Measure and control the Conveyor Movement using Encoder as feedback device . S7 1200 PLC Project

[@soltanq1308]

You was the best in the youtube who expleain encoder with the short and bestway also with exempel. Thank you very much.

[@MenOfCulture8991]

what software you used for the conveyor simulation? thank you

[@raghavaram-uu8mo]

Very nice explained and for example thank you so much, make a different videos for encoder applications

[@mohammadkaheel973]

🎉

[@하고재비튭튭]

Hello, friend. Thank you for watching the good video Let me ask you a question Instead of the encoder, there are 20 magnets in the pulley and 170 mm diameter of the encoder pulley There's a 185mm driver pulley on the motor side Can't we use counter up-down to accurately calculate the travel distance like the encoder?? Please tell me how to do it!!

[@JesusHernandez-m1l]

Like You are the best, can you tell me the simulator name ?

[@الفارسيالفارسي-خ5ث]

Please could you tell me the name of the simulator

[@phandavin7123]

What software that you make Simulation?

[@ahmediibrahim.m3327]

F

[@rezababak2560]

@@ahmediibrahim.m3327 the name of simulation software is "F" ?!?!

[@zaffi_vibes]

TIA portal V17

[@umae4umahesh]

Hi,can you program,I have one Conyer based machine,if support please send reply,then I explain Thank you

[@electronicsdunapack5397]

Excellent tutorial!!

[@vorapobautomation9760]

What conveyor simulation do you using ?

[@ivanbrzica5100]

Which instruction to use to reset ID1000? many thanks

[@marcomachado39]

top d+++ valeu...

[@Manun_Papa]

Sir here I Request that please make video in Hindi language also for better understanding

[@Bilalashraf123]

good

[@A_R_94]

How do I get these files blender? Can you help me ❤

[@Sim_excently]

What is the simulation software in the video? please

[@vitfed933]

1:50 Why is the Network 1 needed at all? Why rewrite %ID1000 to %MD1000? Why convert Dint to Real?

[@monokouache1366]

Bc we need them as real to calculate mm per pulse

[@elohimstev.tech87]

Please help me with the name of the stimulator.

[@nournour7416]

How did you get differents speed between the setpoints ?

[@teknosistem]

thankyou sir.

[@mdosman1106]

Thanks

[@cuong9301]

i need name of Simulation app? pls

[@lockheadmaverick489]

Maybe this a little bit stupid question, but i'm not completely understand, how you convert discrete impulse I0.0 to analog value. One impulse you transfer to MD1000 but where you summarize impulses which gives analog value 1250 or 2500 etc?

[@sinanartemis6176]

first you should know what is encoder. encoder as a device when it rotates it produces pulses. basically. in that example you should connect that in digital signal instead of analog signal.but q.s? why? because pulses are digital values right? but also you should store that values in a big data as id1000 you can think like that you have a counter for counter up inout you should you a digital input but counter value must be md format. I hope that is clear for you

[@lockheadmaverick489]

@@sinanartemis6176 Thanks for the information. I understand why he connected the encoder to a discrete input. I do not understand where the summary of impulses occurs. MD1000 is this a counter?

[@sinanartemis6176]

@@lockheadmaverick489 when it start to count that pulse store in that value for instance in 1 revolution it takes 360pulse and when it contunue that value also also increases you can think like counter

[@darthenx2585]

​@lockheadmaverick489 yes MD1000 has been setup as a counter. In the beginning of the video when he is explaining the hardware configuration of the counter setup he mentioned the io address of the counter to start at memory address 1000. Kinda confusing but I found it.

[@mohammadmobin6971]

How you find out that encoder can move 15mm in a revolution, kindly clear it

[@ronnelelpa6878]

Why I can't open your Google drive

[@alifaraj5496]

Hello eng. what software that used for simulation

[@sinanartemis6176]

tia portal

[@rezababak2560]

Hi. Thanks for sharing. What is the full name of the simulation software?

[@meck_billions]

TIA Portal is good also

[@shadreckmugabe4841]

Thanks for the video, l got a question, anyone can help, to convert distance in mm covered per pulse, you divided 15mm/360ppr, where did 15 come from

[@UK211]

He found it from conveyor real speed ,it can be changed your project , I think

[@rsinurat2144]

What sofware simulation?

[@ahmediibrahim.m3327]

F

[@Learn-lp3nf]

how the motor receive signal ? in real, ask you 1v a 5V

[@stephenclarke8154]

Plc