Megan Racing Coilovers Install Part 2 (06 Lexus IS250)

[@jtrazz4038]

I’m looking to get the Megan coils for my TL. Looking forward to your review on these after u get some use out of them

[@Jason_Voorhees.]

2:49 the ghetto bird is out searching

[@brianyt56]

YES! Your video inspired me and got me through it. Thank you so much. It is sitting pretty right now, wish I can show you. Have a couple of questions and concerns, if you would be so kind.... Now that everything is installed and fit/ adjusted... I have 3 dash warning lights on: Brake, ABS, and Traction (car with 2 squiggly lines)... Did you run into that?

[@hectora2554]

I’ve never installed coilovers before but its seems straight forward hopefully everything goes right!

[@Leek_ee]

It should be very easy. You’ll get the hang of it forsure! 🤘

[@johnsally6304]

that shifting noise is crazy

[@malahi2106]

in my country the manual ones dont exist

[@jkhoeun59]

🔥🔥🔥🔥

[@brianyt56]

Hi 👋. Stance is wonderful 🔥. In addition to the Megan CO’s what did you do for the camber?

[@Leek_ee]

Since it’s natural camber. I let it sit how it is. Taking it to the alignment shop can adjust the camber very slightly. Overall, I suggest camber arms to get full range of camber adjustment

[@brianyt56]

Thank you

[@brianyt56]

Fyi: Megan’s customer service sucks! I’ve been trying to get a hold of them to see if they can help spec out the coilovers and camber kit… I can do a better job just by using their website-- but I just wanted them to double check my work. 🤦‍♂️ Because of this, I think I'm going with Tein's. I had Tein's on my ES for 12 years, and I was very happy with it. Because of your vid and some other folks, I was considering Megan. But because their CS sucks so bad, I dont wanna deal w/ them. I'm prol going to spend $1500-2K on the CO's and Camber kits.... and I'm afraid they won't be very responsive if i ran into any issues. Anyway, thank you very much for your videos.

[@brianyt56]

Oh yeah, another question.... Is Swaybar needed after lowering?

[@Leek_ee]

@@brianyt56 No need for that. Unless you're going the performance route.

[@trentnuckolls2697]

did you torque all the bolts to spec or did you hand tighten? If you have the torques, would you mind sharing them?

[@Leek_ee]

25lb of torque is recommended

[@jasontran7473]

@@Leek_ee 25lb for all the bolts?

[@xXBigWedoXx]

No spring compressor needed for the back? Got some Tien advance Z to install this week

[@Leek_ee]

Nawww, let the jack down very slowly 😂😂

[@orlandooropeza2305]

Excellent 💪🏻🔥🔥🔥🔥🔥

[@eduardoe9295]

did you have to pre-load the coils at all or did you just fit them on the car the way they came ?

[@Leek_ee]

It usually comes preload from factory. No need to adjust it. Only adjust dampening and ride height

[@zzztroper]

​@@Leek_eenever listen to preload load set from factory. Bs!!!!! I using rev9 coilovers. I added 1/4inch to the preload, rides like a dream

[@Slackful]

hows the rid qual

[@mariuszrogacki1343]

Hello, by how many cm have you lowered?

[@Leek_ee]

I dropped it about 3 1/2 inches

[@CarbonLexus]

Are you awd or rwd?

[@CarbonLexus]

And did you is RCA spacers in the front?

[@generic5353]

Turn the comments back on for your plastidip video lol

[@ARon82]

I have a 2008 with 85k want to lower it how much did it cost?

[@Leek_ee]

Coilovers we’re around $500-$600 I think