Buy Best Conduit Bender from AMAZON amzn.to/3Ku17mw
Пікірлер: 37
@bmcfad122 жыл бұрын
I know you’re just showing the proper way that you should do it but honestly how many guys even put the vendor on the floor for a 30° offset or any offset for that matter other than a 90°? Most of my bending as an apprentice I’ve been taught to do in the air
@adams6798 Жыл бұрын
Great video but explain to people how multipliers are found using Trig?
@Bapuji422 жыл бұрын
This doesn't show how to use shrinkage to calculate for a given distance between the end of the conduit and the beginning of the first bend.
@diazaa4 жыл бұрын
Depending on bending angle you should put your mark on the tangent of the angle. In this scenario you can see that the mark is in front of the bend as it should be in the center of the bend. This is important if you need the bends to be in an exact location.
@AngelRomero9552 жыл бұрын
How do I put at mark at 0.57735026919?
@diazaa2 жыл бұрын
@@AngelRomero955 .57 degrees?
@AngelRomero9552 жыл бұрын
I found in another video that when making parallel runs with offsets. You need/want to use the Tangent of the offset angle. So it checks out. I’m a 1st year apprentice I still haven’t done any fancy bends.
@diazaa2 жыл бұрын
@@AngelRomero955ok but what was your question about marking at .57? I have alot of experience (10+yrs) measuring for, routing and bending hydraulic tubing.
@Bapuji422 жыл бұрын
@@AngelRomero955 Huh? The distance between marks is 1/sin(angle) times the offset rise.
@mohammedhassani39754 жыл бұрын
good job
@tragan14422 жыл бұрын
Soon to be cw here thanks for the vid
@chubbies22743 ай бұрын
Don’t do it go non union until u get inas a union apprentice
@divinepathways3133 жыл бұрын
hey viewed by me :D
@glennmann6343 жыл бұрын
Great video. Thanks for posting. Nice looking bender. What brand is it? (Thanks in advance for the answer.)
@passionateengineer043 жыл бұрын
Sorry i didn't remember the brand.
@ryanb18744 жыл бұрын
Does the diameter of the conduit have anythi g to do with the "shrink" or is it all treated like a thin line?
@passionateengineer044 жыл бұрын
Consider it as thin line.
@jakirsheikh26314 жыл бұрын
how need majarmant
@mariamontolla59784 жыл бұрын
Ok!! How tje eff do you find the multiplier
@ryanb18744 жыл бұрын
The multiplier has to do with the angle, it's 30 degrees, sine of 30 = .5. But we are dividing by SINE 30, so it's like multiply by 2. Get the uglies manual.
@diazaa4 жыл бұрын
45=1.414, 30=2, 15=3.86.... Those are the only ones I have memorized.
@lazarevic953 жыл бұрын
a way to find the multiplier for any bend angle is - 1/Sine(angle
@diazaa2 жыл бұрын
@@lazarevic95 Hey now, dont give away these magical tricks of the trade!!!
@alen22832 жыл бұрын
Its time to move on kopex like rest of the world!!
@juancarlosarayamanriquez28503 жыл бұрын
Si hubiera subtitulado español sinvirioa
@akurukyo62172 жыл бұрын
You probably forgot to show the 1st and 2nd step which is ; preparing the necessary materials,tools,and equipment. And wearing ppe
@patricktelfort4 жыл бұрын
What video is This from?
@passionateengineer044 жыл бұрын
For conduit bending
@patricktelfort4 жыл бұрын
The title of the actual video
@passionateengineer044 жыл бұрын
@@patricktelfort Multiplier method of offset bend
@jondyer47534 жыл бұрын
PASSIONATE ENGINEER Good video
@FuquarProductions Жыл бұрын
"pick a spot, bend it... then pick another spot, bent it... then you have nothing you're looking for. Thanks for not actually explaining what the multiplier is and how you find it.