buy a replacement screen to fix my display. What tools come in the toolkit that came with the screen? Or what tools do I need to do the repair myself?

[@hussain.514]

how can i find this part of screen?

[@theboydslife7809]

Not sure what you mean. But you can use the link in one of these messages to the eBay link or just search for the screen replacement on eBay