©😉Maze Solve Full Tutorial | Three Ultrasonic sensors wall follower with code Subscribe, Dhaddammm

[@deepakbains6755]

Can we made all in one smart cart .line follow, obstacles avoiding and Bluetooth control..plz help or make video of that..

[@DhadamRobotics]

Yes, you can do all in one but some time For controlling is SO , difficult , or about video Is like watch minimum 3hours video or uploading for me is too directly. 😳

[@Dina-ug6bq]

Bro....whether we can use this same code for L293d motor driver shield or we should do some modifications in the code?....

[@DhadamRobotics]

Yes, you provide in library or define motor driver in code

[@Nikhil-dp2mw]

Actually im doind it for my science exhibition, so if u can help me it would be great

[@DhadamRobotics]

Yes

[@jinxstall4178]

what is the rating of motor used? and what should i use to make it faster?

[@DhadamRobotics]

My opinion is used low rpm motor for best working. I used 30 rpm

[@tuncfreeman]

@@DhadamRobotics I guess changing "define PWM 150 to 250 smthg" will make the reductor dc motor (250rpm default ones) turn faster? Thank you

[@DhadamRobotics]

Set as per Requirements for better performance . Watch my other 2wheel driver maze solve . Same concept also theirs.

[@alaasayed4587]

the link of code doesnt work ... can you send it to me i need it

[@DhadamRobotics]

Sorry ,dear this work ,I also make other same robot , check here Circuit diagram present in this video: kzbin.info/www/bejne/d3vOhpmKir2re6c

[@DhadamRobotics]

Google GPS Tracker: kzbin.info/www/bejne/q4qXo2injdp_Zq8 Innovation For Accidents Control : kzbin.info/www/bejne/oIvaYoKer8h7Y5o Mind control car: kzbin.info/www/bejne/eoimgqp7mJh1erM Joystick Control robot: kzbin.info/www/bejne/n2mwm4qKaNSZors SMS Control Robot: kzbin.info/www/bejne/pYnUkKCFic1kZqs Home Automation: kzbin.info/www/bejne/j4HdeIZ6bK9gfJY

[@charlesreyes4410]

Hello sir, my board is different from what you are using. Im using arduino with pic1650 Micro controller on it So I cant plug the 5v of the motor driver to the arduino... It is possible to just plug the 5v of the motor driver to the 5v of the arduino which located to the side of the arduino board?

[@charlesreyes4410]

Or should i plug the 5v of the motor driver to the vin of the arduino board

[@DhadamRobotics]

@@charlesreyes4410 Yes , but make sure otherwise board can be damage

[@aashutoshkumarjha5899]

How do you make it turn so perfect Can you share logic of just turning

[@DhadamRobotics]

This is trial or error method , I try to do maximum perfect , but you can try with change duration ratio

[@aashutoshkumarjha5899]

@@DhadamRobotics so turning is based on delay not on sensor values?

[@DhadamRobotics]

@@aashutoshkumarjha5899 both delay as well as Duration ratio of sensors

[@lionlion4761]

nice done job very awsome application

[@DhadamRobotics]

Thank you

[@vikyjene]

You are connecting the positive of the battery to motor shield and negative from motor shield to gnd of UNO board and third connection in the motor shield is connected to which part of the UNO board

[@DhadamRobotics]

This is 5 v output pin ,used for arduino +5V pin

[@Nikhil-dp2mw]

Which motor did u use?? 12 volts?

[@DhadamRobotics]

If low arpm then use 12 v , but 100 rpm use 7 v

[@nikunjbaraiya3140]

Ha dhadam robotics ha Mr. Mayur & Kaushik

[@DhadamRobotics]

Thank you Bhai , thodo watch time ghate che ,share karje bija video

[@shilajaaneesh2363]

Can you please tell the measurements and the angle of the board you used to fit ultrasonic sensor

[@DhadamRobotics]

30-45 degree

[@PhiNguyen-im6qe]

Can you use the SRF05 ultrasonic sensor, bro

[@DhadamRobotics]

Hcsr 04

[@rohitnehra9519]

I have made this but my robo doesn't turn after detecting wall plzz help me asap coz i have to submit it for my clg exhibition

[@DhadamRobotics]

Ok check duration rate , or change some , so you robo now work then earlier , also provide delay , so you work as per Requirements because Rpm of motor is dependent on turn rate, thank you for sharing problems

[@rohitnehra9519]

Okk thank you sir

[@rohitnehra9519]

7977650567 this is my number plz contact me And will this work on sr05??

[@dharmeshss3710]

This programming code work for the Arduino mega 2560 ?

[@DhadamRobotics]

Same ,only change when you upload code in board that time select board arduino MEGA 😊

[@dharmeshss3710]

@@DhadamRobotics connection also a same?

[@DhadamRobotics]

@@dharmeshss3710 Yes , check other video , two wheels maze solve , where present diagram in video

[@dharmeshss3710]

@@DhadamRobotics thank you so much😊

[@DhadamRobotics]

@@dharmeshss3710 No mention dear 😃

[@Ann-xr4kb]

Which algorithm have you used in your code?

[@DhadamRobotics]

C

[@Ann-xr4kb]

​@@DhadamRobotics how to buy the code?

[@DhadamRobotics]

@Ann-xr4kb done donation first dear then after you access it

[@saagarpanta9490]

sir will you give me the code for aurdino,that scans qr code and sends message to mobile .

[@nairanahin6562]

Sir may I have the code and circuit diagram of your project please!?

[@DhadamRobotics]

Please code is given in Descriptions bottom see , or connection details on video

[@nairanahin6562]

@@DhadamRobotics Thanks 🙂

[@sofiasalazar1775]

Hi, could I ask you how you joined the 3 sensor jumper and converted them into one to connect them to GND, what kind of jumpers did you use?

[@DhadamRobotics]

It's ,a simple connector like a bread board , for connect all +5v or gnd of sensor because Arduino have only 2, +5v out put pin

[@sofiasalazar1775]

@@DhadamRobotics Yes, I understand why you did it. But I don't know how did you do it... I mean you only use jumpers? Please can you tell me how do you joined them

[@DhadamRobotics]

Join in parallel all +5v or gnd jumper

[@fang_X_EDITS]

Can we use 9 volt battery for the experiment with same items as used by you?

[@DhadamRobotics]

Not used 9v battery , because not sufficient capacity so not working

[@user-tz8qv7ov4r]

And can u show how the circuit was connected I mean the whole process and the schematic of the connection

[@DhadamRobotics]

Yes ,full details are given in Video , step by step process shown in Video ,future any quarry tell me, I always help my friend . 😄😊

[@user-tz8qv7ov4r]

Dhaddammm Robotics yeah but it would be better to put the schematic of the circuit bro coz it’s easy to follow

[@DhadamRobotics]

@@user-tz8qv7ov4r Yes ,but some time Diagram is not maintain as per robot condition so,change connection ,So I am not put diagram

[@user-tz8qv7ov4r]

Dhaddammm Robotics I hope that I get right connection coz when u re connecting the sensors it isn’t clear where u put ur connection wirs

[@DhadamRobotics]

@@user-tz8qv7ov4r I write Text about connection wire where joint (At left top corner) follower this connection , because this same as my video connection. Further any quarry what up me

[@DhadamRobotics]

Maze Solve Circuit diagram in this video: kzbin.info/www/bejne/d3vOhpmKir2re6c Google GPS Tracker: kzbin.info/www/bejne/q4qXo2injdp_Zq8 Innovation For Accidents Control : kzbin.info/www/bejne/oIvaYoKer8h7Y5o Mind control car: kzbin.info/www/bejne/eoimgqp7mJh1erM Joystick Control robot: kzbin.info/www/bejne/n2mwm4qKaNSZors SMS Control Robot: kzbin.info/www/bejne/pYnUkKCFic1kZqs Home Automation: kzbin.info/www/bejne/j4HdeIZ6bK9gfJY Gsm home Security,Sms : kzbin.info/www/bejne/nYHFaYh6oZKVY68 Gsm send Sms for Exotic Gas Home Automation: kzbin.info/www/bejne/eIPPdZ6HqtWSeZY Check other video: kzbin.info/www/bejne/g6C4aKeLq51-aac Self balance robot with code: kzbin.info/www/bejne/gHLHq2SAqN-md9k Joystick Control Robotic Arm: kzbin.info/www/bejne/fXTTp42KnJKlsJI Gsm Fire fighters systems: kzbin.info/www/bejne/gH7WhqV3i5JnY6M Auto irrigation SMS Control: kzbin.info/www/bejne/rXK6g36QfspooLs

[@maricruzolmos2578]

Can you share de code? 🥺 Is for my school proyect 😔

[@DhadamRobotics]

Check description bottom part , Code present their

[@birdost8448]

@@DhadamRobotics thank you for everything.I learn many things about the coding thank you so much . 02.28AM in 2020. From Turkey.

[@DhadamRobotics]

NO mention dear, my aim share ideas for beginners.

[@prasadpatharkar65]

how can i convert this bot in an object follower bot? i wanna make a object follower so what changes should i do in the code?

[@DhadamRobotics]

Sorry ,dear this code is not perfect for object follower,you use other code ,I Work on them after two days I upload video for object follower ,I Make object follower three type using different sensors ,once visit my other video .

[@prasadpatharkar65]

@@DhadamRobotics so are u going to upload a video on object follower bot after 2 days .???

[@prasadpatharkar65]

If u r going to do so can u please do it using three ultrasonic sensors ????

[@DhadamRobotics]

@@prasadpatharkar65 Yes

[@prasadpatharkar65]

@@DhadamRoboticscan u try making it with 3 ultrasonic sensors , it will be of great help!

[@riad_107eee8]

Kindly, can you tell me that how can i get the arduino code of this project? I'm going to construct this project very soon.

[@DhadamRobotics]

Available at description page see bottom of description

[@riad_107eee8]

thank you dhadam robotics

[@AiQuantitativeTradingSystem]

very nice friend thank you .please can give the circuit schema?.

[@DhadamRobotics]

Code available available description page bottom part ,or follow video details ,for connection details,because diagram not with me

[@tuncfreeman]

After all of the instruction videos around the web, this is the best I can find. Great work!

[@DhadamRobotics]

Thanks dear.

[@tuncfreeman]

@@DhadamRobotics Can I put a "delay(2000);" to every move it does? Or before " forward();" commands? I am making experiments to make the robot move more carefully with lower PWM speed. ?

[@DhadamRobotics]

Yes , but if speed high then reduce pwm value , or delay also change as per Requirements . Because I set delay as per my condition.

[@mdaravee]

thanks for the wonderful tutorial ,i am working on the similar projrct but i am using 5 ultrasonic sensors 1 dc brush motor ,1 servo for steering. but i am having some broblem with my motor it doesnt want to turn .would you kindly assist me .. if you can i can upload the code. thank you in advance

[@DhadamRobotics]

First check with 3 Ultrasonic Sensor working or not. Because first start your robot after do changes.

[@user-tz8qv7ov4r]

But what kind of battery u used and how many volt it is

[@DhadamRobotics]

Here I am Using lipo battery 7 v(2cell ) , you can use also 12v battery(rechargeable high mah

[@cristianjimenez2394]

the scheme please... This is the Arduino UNO?

[@DhadamRobotics]

Yes, but different type or low cost then original arduino uno R3

[@misstwist1320]

It is a clone arduino uno in india u can find it around 3 $ to 5$

[@DhadamRobotics]

Your Mean arduino board ??

[@misstwist1320]

Yes

[@pinakshadhukhan4235]

Sir can i get the circuit diagram of this project???

[@DhadamRobotics]

Sorry, but you check code you understand circuit otherwise watch full video

[@prasadpatharkar65]

Sir when i tried to compile the code it is showing "lt was not declared in this scope " " amp was not declared in this scope " can u please help me with it.

[@DhadamRobotics]

Send photos of arduino error on my what's up

[@DhadamRobotics]

Once try with Android arduino app

[@tatevaramyan9330]

Please can anyone say .what the comolexity of the algorithm is equal?

[@DhadamRobotics]

Not same for all ,dear

[@tatevaramyan9330]

In your project was used left hand rule ? What is the complexiti of that left hend rule algorithm.?

[@hoodiewalahip-hopcenter8684]

Can I use little part of this video (0:00 - 1:00) for my compilation video. I'm making a compilation video of best Arduino based projects. So I want to add your project in the list. Because your projects are awesome. So I need your permission. Please reply.

[@zulfaafnantuba7169]

Can i use 7.4v 2600mah lithium ion battery instead of a lipo battery

[@DhadamRobotics]

Yes

[@zulfaafnantuba7169]

How much mah it should be?

[@zulfaafnantuba7169]

Battery should be in how much range of volta and mah ?please reply

[@DhadamRobotics]

Used if possible more than 2000 mah , if mah is low then working time also decrease

[@DhadamRobotics]

If possible used 7 to 12 v or 2000 mah

[@lionlion4761]

Nice application Update it with Nodmcu Esp8266 Wifi device

[@DhadamRobotics]

Yes, I try with this but In esp pin limitations or not properly interface

[@channelblue5298]

How much watt is the battery

[@DhadamRobotics]

7v Lipo 2A

[@jahanzaibaslamsiddique1805]

Great work...keep it up

[@DhadamRobotics]

Thanks brother

[@lionlion4761]

And make it little fast its relly so slow

[@DhadamRobotics]

Here, I Do faster Robo Then ,It may touch track side . Or sometime Not proper work , but you can try with this . 😊

[@poornaakalanka864]

Is that the code for what you just do how it takes smooth turns like that , did you use pid in video

[@DhadamRobotics]

Yes, motor driver or use low rpm motor

[@mohamedjamesha1289]

No pid

[@yudishmoonean5990]

Bro how can i use 3 ultrasonic sensor for obstacle detection and ir sensor to detect an end to make a robot that will follow a zig-zag path?

[@DhadamRobotics]

You mean line follower or obstacles avoid.

[@yudishmoonean5990]

@@DhadamRobotics obstacles avoidance

[@DhadamRobotics]

Yes , I Made ir sensor obstacles avoid ,but one disadvantage is that it not work in direct sunlight ,because ir sensor don't identify signal.

[@yudishmoonean5990]

@@DhadamRobotics what can i use sir?

[@DhadamRobotics]

Once go on my channel playlist or visit obstacles avoid robot playlist

[@Bhidhu_09]

I request please make 3d printed hand control with your hand via gesture

[@DhadamRobotics]

Check my video where I used gesture sensor to control stepper motor . So this only you add connection.

[@meterora9332]

Hey man, do you have the code for 2 wheels? I'm not able to get 4 motors, only 2. Making this for school project. Have never coded before in my life. if i use the code as is right now the robot spins around non stop

[@meterora9332]

i think now its working but it goes really fast that it just spins and reverses for 8m+/-

[@DhadamRobotics]

Yes two wheels maze solve also present ,check on my channel .

[@DhadamRobotics]

Yes two wheels maze solve also present ,check on my channel .

[@DhadamRobotics]

What RPM of your motor ??

[@meterora9332]

@@DhadamRobotics www.amazon.com/KEYESTUDIO-Motor-Arduino-Uniaxial-Wheels/dp/B07DRGTCTP im using these; 9v battery pack L298n ; how do you know which is positive / neg; do i follow the code (code says front has to be connected to const int trigPin1 = 11; const int echoPin1 = 10; U do it differently) Link to your video 2wd?

[@charlesreyes4410]

Sir i have a problem only the lefy wheel is working

[@DhadamRobotics]

First check your motor driver

[@charlesreyes4410]

I doubled check it sir and its attached nicely

[@tkromiyo830]

Thanks for sharing code or details

[@sanjanaattanayake4231]

Thank you very much for you guidance sir...🙏 I did this project... It's not perfect as yours but anyway it's working😊(My one can't avoid each and every single wall without hitting them at first but even if it it hits it then find it's path own😁😂) Best wishes for a bright future ahead...

[@DhadamRobotics]

Reduce motor rpm or speed

[@sanjanaattanayake4231]

@@DhadamRobotics Yeah it worked thank you very much 🙏😁

[@DhadamRobotics]

@@sanjanaattanayake4231 No mention dear, 😃

[@zulfaafnantuba7169]

can you please share the code

[@DhadamRobotics]

After donation

[@robertocorrea8498]

@DhadamRobotics holaaa, como puedo hacer el pago para obtener el codigo ?

[@DhadamRobotics]

Sorry used only English language

[@robertocorrea8498]

@@DhadamRobotics Hello. How can I make the payment to get the code? I finally found the video I was looking for so much. But I hope you can help me with the code. 🙏 Thank you.

[@DhadamRobotics]

@robertocorrea8498 used KZbin super thank of 10$ then after message me , we can provide access for code

[@k1_ldn139]

Is it possible that you can help me with the coding sometime this week or next week?

[@DhadamRobotics]

Yes dear, code present in description .also I Made same type 2wheel maze solve . Here present diagram or code also .check this video also for more details

[@SolutionFinder]

Great work bro...🤩🤗

[@DhadamRobotics]

Thanks bhai

[@savitamore3698]

We want code, we are ready to pay, can you help please, it's very important to do it for us

[@DhadamRobotics]

What's up on [phone]

[@MisaelRodriguez-wv4fh]

I need the code please🙏🏽

[@Just_A_Weeb_]

what is the voltage of the battery

[@DhadamRobotics]

7v

[@rovicsarmiento7939]

Do you have a code for 2 12v dc motors? We use only 2 motors

[@DhadamRobotics]

Then also same this method ,but connect only two motor

[@kavithadarshaka4872]

Do you know how to use pid control for this robot?

[@DhadamRobotics]

Yes bro.

[@kavithadarshaka4872]

Could you please make a video about that or put some references on description?☺️

[@DhadamRobotics]

I Make other 2wheel drive maze solve check this or all details available also you change parameter for change setting

[@DhadamRobotics]

Once watch my new maze solve robot video. If that any problem tell me

[@kavithadarshaka4872]

Thank you bro Your videos are very helpful❤️

[@TowfiqAhmed3ELab-Bogura]

So good

[@DhadamRobotics]

Thanks you ,brother

[@robertocorrea8498]

¡Gracias!

[@DhadamRobotics]

Thank you

[@saagarpanta9490]

can you provide the aurdino code

[@DhadamRobotics]

Check description bottom, present arduino code.

[@punitvachhani9676]

Do you know Flood Fill Algorithm?

[@mahammadkhanhonnur4513]

which battery are you used?

[@DhadamRobotics]

Home Made lipo battery

[@AbdulRasheed-zd2uz]

Hello Sir, can you provide code in email bcoz bottom one doesn't shows the code,

[@DhadamRobotics]

Sorry dear, first follow funds donation process , then after you access

[@AbdulRasheed-zd2uz]

@@DhadamRobotics then how can i pay the required amount,

[@DhadamRobotics]

using Gpay

[@AbdulRasheed-zd2uz]

@@DhadamRobotics it doesn't work in Pakistan,

[@DhadamRobotics]

Then no any solution

[@phongvuong12]

I can't do the same in the video, please help me

[@DhadamRobotics]

Follow Video Details or watch diagram

[@charlesreyes4410]

sir what is DIS in your code

[@DhadamRobotics]

Same As code

[@DhadamRobotics]

Same As my given code

[@rihambein7508]

can i get the google drive code and circuit plz

[@DhadamRobotics]

Yes but after donation

[@CumadcadNHSSHSDepartment]

how to pay from the Philippines?

[@DhadamRobotics]

Go with KZbin super thank,

[@zachcura5782]

Hey man, can I get access to your drive lin

[@DhadamRobotics]

Yess, after fund donation

[@rihambein7508]

Thanks!

[@VishalKumar-hm6pz]

I need the code, its urgent Please reply ASAP

[@DhadamRobotics]

Sorry dear code is not free for access follow description funds donation process then after you access it

[@VishalKumar-hm6pz]

@@DhadamRobotics I'll pay but i have to talk to you

[@DhadamRobotics]

What's up on 7575014342

[@user-tz8qv7ov4r]

Wow nice project

[@luzzz854]

How many dolars are for the code?

[@DhadamRobotics]

10$

[@luzzz854]

@@DhadamRobotics were i can deposit the money?

[@DhadamRobotics]

@luzzz854 go with KZbin super thank

[@luzzz854]

@@DhadamRobotics can you give me the account to deposit?

[@ghannysirat5339]

how many volt that battery?

[@DhadamRobotics]

7v , but you can used maximum 12V

[@zakriamuhammad283]

can i make my own code for this project? and how?

[@DhadamRobotics]

Yes, you are make your own code ,but you car all things otherwise not work .

[@rahulvaghela3529]

🔥🔥🔥🔥

[@DhadamRobotics]

Thanks you bhai

[@n550]

I CANT ACCESS CODE GOOGLE DRIVE SAYS ACCESS DENIED PLEASE HELP ME

[@DhadamRobotics]

Done donation first

[@n550]

@@DhadamRobotics where to donate ? how much to donate? tell me the process

[@DhadamRobotics]

@n550 450 what's up on [phone] for more details

[@irannahanjagi6584]

nice channel ,helpful

[@DhadamRobotics]

Thank you dear

[@abrarulkarimadib64]

the googl drive link of code is asking for access

[@DhadamRobotics]

Sorry dear code is not free for access follow description funds donation process then after you access.

[@smtorresm]

I can't find the code

[@DhadamRobotics]

Check description bottom ,I upload new code

[@rahmandamarjati7674]

Can you give me a code here?

[@DhadamRobotics]

Yes, after donation as per description

[@rahmandamarjati7674]

@@DhadamRobotics how?

[@DhadamRobotics]

What's up on [phone]

[@te_imamtreeutomo3163]

could you open the link acces for me please

[@DhadamRobotics]

Yes after donation

[@andresfelipevalenciaotero9348]

Hello, it asks me for permission to observe the code

[@DhadamRobotics]

Sorry , after donation as per description then after you access it

[@SteveJeffrin-x7k]

I have only one ultra Sonicsendor

[@DhadamRobotics]

This this not used , only one sensor type project alao available used that

[@AshwiniTirkey-x6u]

please give access to the code

[@DhadamRobotics]

Send donation receipt then after you access it

[@aniketkhade5250]

Are you indian

[@DhadamRobotics]

Yes ,dear

[@aniketkhade5250]

@@DhadamRobotics ok sir

[@DhadamRobotics]

Not sir , just friends Bhai

[@aniketkhade5250]

@@DhadamRobotics but I am 8 years old

[@DhadamRobotics]

No problem bro

[@Nishitosh06]

Awesome

[@DhadamRobotics]

Thank you dear

[@tricksforsolving2804]

Want this code??

[@DhadamRobotics]

Follow fund donation then after you access it

[@sanikagawande4347]

Where to pay 350

[@DhadamRobotics]

What's up on [phone]

[@juanarielgodoybaez5071]

That's just obstacle avoidance

[@DhadamRobotics]

Yes , same concept of obstruction avoid

[@pavans5268]

Maze runner code give me pls sir

[@DhadamRobotics]

Sorry dear code is not free for access follow description funds donation process then after you access it

[@fadialjazmati8795]

Where is the code??

[@DhadamRobotics]

In description , but for access done donation as per description

[@fadialjazmati8795]

Send me the payment link

[@abdelrhmanbedo7130]

please give the acess to see the code

[@DhadamRobotics]

Where you from

[@abdelrhmanbedo7130]

Egypt

[@abdelrhmanbedo7130]

I have to do this project but i have many problems in code

[@abdelrhmanbedo7130]

Can i get the acess?

[@DhadamRobotics]

Join youtube members of iot subscription. Once join then after message me

[@playz5594]

Brother I need code pls

[@DhadamRobotics]

Done donation and send receipt then after you access it

[@andreaandrea8660]

hello can i access the google drive of code please

[@DhadamRobotics]

Yes , but after donation

[@vekariyabhavtik127]

Wall following robot history

[@DhadamRobotics]

What you mean ? Dear

[@talhaabdurraheem8491]

Program not compiling

[@DhadamRobotics]

Sorry , something wrong in your method , use pc or laptop for arduino software

[@talhaabdurraheem8491]

@@DhadamRobotics Got it thanks, By the way mine was the best project in science exhibition

[@DhadamRobotics]

@@talhaabdurraheem8491 Thank you

[@VishalChauhan-iz5yt]

@@talhaabdurraheem8491 Congratulations !

[@aaiijjbbaa]

Code give

[@DhadamRobotics]

First done donation then after you access it

[@selenemena4313]

How can I pay?

[@DhadamRobotics]

What's up on+917575014342

[@selenemena4313]

Ok, I already sent you a message

[@DhadamRobotics]

No any message from your side, i check

[@selenemena4313]

@@DhadamRobotics I texted you on whatsapp but i didn't receive any message, I'm From Mexico . Help please, how? where can i donate?

[@DhadamRobotics]

Join channel membership " Iot Autonomous " , after joining reply here , or send new request with request id detail . I access it.

[@jyotibalwan6290]

Savni

[@praveenkumarvlogs17]

code send me bro

[@DhadamRobotics]

Done donation first

[@praveenkumarvlogs17]

how mach donetion @@DhadamRobotics

[@DhadamRobotics]

@praveenkumarvlogs17 check video description bottom part, all available

[@praveenkumarvlogs17]

ok@@DhadamRobotics

[@praveenkumarvlogs17]

Ok

[@rihambein7508]

Thanks!

[@DhadamRobotics]

Thank you